diff options
Diffstat (limited to 'arch/arm/mach-mxs/power-init.c')
| -rw-r--r-- | arch/arm/mach-mxs/power-init.c | 1272 |
1 files changed, 1272 insertions, 0 deletions
diff --git a/arch/arm/mach-mxs/power-init.c b/arch/arm/mach-mxs/power-init.c new file mode 100644 index 0000000000..977c6e4e27 --- /dev/null +++ b/arch/arm/mach-mxs/power-init.c @@ -0,0 +1,1272 @@ +/* + * Freescale i.MX28 Boot PMIC init + * + * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com> + * on behalf of DENX Software Engineering GmbH + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <config.h> +#include <io.h> +#include <mach/imx-regs.h> + +#include <mach/generic.h> +#include <mach/init.h> +#ifdef CONFIG_ARCH_IMX23 +#include <mach/regs-clkctrl-mx23.h> +#endif +#ifdef CONFIG_ARCH_IMX28 +#include <mach/regs-clkctrl-mx28.h> +#endif +#include <mach/regs-power-mx28.h> +#include <mach/regs-rtc.h> +#include <mach/regs-lradc.h> + +/* + * This delay function is intended to be used only in early stage of boot, where + * clock are not set up yet. The timer used here is reset on every boot and + * takes a few seconds to roll. The boot doesn't take that long, so to keep the + * code simple, it doesn't take rolling into consideration. + */ +void mxs_early_delay(int delay) +{ + void __iomem *digctl_regs = IOMEM(IMX_DIGCTL_BASE); + uint32_t st = readl(digctl_regs + 0xc0); + + st += delay; + + while (st > readl(digctl_regs + 0xc0)); +} + +static inline void charger_4p2_disable(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + if (cpu_is_mx28()) + writel(MX28_POWER_5VCTRL_PWD_CHARGE_4P2_MASK, + &power_regs->hw_power_5vctrl_set); + else + writel(MX23_POWER_5VCTRL_PWD_CHARGE_4P2_MASK, + &power_regs->hw_power_5vctrl_set); +} + +static inline void charger_4p2_enable(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + if (cpu_is_mx28()) + writel(MX28_POWER_5VCTRL_PWD_CHARGE_4P2_MASK, + &power_regs->hw_power_5vctrl_clr); + else + writel(MX23_POWER_5VCTRL_PWD_CHARGE_4P2_MASK, + &power_regs->hw_power_5vctrl_clr); +} + +/** + * mxs_power_clock2xtal() - Switch CPU core clock source to 24MHz XTAL + * + * This function switches the CPU core clock from PLL to 24MHz XTAL + * oscilator. This is necessary if the PLL is being reconfigured to + * prevent crash of the CPU core. + */ +static void mxs_power_clock2xtal(void) +{ + struct mxs_clkctrl_regs *clkctrl_regs = + (struct mxs_clkctrl_regs *)IMX_CCM_BASE; + + /* Set XTAL as CPU reference clock */ + writel(CLKCTRL_CLKSEQ_BYPASS_CPU, + &clkctrl_regs->hw_clkctrl_clkseq_set); +} + +/** + * mxs_power_clock2pll() - Switch CPU core clock source to PLL + * + * This function switches the CPU core clock from 24MHz XTAL oscilator + * to PLL. This can only be called once the PLL has re-locked and once + * the PLL is stable after reconfiguration. + */ +static void mxs_power_clock2pll(void) +{ + struct mxs_clkctrl_regs *clkctrl_regs = + (struct mxs_clkctrl_regs *)IMX_CCM_BASE; + + setbits_le32(&clkctrl_regs->hw_clkctrl_pll0ctrl0, + CLKCTRL_PLL0CTRL0_POWER); + mxs_early_delay(100); + setbits_le32(&clkctrl_regs->hw_clkctrl_clkseq, + CLKCTRL_CLKSEQ_BYPASS_CPU); +} + +/** + * mxs_power_set_auto_restart() - Set the auto-restart bit + * + * This function ungates the RTC block and sets the AUTO_RESTART + * bit to work around a design bug on MX28EVK Rev. A . + */ + +static void mxs_power_set_auto_restart(void) +{ + struct mxs_rtc_regs *rtc_regs = + (struct mxs_rtc_regs *)IMX_WDT_BASE; + + writel(RTC_CTRL_SFTRST, &rtc_regs->hw_rtc_ctrl_clr); + while (readl(&rtc_regs->hw_rtc_ctrl) & RTC_CTRL_SFTRST) + ; + + writel(RTC_CTRL_CLKGATE, &rtc_regs->hw_rtc_ctrl_clr); + while (readl(&rtc_regs->hw_rtc_ctrl) & RTC_CTRL_CLKGATE) + ; + + /* Do nothing if flag already set */ + if (readl(&rtc_regs->hw_rtc_persistent0) & RTC_PERSISTENT0_AUTO_RESTART) + return; + + while (readl(&rtc_regs->hw_rtc_stat) & RTC_STAT_NEW_REGS_MASK) + ; + + setbits_le32(&rtc_regs->hw_rtc_persistent0, + RTC_PERSISTENT0_AUTO_RESTART); + writel(RTC_CTRL_FORCE_UPDATE, &rtc_regs->hw_rtc_ctrl_set); + writel(RTC_CTRL_FORCE_UPDATE, &rtc_regs->hw_rtc_ctrl_clr); + while (readl(&rtc_regs->hw_rtc_stat) & RTC_STAT_NEW_REGS_MASK) + ; + while (readl(&rtc_regs->hw_rtc_stat) & RTC_STAT_STALE_REGS_MASK) + ; +} + +/** + * mxs_power_set_linreg() - Set linear regulators 25mV below DC-DC converter + * + * This function configures the VDDIO, VDDA and VDDD linear regulators output + * to be 25mV below the VDDIO, VDDA and VDDD output from the DC-DC switching + * converter. This is the recommended setting for the case where we use both + * linear regulators and DC-DC converter to power the VDDIO rail. + */ +static void mxs_power_set_linreg(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + /* Set linear regulator 25mV below switching converter */ + clrsetbits_le32(&power_regs->hw_power_vdddctrl, + POWER_VDDDCTRL_LINREG_OFFSET_MASK, + POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW); + + clrsetbits_le32(&power_regs->hw_power_vddactrl, + POWER_VDDACTRL_LINREG_OFFSET_MASK, + POWER_VDDACTRL_LINREG_OFFSET_1STEPS_BELOW); + + clrsetbits_le32(&power_regs->hw_power_vddioctrl, + POWER_VDDIOCTRL_LINREG_OFFSET_MASK, + POWER_VDDIOCTRL_LINREG_OFFSET_1STEPS_BELOW); +} + +/** + * mxs_get_batt_volt() - Measure battery input voltage + * + * This function retrieves the battery input voltage and returns it. + */ +static int mxs_get_batt_volt(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + uint32_t volt = readl(&power_regs->hw_power_battmonitor); + + volt &= POWER_BATTMONITOR_BATT_VAL_MASK; + volt >>= POWER_BATTMONITOR_BATT_VAL_OFFSET; + volt *= 8; + + return volt; +} + +/** + * mxs_is_batt_ready() - Test if the battery provides enough voltage to boot + * + * This function checks if the battery input voltage is higher than 3.6V and + * therefore allows the system to successfully boot using this power source. + */ +static int mxs_is_batt_ready(void) +{ + return (mxs_get_batt_volt() >= 3600); +} + +/** + * mxs_is_batt_good() - Test if battery is operational at all + * + * This function starts recharging the battery and tests if the input current + * provided by the 5V input recharging the battery is also sufficient to power + * the DC-DC converter. + */ +static int mxs_is_batt_good(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + uint32_t volt = mxs_get_batt_volt(); + + if ((volt >= 2400) && (volt <= 4300)) + return 1; + + clrsetbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK, + 0x3 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET); + charger_4p2_enable(); + + clrsetbits_le32(&power_regs->hw_power_charge, + POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK, + POWER_CHARGE_STOP_ILIMIT_10MA | 0x3); + + writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_clr); + charger_4p2_enable(); + + mxs_early_delay(500000); + + volt = mxs_get_batt_volt(); + + if (volt >= 3500) + return 0; + + if (volt >= 2400) + return 1; + + writel(POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK, + &power_regs->hw_power_charge_clr); + writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_set); + + return 0; +} + +/** + * mxs_power_setup_5v_detect() - Start the 5V input detection comparator + * + * This function enables the 5V detection comparator and sets the 5V valid + * threshold to 4.4V . We use 4.4V threshold here to make sure that even + * under high load, the voltage drop on the 5V input won't be so critical + * to cause undervolt on the 4P2 linear regulator supplying the DC-DC + * converter and thus making the system crash. + */ +static void mxs_power_setup_5v_detect(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + /* Start 5V detection */ + clrsetbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_VBUSVALID_TRSH_MASK, + POWER_5VCTRL_VBUSVALID_TRSH_4V4 | + POWER_5VCTRL_PWRUP_VBUS_CMPS); +} + +/** + * mxs_src_power_init() - Preconfigure the power block + * + * This function configures reasonable values for the DC-DC control loop + * and battery monitor. + */ +static void mxs_src_power_init(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + /* Improve efficieny and reduce transient ripple */ + writel(POWER_LOOPCTRL_TOGGLE_DIF | POWER_LOOPCTRL_EN_CM_HYST | + POWER_LOOPCTRL_EN_DF_HYST, &power_regs->hw_power_loopctrl_set); + + clrsetbits_le32(&power_regs->hw_power_dclimits, + POWER_DCLIMITS_POSLIMIT_BUCK_MASK, + 0x30 << POWER_DCLIMITS_POSLIMIT_BUCK_OFFSET); + + setbits_le32(&power_regs->hw_power_battmonitor, + POWER_BATTMONITOR_EN_BATADJ); + + /* Increase the RCSCALE level for quick DCDC response to dynamic load */ + clrsetbits_le32(&power_regs->hw_power_loopctrl, + POWER_LOOPCTRL_EN_RCSCALE_MASK, + POWER_LOOPCTRL_RCSCALE_THRESH | + POWER_LOOPCTRL_EN_RCSCALE_8X); + + clrsetbits_le32(&power_regs->hw_power_minpwr, + POWER_MINPWR_HALFFETS, POWER_MINPWR_DOUBLE_FETS); + + /* 5V to battery handoff ... FIXME */ + setbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER); + mxs_early_delay(30); + clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER); +} + +/** + * mxs_power_init_4p2_params() - Configure the parameters of the 4P2 regulator + * + * This function configures the necessary parameters for the 4P2 linear + * regulator to supply the DC-DC converter from 5V input. + */ +static void mxs_power_init_4p2_params(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + /* Setup 4P2 parameters */ + clrsetbits_le32(&power_regs->hw_power_dcdc4p2, + POWER_DCDC4P2_CMPTRIP_MASK | POWER_DCDC4P2_TRG_MASK, + POWER_DCDC4P2_TRG_4V2 | (31 << POWER_DCDC4P2_CMPTRIP_OFFSET)); + + clrsetbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_HEADROOM_ADJ_MASK, + 0x4 << POWER_5VCTRL_HEADROOM_ADJ_OFFSET); + + clrsetbits_le32(&power_regs->hw_power_dcdc4p2, + POWER_DCDC4P2_DROPOUT_CTRL_MASK, + POWER_DCDC4P2_DROPOUT_CTRL_100MV | + POWER_DCDC4P2_DROPOUT_CTRL_SRC_SEL); + + clrsetbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK, + 0x3f << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET); +} + +/** + * mxs_enable_4p2_dcdc_input() - Enable or disable the DCDC input from 4P2 + * @xfer: Select if the input shall be enabled or disabled + * + * This function enables or disables the 4P2 input into the DC-DC converter. + */ +static void mxs_enable_4p2_dcdc_input(int xfer) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + uint32_t tmp, vbus_thresh, vbus_5vdetect, pwd_bo; + uint32_t prev_5v_brnout, prev_5v_droop; + + prev_5v_brnout = readl(&power_regs->hw_power_5vctrl) & + POWER_5VCTRL_PWDN_5VBRNOUT; + prev_5v_droop = readl(&power_regs->hw_power_ctrl) & + POWER_CTRL_ENIRQ_VDD5V_DROOP; + + clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_PWDN_5VBRNOUT); + writel(POWER_RESET_UNLOCK_KEY | POWER_RESET_PWD_OFF, + &power_regs->hw_power_reset); + + clrbits_le32(&power_regs->hw_power_ctrl, POWER_CTRL_ENIRQ_VDD5V_DROOP); + + if (xfer && (readl(&power_regs->hw_power_5vctrl) & + POWER_5VCTRL_ENABLE_DCDC)) { + return; + } + + /* + * Recording orignal values that will be modified temporarlily + * to handle a chip bug. See chip errata for CQ ENGR00115837 + */ + tmp = readl(&power_regs->hw_power_5vctrl); + vbus_thresh = tmp & POWER_5VCTRL_VBUSVALID_TRSH_MASK; + vbus_5vdetect = tmp & POWER_5VCTRL_VBUSVALID_5VDETECT; + + pwd_bo = readl(&power_regs->hw_power_minpwr) & POWER_MINPWR_PWD_BO; + + /* + * Disable mechanisms that get erroneously tripped by when setting + * the DCDC4P2 EN_DCDC + */ + clrbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_VBUSVALID_5VDETECT | + POWER_5VCTRL_VBUSVALID_TRSH_MASK); + + writel(POWER_MINPWR_PWD_BO, &power_regs->hw_power_minpwr_set); + + if (xfer) { + setbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_DCDC_XFER); + mxs_early_delay(20); + clrbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_DCDC_XFER); + + setbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_ENABLE_DCDC); + } else { + setbits_le32(&power_regs->hw_power_dcdc4p2, + POWER_DCDC4P2_ENABLE_DCDC); + } + + mxs_early_delay(25); + + clrsetbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_VBUSVALID_TRSH_MASK, vbus_thresh); + + if (vbus_5vdetect) + writel(vbus_5vdetect, &power_regs->hw_power_5vctrl_set); + + if (!pwd_bo) + clrbits_le32(&power_regs->hw_power_minpwr, POWER_MINPWR_PWD_BO); + + while (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VBUS_VALID_IRQ) + writel(POWER_CTRL_VBUS_VALID_IRQ, + &power_regs->hw_power_ctrl_clr); + + if (prev_5v_brnout) { + writel(POWER_5VCTRL_PWDN_5VBRNOUT, + &power_regs->hw_power_5vctrl_set); + writel(POWER_RESET_UNLOCK_KEY, + &power_regs->hw_power_reset); + } else { + writel(POWER_5VCTRL_PWDN_5VBRNOUT, + &power_regs->hw_power_5vctrl_clr); + writel(POWER_RESET_UNLOCK_KEY | POWER_RESET_PWD_OFF, + &power_regs->hw_power_reset); + } + + while (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VDD5V_DROOP_IRQ) + writel(POWER_CTRL_VDD5V_DROOP_IRQ, + &power_regs->hw_power_ctrl_clr); + + if (prev_5v_droop) + clrbits_le32(&power_regs->hw_power_ctrl, + POWER_CTRL_ENIRQ_VDD5V_DROOP); + else + setbits_le32(&power_regs->hw_power_ctrl, + POWER_CTRL_ENIRQ_VDD5V_DROOP); +} + +/** + * mxs_power_init_4p2_regulator() - Start the 4P2 regulator + * + * This function enables the 4P2 regulator and switches the DC-DC converter + * to use the 4P2 input. + */ +static void mxs_power_init_4p2_regulator(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + uint32_t tmp, tmp2; + + setbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_ENABLE_4P2); + + writel(POWER_CHARGE_ENABLE_LOAD, &power_regs->hw_power_charge_set); + + writel(POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK, + &power_regs->hw_power_5vctrl_clr); + clrbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_TRG_MASK); + + /* Power up the 4p2 rail and logic/control */ + charger_4p2_enable(); + + /* + * Start charging up the 4p2 capacitor. We ramp of this charge + * gradually to avoid large inrush current from the 5V cable which can + * cause transients/problems + */ + mxs_enable_4p2_dcdc_input(0); + + if (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VBUS_VALID_IRQ) { + /* + * If we arrived here, we were unable to recover from mx23 chip + * errata 5837. 4P2 is disabled and sufficient battery power is + * not present. Exiting to not enable DCDC power during 5V + * connected state. + */ + clrbits_le32(&power_regs->hw_power_dcdc4p2, + POWER_DCDC4P2_ENABLE_DCDC); + charger_4p2_disable(); + hang(); + } + + /* + * Here we set the 4p2 brownout level to something very close to 4.2V. + * We then check the brownout status. If the brownout status is false, + * the voltage is already close to the target voltage of 4.2V so we + * can go ahead and set the 4P2 current limit to our max target limit. + * If the brownout status is true, we need to ramp us the current limit + * so that we don't cause large inrush current issues. We step up the + * current limit until the brownout status is false or until we've + * reached our maximum defined 4p2 current limit. + */ + clrsetbits_le32(&power_regs->hw_power_dcdc4p2, + POWER_DCDC4P2_BO_MASK, + 22 << POWER_DCDC4P2_BO_OFFSET); /* 4.15V */ + + if (!(readl(&power_regs->hw_power_sts) & POWER_STS_DCDC_4P2_BO)) { + setbits_le32(&power_regs->hw_power_5vctrl, + 0x3f << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET); + } else { + tmp = (readl(&power_regs->hw_power_5vctrl) & + POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK) >> + POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET; + while (tmp < 0x3f) { + if (!(readl(&power_regs->hw_power_sts) & + POWER_STS_DCDC_4P2_BO)) { + tmp = readl(&power_regs->hw_power_5vctrl); + tmp |= POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK; + mxs_early_delay(100); + writel(tmp, &power_regs->hw_power_5vctrl); + break; + } else { + tmp++; + tmp2 = readl(&power_regs->hw_power_5vctrl); + tmp2 &= ~POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK; + tmp2 |= tmp << + POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET; + writel(tmp2, &power_regs->hw_power_5vctrl); + mxs_early_delay(100); + } + } + } + + clrbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_BO_MASK); + writel(POWER_CTRL_DCDC4P2_BO_IRQ, &power_regs->hw_power_ctrl_clr); +} + +/** + * mxs_power_init_dcdc_4p2_source() - Switch DC-DC converter to 4P2 source + * + * This function configures the DC-DC converter to be supplied from the 4P2 + * linear regulator. + */ +static void mxs_power_init_dcdc_4p2_source(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + if (!(readl(&power_regs->hw_power_dcdc4p2) & + POWER_DCDC4P2_ENABLE_DCDC)) { + hang(); + } + + mxs_enable_4p2_dcdc_input(1); + + if (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VBUS_VALID_IRQ) { + clrbits_le32(&power_regs->hw_power_dcdc4p2, + POWER_DCDC4P2_ENABLE_DCDC); + writel(POWER_5VCTRL_ENABLE_DCDC, + &power_regs->hw_power_5vctrl_clr); + charger_4p2_disable(); + } +} + +/** + * mxs_power_enable_4p2() - Power up the 4P2 regulator + * + * This function drives the process of powering up the 4P2 linear regulator + * and switching the DC-DC converter input over to the 4P2 linear regulator. + */ +static void mxs_power_enable_4p2(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + uint32_t vdddctrl, vddactrl, vddioctrl; + uint32_t tmp; + + vdddctrl = readl(&power_regs->hw_power_vdddctrl); + vddactrl = readl(&power_regs->hw_power_vddactrl); + vddioctrl = readl(&power_regs->hw_power_vddioctrl); + + setbits_le32(&power_regs->hw_power_vdddctrl, + POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG | + POWER_VDDDCTRL_PWDN_BRNOUT); + + setbits_le32(&power_regs->hw_power_vddactrl, + POWER_VDDACTRL_DISABLE_FET | POWER_VDDACTRL_ENABLE_LINREG | + POWER_VDDACTRL_PWDN_BRNOUT); + + setbits_le32(&power_regs->hw_power_vddioctrl, + POWER_VDDIOCTRL_DISABLE_FET | POWER_VDDIOCTRL_PWDN_BRNOUT); + + mxs_power_init_4p2_params(); + mxs_power_init_4p2_regulator(); + + /* Shutdown battery (none present) */ + if (!mxs_is_batt_ready()) { + clrbits_le32(&power_regs->hw_power_dcdc4p2, + POWER_DCDC4P2_BO_MASK); + writel(POWER_CTRL_DCDC4P2_BO_IRQ, + &power_regs->hw_power_ctrl_clr); + writel(POWER_CTRL_ENIRQ_DCDC4P2_BO, + &power_regs->hw_power_ctrl_clr); + } + + mxs_power_init_dcdc_4p2_source(); + + writel(vdddctrl, &power_regs->hw_power_vdddctrl); + mxs_early_delay(20); + writel(vddactrl, &power_regs->hw_power_vddactrl); + mxs_early_delay(20); + writel(vddioctrl, &power_regs->hw_power_vddioctrl); + + /* + * Check if FET is enabled on either powerout and if so, + * disable load. + */ + tmp = 0; + tmp |= !(readl(&power_regs->hw_power_vdddctrl) & + POWER_VDDDCTRL_DISABLE_FET); + tmp |= !(readl(&power_regs->hw_power_vddactrl) & + POWER_VDDACTRL_DISABLE_FET); + tmp |= !(readl(&power_regs->hw_power_vddioctrl) & + POWER_VDDIOCTRL_DISABLE_FET); + if (tmp) + writel(POWER_CHARGE_ENABLE_LOAD, + &power_regs->hw_power_charge_clr); +} + +/** + * mxs_boot_valid_5v() - Boot from 5V supply + * + * This function configures the power block to boot from valid 5V input. + * This is called only if the 5V is reliable and can properly supply the + * CPU. This function proceeds to configure the 4P2 converter to be supplied + * from the 5V input. + */ +static void mxs_boot_valid_5v(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + /* + * Use VBUSVALID level instead of VDD5V_GT_VDDIO level to trigger a 5V + * disconnect event. FIXME + */ + writel(POWER_5VCTRL_VBUSVALID_5VDETECT, + &power_regs->hw_power_5vctrl_set); + + /* Configure polarity to check for 5V disconnection. */ + writel(POWER_CTRL_POLARITY_VBUSVALID | + POWER_CTRL_POLARITY_VDD5V_GT_VDDIO, + &power_regs->hw_power_ctrl_clr); + + writel(POWER_CTRL_VBUS_VALID_IRQ | POWER_CTRL_VDD5V_GT_VDDIO_IRQ, + &power_regs->hw_power_ctrl_clr); + + mxs_power_enable_4p2(); +} + +/** + * mxs_powerdown() - Shut down the system + * + * This function powers down the CPU completely. + */ +static void mxs_powerdown(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + writel(POWER_RESET_UNLOCK_KEY, &power_regs->hw_power_reset); + writel(POWER_RESET_UNLOCK_KEY | POWER_RESET_PWD_OFF, + &power_regs->hw_power_reset); +} + +/** + * mxs_enable_battery_input() - Configure the power block to boot from battery input + * + * This function configures the power block to boot from the battery voltage + * supply. + */ +static void mxs_enable_battery_input(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_PWDN_5VBRNOUT); + clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_ENABLE_DCDC); + + clrbits_le32(&power_regs->hw_power_dcdc4p2, + POWER_DCDC4P2_ENABLE_DCDC | POWER_DCDC4P2_ENABLE_4P2); + writel(POWER_CHARGE_ENABLE_LOAD, &power_regs->hw_power_charge_clr); + + /* 5V to battery handoff. */ + setbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER); + mxs_early_delay(30); + clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER); + + writel(POWER_CTRL_ENIRQ_DCDC4P2_BO, &power_regs->hw_power_ctrl_clr); + + clrsetbits_le32(&power_regs->hw_power_minpwr, + POWER_MINPWR_HALFFETS, POWER_MINPWR_DOUBLE_FETS); + + mxs_power_set_linreg(); + + clrbits_le32(&power_regs->hw_power_vdddctrl, + POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG); + + clrbits_le32(&power_regs->hw_power_vddactrl, + POWER_VDDACTRL_DISABLE_FET | POWER_VDDACTRL_ENABLE_LINREG); + + clrbits_le32(&power_regs->hw_power_vddioctrl, + POWER_VDDIOCTRL_DISABLE_FET); + + charger_4p2_disable(); + + setbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_ENABLE_DCDC); + + clrsetbits_le32(&power_regs->hw_power_5vctrl, + POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK, + 0x8 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET); + + mxs_power_enable_4p2(); +} + +/** + * mxs_handle_5v_conflict() - Test if the 5V input is reliable + * + * This function tests if the 5V input can reliably supply the system. If it + * can, then proceed to configuring the system to boot from 5V source, otherwise + * try booting from battery supply. If we can not boot from battery supply + * either, shut down the system. + */ +static void mxs_handle_5v_conflict(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + uint32_t tmp; + + setbits_le32(&power_regs->hw_power_vddioctrl, + POWER_VDDIOCTRL_BO_OFFSET_MASK); + + for (;;) { + tmp = readl(&power_regs->hw_power_sts); + + if (tmp & POWER_STS_VDDIO_BO) { + /* + * VDDIO has a brownout, then the VDD5V_GT_VDDIO becomes + * unreliable + */ + mxs_powerdown(); + break; + } + + if (tmp & POWER_STS_VDD5V_GT_VDDIO) { + mxs_boot_valid_5v(); + break; + } else { + mxs_powerdown(); + break; + } + + if (tmp & POWER_STS_PSWITCH_MASK) { + mxs_enable_battery_input(); + break; + } + } +} + +/** + * mxs_5v_boot() - Configure the power block to boot from 5V input + * + * This function handles configuration of the power block when supplied by + * a 5V input. + */ +static void mxs_5v_boot(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + /* + * NOTE: In original IMX-Bootlets, this also checks for VBUSVALID, + * but their implementation always returns 1 so we omit it here. + */ + if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) { + mxs_boot_valid_5v(); + return; + } + + mxs_early_delay(1000); + if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) { + mxs_boot_valid_5v(); + return; + } + + mxs_handle_5v_conflict(); +} + +/** + * mxs_init_batt_bo() - Configure battery brownout threshold + * + * This function configures the battery input brownout threshold. The value + * at which the battery brownout happens is configured to 3.0V in the code. + */ +static void mxs_init_batt_bo(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + /* Brownout at 3V */ + clrsetbits_le32(&power_regs->hw_power_battmonitor, + POWER_BATTMONITOR_BRWNOUT_LVL_MASK, + 15 << POWER_BATTMONITOR_BRWNOUT_LVL_OFFSET); + + writel(POWER_CTRL_BATT_BO_IRQ, &power_regs->hw_power_ctrl_clr); + writel(POWER_CTRL_ENIRQ_BATT_BO, &power_regs->hw_power_ctrl_clr); +} + +/** + * mxs_switch_vddd_to_dcdc_source() - Switch VDDD rail to DC-DC converter + * + * This function turns off the VDDD linear regulator and therefore makes + * the VDDD rail be supplied only by the DC-DC converter. + */ +static void mxs_switch_vddd_to_dcdc_source(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + clrsetbits_le32(&power_regs->hw_power_vdddctrl, + POWER_VDDDCTRL_LINREG_OFFSET_MASK, + POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW); + + clrbits_le32(&power_regs->hw_power_vdddctrl, + POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG | + POWER_VDDDCTRL_DISABLE_STEPPING); +} + +/** + * mxs_power_configure_power_source() - Configure power block source + * + * This function is the core of the power configuration logic. The function + * selects the power block input source and configures the whole power block + * accordingly. After the configuration is complete and the system is stable + * again, the function switches the CPU clock source back to PLL. Finally, + * the function switches the voltage rails to DC-DC converter. + */ +static void mxs_power_configure_power_source(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + struct mxs_lradc_regs *lradc_regs = + (struct mxs_lradc_regs *)IMX_LRADC_BASE; + + if (!(readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO)) { + /* 5V not detected, booting from battery. */ + mxs_enable_battery_input(); + return; + } + + if (mxs_is_batt_ready()) { + /* 5V source detected, good battery detected. */ + mxs_enable_battery_input(); + return; + } + + if (!mxs_is_batt_good()) { + /* 5V source detected, bad battery detected. */ + writel(LRADC_CONVERSION_AUTOMATIC, + &lradc_regs->hw_lradc_conversion_clr); + clrbits_le32(&power_regs->hw_power_battmonitor, + POWER_BATTMONITOR_BATT_VAL_MASK); + } + mxs_5v_boot(); +} + +/** + * mxs_enable_output_rail_protection() - Enable power rail protection + * + * This function enables overload protection on the power rails. This is + * triggered if the power rails' voltage drops rapidly due to overload and + * in such case, the supply to the powerrail is cut-off, protecting the + * CPU from damage. Note that under such condition, the system will likely + * crash or misbehave. + */ +static void mxs_enable_output_rail_protection(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + writel(POWER_CTRL_VDDD_BO_IRQ | POWER_CTRL_VDDA_BO_IRQ | + POWER_CTRL_VDDIO_BO_IRQ, &power_regs->hw_power_ctrl_clr); + + setbits_le32(&power_regs->hw_power_vdddctrl, + POWER_VDDDCTRL_PWDN_BRNOUT); + + setbits_le32(&power_regs->hw_power_vddactrl, + POWER_VDDACTRL_PWDN_BRNOUT); + + setbits_le32(&power_regs->hw_power_vddioctrl, + POWER_VDDIOCTRL_PWDN_BRNOUT); +} + +/** + * mxs_get_vddio_power_source_off() - Get VDDIO rail power source + * + * This function tests if the VDDIO rail is supplied by linear regulator + * or by the DC-DC converter. Returns 1 if powered by linear regulator, + * returns 0 if powered by the DC-DC converter. + */ +static int mxs_get_vddio_power_source_off(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + uint32_t tmp; + + if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) { + tmp = readl(&power_regs->hw_power_vddioctrl); + if (tmp & POWER_VDDIOCTRL_DISABLE_FET) { + if ((tmp & POWER_VDDIOCTRL_LINREG_OFFSET_MASK) == + POWER_VDDIOCTRL_LINREG_OFFSET_0STEPS) { + return 1; + } + } + + if (!(readl(&power_regs->hw_power_5vctrl) & + POWER_5VCTRL_ENABLE_DCDC)) { + if ((tmp & POWER_VDDIOCTRL_LINREG_OFFSET_MASK) == + POWER_VDDIOCTRL_LINREG_OFFSET_0STEPS) { + return 1; + } + } + } + + return 0; + +} + +/** + * mxs_get_vddd_power_source_off() - Get VDDD rail power source + * + * This function tests if the VDDD rail is supplied by linear regulator + * or by the DC-DC converter. Returns 1 if powered by linear regulator, + * returns 0 if powered by the DC-DC converter. + */ +static int mxs_get_vddd_power_source_off(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + uint32_t tmp; + + tmp = readl(&power_regs->hw_power_vdddctrl); + if (tmp & POWER_VDDDCTRL_DISABLE_FET) { + if ((tmp & POWER_VDDDCTRL_LINREG_OFFSET_MASK) == + POWER_VDDDCTRL_LINREG_OFFSET_0STEPS) { + return 1; + } + } + + if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) { + if (!(readl(&power_regs->hw_power_5vctrl) & + POWER_5VCTRL_ENABLE_DCDC)) { + return 1; + } + } + + if (!(tmp & POWER_VDDDCTRL_ENABLE_LINREG)) { + if ((tmp & POWER_VDDDCTRL_LINREG_OFFSET_MASK) == + POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW) { + return 1; + } + } + + return 0; +} + +struct mxs_vddx_cfg { + uint32_t *reg; + uint8_t step_mV; + uint16_t lowest_mV; + int (*powered_by_linreg)(void); + uint32_t trg_mask; + uint32_t bo_irq; + uint32_t bo_enirq; + uint32_t bo_offset_mask; + uint32_t bo_offset_offset; +}; + +static const struct mxs_vddx_cfg mx23_vddio_cfg = { + .reg = &(((struct mxs_power_regs *)IMX_POWER_BASE)-> + hw_power_vddioctrl), + .step_mV = 25, + .lowest_mV = 2800, + .powered_by_linreg = mxs_get_vddio_power_source_off, + .trg_mask = POWER_VDDIOCTRL_TRG_MASK, + .bo_irq = POWER_CTRL_VDDIO_BO_IRQ, + .bo_enirq = POWER_CTRL_ENIRQ_VDDIO_BO, + .bo_offset_mask = POWER_VDDIOCTRL_BO_OFFSET_MASK, + .bo_offset_offset = POWER_VDDIOCTRL_BO_OFFSET_OFFSET, +}; + +static const struct mxs_vddx_cfg mx28_vddio_cfg = { + .reg = &(((struct mxs_power_regs *)IMX_POWER_BASE)-> + hw_power_vddioctrl), + .step_mV = 50, + .lowest_mV = 2800, + .powered_by_linreg = mxs_get_vddio_power_source_off, + .trg_mask = POWER_VDDIOCTRL_TRG_MASK, + .bo_irq = POWER_CTRL_VDDIO_BO_IRQ, + .bo_enirq = POWER_CTRL_ENIRQ_VDDIO_BO, + .bo_offset_mask = POWER_VDDIOCTRL_BO_OFFSET_MASK, + .bo_offset_offset = POWER_VDDIOCTRL_BO_OFFSET_OFFSET, +}; + +static const struct mxs_vddx_cfg mxs_vddd_cfg = { + .reg = &(((struct mxs_power_regs *)IMX_POWER_BASE)-> + hw_power_vdddctrl), + .step_mV = 25, + .lowest_mV = 800, + .powered_by_linreg = mxs_get_vddd_power_source_off, + .trg_mask = POWER_VDDDCTRL_TRG_MASK, + .bo_irq = POWER_CTRL_VDDD_BO_IRQ, + .bo_enirq = POWER_CTRL_ENIRQ_VDDD_BO, + .bo_offset_mask = POWER_VDDDCTRL_BO_OFFSET_MASK, + .bo_offset_offset = POWER_VDDDCTRL_BO_OFFSET_OFFSET, +}; + +static const struct mxs_vddx_cfg mxs_vddmem_cfg = { + .reg = &(((struct mxs_power_regs *)IMX_POWER_BASE)-> + hw_power_vddmemctrl), + .step_mV = 50, + .lowest_mV = 1700, + .powered_by_linreg = NULL, + .trg_mask = POWER_VDDMEMCTRL_TRG_MASK, + .bo_irq = 0, + .bo_enirq = 0, + .bo_offset_mask = 0, + .bo_offset_offset = 0, +}; + +/** + * mxs_power_set_vddx() - Configure voltage on DC-DC converter rail + * @cfg: Configuration data of the DC-DC converter rail + * @new_target: New target voltage of the DC-DC converter rail + * @new_brownout: New brownout trigger voltage + * + * This function configures the output voltage on the DC-DC converter rail. + * The rail is selected by the @cfg argument. The new voltage target is + * selected by the @new_target and the voltage is specified in mV. The + * new brownout value is selected by the @new_brownout argument and the + * value is also in mV. + */ +static void mxs_power_set_vddx(const struct mxs_vddx_cfg *cfg, + uint32_t new_target, uint32_t new_brownout) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + uint32_t cur_target, diff, bo_int = 0; + uint32_t powered_by_linreg = 0; + int adjust_up, tmp; + + new_brownout = DIV_ROUND_CLOSEST(new_target - new_brownout, cfg->step_mV); + + cur_target = readl(cfg->reg); + cur_target &= cfg->trg_mask; + cur_target *= cfg->step_mV; + cur_target += cfg->lowest_mV; + + adjust_up = new_target > cur_target; + if (cfg->powered_by_linreg) + powered_by_linreg = cfg->powered_by_linreg(); + + if (adjust_up && cfg->bo_irq) { + if (powered_by_linreg) { + bo_int = readl(cfg->reg); + clrbits_le32(cfg->reg, cfg->bo_enirq); + } + setbits_le32(cfg->reg, cfg->bo_offset_mask); + } + + do { + if (abs(new_target - cur_target) > 100) { + if (adjust_up) + diff = cur_target + 100; + else + diff = cur_target - 100; + } else { + diff = new_target; + } + + diff -= cfg->lowest_mV; + diff /= cfg->step_mV; + + clrsetbits_le32(cfg->reg, cfg->trg_mask, diff); + + if (powered_by_linreg || + (readl(&power_regs->hw_power_sts) & + POWER_STS_VDD5V_GT_VDDIO)) + mxs_early_delay(500); + else { + for (;;) { + tmp = readl(&power_regs->hw_power_sts); + if (tmp & POWER_STS_DC_OK) + break; + } + } + + cur_target = readl(cfg->reg); + cur_target &= cfg->trg_mask; + cur_target *= cfg->step_mV; + cur_target += cfg->lowest_mV; + } while (new_target > cur_target); + + if (cfg->bo_irq) { + if (adjust_up && powered_by_linreg) { + writel(cfg->bo_irq, &power_regs->hw_power_ctrl_clr); + if (bo_int & cfg->bo_enirq) + setbits_le32(cfg->reg, cfg->bo_enirq); + } + + clrsetbits_le32(cfg->reg, cfg->bo_offset_mask, + new_brownout << cfg->bo_offset_offset); + } +} + +/** + * mxs_setup_batt_detect() - Start the battery voltage measurement logic + * + * This function starts and configures the LRADC block. This allows the + * power initialization code to measure battery voltage and based on this + * knowledge, decide whether to boot at all, boot from battery or boot + * from 5V input. + */ +static void mxs_setup_batt_detect(void) +{ + mxs_lradc_init(); + mxs_lradc_enable_batt_measurement(); + mxs_early_delay(10); +} + +/** + * mx23_ungate_power() - Ungate the POWER block + * + * This function ungates clock to the power block. In case the power block + * was still gated at this point, it will not be possible to configure the + * block and therefore the power initialization would fail. This function + * is only needed on i.MX233, on i.MX28 the power block is always ungated. + */ +static void mx23_ungate_power(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + writel(MX23_POWER_CTRL_CLKGATE, &power_regs->hw_power_ctrl_clr); +} + +/** + * mx23_power_init() - The power block init main function + * + * This function calls all the power block initialization functions in + * proper sequence to start the power block. + */ +static void __mx23_power_init(int has_battery) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + mx23_ungate_power(); + + mxs_power_clock2xtal(); + mxs_power_set_auto_restart(); + mxs_power_set_linreg(); + mxs_power_setup_5v_detect(); + + mxs_setup_batt_detect(); + + mxs_src_power_init(); + + if (has_battery) + mxs_power_configure_power_source(); + else + mxs_enable_battery_input(); + + mxs_power_clock2pll(); + + mxs_init_batt_bo(); + + mxs_switch_vddd_to_dcdc_source(); + + /* Fire up the VDDMEM LinReg now that we're all set. */ + writel(POWER_VDDMEMCTRL_ENABLE_LINREG | POWER_VDDMEMCTRL_ENABLE_ILIMIT, + &power_regs->hw_power_vddmemctrl); + + mxs_enable_output_rail_protection(); + + mxs_power_set_vddx(&mx23_vddio_cfg, 3300, 3150); + mxs_power_set_vddx(&mxs_vddd_cfg, 1500, 1000); + mxs_power_set_vddx(&mxs_vddmem_cfg, 2500, 1700); + + writel(POWER_CTRL_VDDD_BO_IRQ | POWER_CTRL_VDDA_BO_IRQ | + POWER_CTRL_VDDIO_BO_IRQ | POWER_CTRL_VDD5V_DROOP_IRQ | + POWER_CTRL_VBUS_VALID_IRQ | POWER_CTRL_BATT_BO_IRQ | + POWER_CTRL_DCDC4P2_BO_IRQ, &power_regs->hw_power_ctrl_clr); + + writel(POWER_5VCTRL_PWDN_5VBRNOUT, &power_regs->hw_power_5vctrl_set); + + mxs_early_delay(1000); +} + +void mx23_power_init(void) +{ + __mx23_power_init(1); +} + +void mx23_power_init_battery_input(void) +{ + __mx23_power_init(0); +} + +/** + * mx28_power_init() - The power block init main function + * + * This function calls all the power block initialization functions in + * proper sequence to start the power block. + */ +static void __mx28_power_init(int has_battery) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + mxs_power_clock2xtal(); + mxs_power_set_auto_restart(); + mxs_power_set_linreg(); + mxs_power_setup_5v_detect(); + + mxs_setup_batt_detect(); + + mxs_src_power_init(); + + if (has_battery) + mxs_power_configure_power_source(); + else + mxs_enable_battery_input(); + + mxs_power_clock2pll(); + + mxs_init_batt_bo(); + + mxs_switch_vddd_to_dcdc_source(); + + mxs_enable_output_rail_protection(); + + mxs_power_set_vddx(&mx28_vddio_cfg, 3300, 3150); + mxs_power_set_vddx(&mxs_vddd_cfg, 1500, 1000); + + writel(POWER_CTRL_VDDD_BO_IRQ | POWER_CTRL_VDDA_BO_IRQ | + POWER_CTRL_VDDIO_BO_IRQ | POWER_CTRL_VDD5V_DROOP_IRQ | + POWER_CTRL_VBUS_VALID_IRQ | POWER_CTRL_BATT_BO_IRQ | + POWER_CTRL_DCDC4P2_BO_IRQ, &power_regs->hw_power_ctrl_clr); + + writel(POWER_5VCTRL_PWDN_5VBRNOUT, &power_regs->hw_power_5vctrl_set); + + mxs_early_delay(1000); +} + +void mx28_power_init(void) +{ + __mx28_power_init(1); +} + +void mx28_power_init_battery_input(void) +{ + __mx28_power_init(0); +} + +/** + * mxs_power_wait_pswitch() - Wait for power switch to be pressed + * + * This function waits until the power-switch was pressed to start booting + * the board. + */ +void mxs_power_wait_pswitch(void) +{ + struct mxs_power_regs *power_regs = + (struct mxs_power_regs *)IMX_POWER_BASE; + + while (!(readl(&power_regs->hw_power_sts) & POWER_STS_PSWITCH_MASK)) + ; +} |