diff options
Diffstat (limited to 'drivers/crypto/caam/regs.h')
-rw-r--r-- | drivers/crypto/caam/regs.h | 273 |
1 files changed, 219 insertions, 54 deletions
diff --git a/drivers/crypto/caam/regs.h b/drivers/crypto/caam/regs.h index 19e7d6d7e4..c2eea8d1a5 100644 --- a/drivers/crypto/caam/regs.h +++ b/drivers/crypto/caam/regs.h @@ -1,33 +1,94 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ /* * CAAM hardware register-level view * - * Copyright 2008-2015 Freescale Semiconductor, Inc. + * Copyright 2008-2011 Freescale Semiconductor, Inc. + * Copyright 2018 NXP */ #ifndef REGS_H #define REGS_H #include <linux/types.h> +#include <linux/bitops.h> #include <io.h> +#include <io-64-nonatomic-hi-lo.h> -extern bool caam_little_end; +/* + * Architecture-specific register access methods + * + * CAAM's bus-addressable registers are 64 bits internally. + * They have been wired to be safely accessible on 32-bit + * architectures, however. Registers were organized such + * that (a) they can be contained in 32 bits, (b) if not, then they + * can be treated as two 32-bit entities, or finally (c) if they + * must be treated as a single 64-bit value, then this can safely + * be done with two 32-bit cycles. + * + * For 32-bit operations on 64-bit values, CAAM follows the same + * 64-bit register access conventions as it's predecessors, in that + * writes are "triggered" by a write to the register at the numerically + * higher address, thus, a full 64-bit write cycle requires a write + * to the lower address, followed by a write to the higher address, + * which will latch/execute the write cycle. + * + * For example, let's assume a SW reset of CAAM through the master + * configuration register. + * - SWRST is in bit 31 of MCFG. + * - MCFG begins at base+0x0000. + * - Bits 63-32 are a 32-bit word at base+0x0000 (numerically-lower) + * - Bits 31-0 are a 32-bit word at base+0x0004 (numerically-higher) + * + * (and on Power, the convention is 0-31, 32-63, I know...) + * + * Assuming a 64-bit write to this MCFG to perform a software reset + * would then require a write of 0 to base+0x0000, followed by a + * write of 0x80000000 to base+0x0004, which would "execute" the + * reset. + * + * Of course, since MCFG 63-32 is all zero, we could cheat and simply + * write 0x8000000 to base+0x0004, and the reset would work fine. + * However, since CAAM does contain some write-and-read-intended + * 64-bit registers, this code defines 64-bit access methods for + * the sake of internal consistency and simplicity, and so that a + * clean transition to 64-bit is possible when it becomes necessary. + * + * There are limitations to this that the developer must recognize. + * 32-bit architectures cannot enforce an atomic-64 operation, + * Therefore: + * + * - On writes, since the HW is assumed to latch the cycle on the + * write of the higher-numeric-address word, then ordered + * writes work OK. + * + * - For reads, where a register contains a relevant value of more + * that 32 bits, the hardware employs logic to latch the other + * "half" of the data until read, ensuring an accurate value. + * This is of particular relevance when dealing with CAAM's + * performance counters. + * + */ -#define caam_to_cpu(len) \ -static inline u##len caam##len ## _to_cpu(u##len val) \ -{ \ - if (caam_little_end) \ - return le##len ## _to_cpu(val); \ - else \ - return be##len ## _to_cpu(val); \ +extern bool caam_little_end; +extern bool caam_imx; +extern size_t caam_ptr_sz; + +#define caam_to_cpu(len) \ +static inline u##len caam##len ## _to_cpu(u##len val) \ +{ \ + if (caam_little_end) \ + return le##len ## _to_cpu((__force __le##len)val); \ + else \ + return be##len ## _to_cpu((__force __be##len)val); \ } -#define cpu_to_caam(len) \ -static inline u##len cpu_to_caam##len(u##len val) \ -{ \ - if (caam_little_end) \ - return cpu_to_le##len(val); \ - else \ - return cpu_to_be##len(val); \ +#define cpu_to_caam(len) \ +static inline u##len cpu_to_caam##len(u##len val) \ +{ \ + if (caam_little_end) \ + return (__force u##len)cpu_to_le##len(val); \ + else \ + return (__force u##len)cpu_to_be##len(val); \ } caam_to_cpu(16) @@ -62,67 +123,95 @@ static inline void clrsetbits_32(void __iomem *reg, u32 clear, u32 set) } /* - * The DMA address registers in the JR are a pair of 32-bit registers. - * The layout is: + * The only users of these wr/rd_reg64 functions is the Job Ring (JR). + * The DMA address registers in the JR are handled differently depending on + * platform: + * + * 1. All BE CAAM platforms and i.MX platforms (LE CAAM): * * base + 0x0000 : most-significant 32 bits * base + 0x0004 : least-significant 32 bits * * The 32-bit version of this core therefore has to write to base + 0x0004 - * to set the 32-bit wide DMA address. This seems to be independent of the - * endianness of the written/read data. + * to set the 32-bit wide DMA address. + * + * 2. All other LE CAAM platforms (LS1021A etc.) + * base + 0x0000 : least-significant 32 bits + * base + 0x0004 : most-significant 32 bits */ - -#ifdef CONFIG_64BIT static inline void wr_reg64(void __iomem *reg, u64 data) { - if (caam_little_end) - iowrite64(data, reg); - else + if (caam_little_end) { + if (caam_imx) { + iowrite32(data >> 32, (u32 __iomem *)(reg)); + iowrite32(data, (u32 __iomem *)(reg) + 1); + } else { + iowrite64(data, reg); + } + } else { iowrite64be(data, reg); + } } -static inline void rd_reg64(void __iomem *reg) +static inline u64 rd_reg64(void __iomem *reg) { - if (caam_little_end) - ioread64(reg); - else - ioread64be(reg); + if (caam_little_end) { + if (caam_imx) { + u32 low, high; + + high = ioread32(reg); + low = ioread32(reg + sizeof(u32)); + + return low + ((u64)high << 32); + } else { + return ioread64(reg); + } + } else { + return ioread64be(reg); + } } -#else /* CONFIG_64BIT */ -static inline void wr_reg64(void __iomem *reg, u64 data) + +static inline u64 cpu_to_caam_dma64(dma_addr_t value) { - wr_reg32((u32 __iomem *)(reg), data >> 32); - wr_reg32((u32 __iomem *)(reg) + 1, data); + if (caam_imx) { + u64 ret_val = (u64)cpu_to_caam32(lower_32_bits(value)) << 32; + + if (IS_ENABLED(CONFIG_ARCH_DMA_ADDR_T_64BIT)) + ret_val |= (u64)cpu_to_caam32(upper_32_bits(value)); + + return ret_val; + } + + return cpu_to_caam64(value); } -static inline u64 rd_reg64(void __iomem *reg) +static inline u64 caam_dma64_to_cpu(u64 value) { - return ((u64)rd_reg32((u32 __iomem *)(reg)) << 32 | - (u64)rd_reg32((u32 __iomem *)(reg) + 1)); + if (caam_imx) + return (((u64)caam32_to_cpu(lower_32_bits(value)) << 32) | + (u64)caam32_to_cpu(upper_32_bits(value))); + + return caam64_to_cpu(value); } -#endif /* CONFIG_64BIT */ -static inline u64 cpu_to_caam_dma64(dma_addr_t value) +static inline u64 cpu_to_caam_dma(u64 value) { - return (((u64)cpu_to_caam32(lower_32_bits(value)) << 32) | - (u64)cpu_to_caam32(upper_32_bits(value))); + if (IS_ENABLED(CONFIG_ARCH_DMA_ADDR_T_64BIT) && + caam_ptr_sz == sizeof(u64)) + return cpu_to_caam_dma64(value); + else + return cpu_to_caam32(value); } -static inline u64 caam_dma64_to_cpu(u64 value) +static inline u64 caam_dma_to_cpu(u64 value) { - return (((u64)caam32_to_cpu(lower_32_bits(value)) << 32) | - (u64)caam32_to_cpu(upper_32_bits(value))); + if (IS_ENABLED(CONFIG_ARCH_DMA_ADDR_T_64BIT) && + caam_ptr_sz == sizeof(u64)) + return caam_dma64_to_cpu(value); + else + return caam32_to_cpu(value); } -#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT -#define cpu_to_caam_dma(value) cpu_to_caam_dma64(value) -#define caam_dma_to_cpu(value) caam_dma64_to_cpu(value) -#else -#define cpu_to_caam_dma(value) cpu_to_caam32(value) -#define caam_dma_to_cpu(value) caam32_to_cpu(value) -#endif /* CONFIG_ARCH_DMA_ADDR_T_64BIT */ - /* * jr_outentry * Represents each entry in a JobR output ring @@ -132,6 +221,66 @@ struct jr_outentry { u32 jrstatus; /* Status for completed descriptor */ } __packed; +static inline void jr_outentry_get(void *outring, int hw_idx, dma_addr_t *desc, + u32 *jrstatus) +{ + + if (caam_ptr_sz == sizeof(u32)) { + struct { + u32 desc; + u32 jrstatus; + } __packed *outentry = outring; + + *desc = outentry[hw_idx].desc; + *jrstatus = outentry[hw_idx].jrstatus; + } else { + struct { + dma_addr_t desc;/* Pointer to completed descriptor */ + u32 jrstatus; /* Status for completed descriptor */ + } __packed *outentry = outring; + + *desc = outentry[hw_idx].desc; + *jrstatus = outentry[hw_idx].jrstatus; + } +} + +#define SIZEOF_JR_OUTENTRY (caam_ptr_sz + sizeof(u32)) + +static inline dma_addr_t jr_outentry_desc(void *outring, int hw_idx) +{ + dma_addr_t desc; + u32 unused; + + jr_outentry_get(outring, hw_idx, &desc, &unused); + + return desc; +} + +static inline u32 jr_outentry_jrstatus(void *outring, int hw_idx) +{ + dma_addr_t unused; + u32 jrstatus; + + jr_outentry_get(outring, hw_idx, &unused, &jrstatus); + + return jrstatus; +} + +static inline void jr_inpentry_set(void *inpring, int hw_idx, dma_addr_t val) +{ + if (caam_ptr_sz == sizeof(u32)) { + u32 *inpentry = inpring; + + inpentry[hw_idx] = val; + } else { + dma_addr_t *inpentry = inpring; + + inpentry[hw_idx] = val; + } +} + +#define SIZEOF_JR_INPENTRY caam_ptr_sz + /* * CHA version ID / instantiation bitfields * Defined for use within cha_id in perfmon @@ -282,6 +431,7 @@ struct caam_perfmon { #define CRNR_LS_RNGRN_SHIFT 16 #define CRNR_LS_RNGRN_MASK (0xfull << CRNR_LS_RNGRN_SHIFT) u32 cha_rev_ls; /* CRNR - CHA Rev No. Least significant half*/ +#define CTPR_MS_PS BIT(17) #define CTPR_MS_QI_SHIFT 25 #define CTPR_MS_QI_MASK (0x1ull << CTPR_MS_QI_SHIFT) #define CTPR_MS_VIRT_EN_INCL 0x00000001 @@ -433,7 +583,10 @@ struct rngtst { /* RNG4 TRNG test registers */ struct rng4tst { -#define RTMCTL_PRGM 0x00010000 /* 1 -> program mode, 0 -> run mode */ +#define RTMCTL_ACC BIT(5) /* TRNG access mode */ +#define RTMCTL_FCT_FAIL BIT(8) +#define RTMCTL_ERR BIT(12) +#define RTMCTL_PRGM BIT(16) /* 1 -> program mode, 0 -> run mode */ #define RTMCTL_SAMP_MODE_VON_NEUMANN_ES_SC 0 /* use von Neumann data in both entropy shifter and statistical checker */ @@ -444,6 +597,7 @@ struct rng4tst { entropy shifter, raw data in statistical checker */ #define RTMCTL_SAMP_MODE_INVALID 3 /* invalid combination */ +#define RTMCTL_SAMP_MODE_MASK 3 u32 rtmctl; /* misc. control register */ u32 rtscmisc; /* statistical check misc. register */ u32 rtpkrrng; /* poker range register */ @@ -466,12 +620,23 @@ struct rng4tst { u32 rtfrqmax; /* PRGM=1: freq. count max. limit register */ u32 rtfrqcnt; /* PRGM=0: freq. count register */ }; - u32 rsvd1[40]; + u32 rtscml; + u32 rtscr1l; + u32 rtscr2l; + u32 rtscr3l; + u32 rtscr4l; + u32 rtscr5l; + u32 rtscr6pl; + u32 rtstatus; + u32 rsvd1[32]; #define RDSTA_SKVT 0x80000000 #define RDSTA_SKVN 0x40000000 +#define RDSTA_PR0 BIT(4) +#define RDSTA_PR1 BIT(5) #define RDSTA_IF0 0x00000001 #define RDSTA_IF1 0x00000002 #define RDSTA_IFMASK (RDSTA_IF1 | RDSTA_IF0) +#define RDSTA_MASK (RDSTA_PR1 | RDSTA_PR0 | RDSTA_IF1 | RDSTA_IF0) u32 rdsta; u32 rsvd2[15]; }; |