1 files changed, 0 insertions, 139 deletions
diff --git a/dts/Bindings/bus/ti-sysc.txt b/dts/Bindings/bus/ti-sysc.txt
deleted file mode 100644
index c984143d08..0000000000
--- a/dts/Bindings/bus/ti-sysc.txt
+++ /dev/null
@@ -1,139 +0,0 @@
-Texas Instruments sysc interconnect target module wrapper binding
-
-Texas Instruments SoCs can have a generic interconnect target module
-hardware for devices connected to various interconnects such as L3
-interconnect (Arteris NoC) and L4 interconnect (Sonics s3220). The sysc
-is mostly used for interaction between module and PRCM. It participates
-in the OCP Disconnect Protocol but other than that is mostly independent
-of the interconnect.
-
-Each interconnect target module can have one or more devices connected to
-it. There is a set of control registers for managing interconnect target
-module clocks, idle modes and interconnect level resets for the module.
-
-These control registers are sprinkled into the unused register address
-space of the first child device IP block managed by the interconnect
-target module and typically are named REVISION, SYSCONFIG and SYSSTATUS.
-
-Required standard properties:
-
-- compatible	shall be one of the following generic types:
-
-		"ti,sysc"
-		"ti,sysc-omap2"
-		"ti,sysc-omap4"
-		"ti,sysc-omap4-simple"
-
-		or one of the following derivative types for hardware
-		needing special workarounds:
-
-		"ti,sysc-omap2-timer"
-		"ti,sysc-omap4-timer"
-		"ti,sysc-omap3430-sr"
-		"ti,sysc-omap3630-sr"
-		"ti,sysc-omap4-sr"
-		"ti,sysc-omap3-sham"
-		"ti,sysc-omap-aes"
-		"ti,sysc-mcasp"
-		"ti,sysc-dra7-mcasp"
-		"ti,sysc-usb-host-fs"
-		"ti,sysc-dra7-mcan"
-		"ti,sysc-pruss"
-
-- reg		shall have register areas implemented for the interconnect
-		target module in question such as revision, sysc and syss
-
-- reg-names	shall contain the register names implemented for the
-		interconnect target module in question such as
-		"rev, "sysc", and "syss"
-
-- ranges	shall contain the interconnect target module IO range
-		available for one or more child device IP blocks managed
-		by the interconnect target module, the ranges may include
-		multiple ranges such as device L4 range for control and
-		parent L3 range for DMA access
-
-Optional properties:
-
-- ti,sysc-mask	shall contain mask of supported register bits for the
-		SYSCONFIG register as documented in the Technical Reference
-		Manual (TRM) for the interconnect target module
-
-- ti,sysc-midle	list of master idle modes supported by the interconnect
-		target module as documented in the TRM for SYSCONFIG
-		register MIDLEMODE bits
-
-- ti,sysc-sidle	list of slave idle modes supported by the interconnect
-		target module as documented in the TRM for SYSCONFIG
-		register SIDLEMODE bits
-
-- ti,sysc-delay-us	delay needed after OCP softreset before accssing
-			SYSCONFIG register again
-
-- ti,syss-mask	optional mask of reset done status bits as described in the
-		TRM for SYSSTATUS registers, typically 1 with some devices
-		having separate reset done bits for children like OHCI and
-		EHCI
-
-- clocks	clock specifier for each name in the clock-names as
-		specified in the binding documentation for ti-clkctrl,
-		typically available for all interconnect targets on TI SoCs
-		based on omap4 except if it's read-only register in hwauto
-		mode as for example omap4 L4_CFG_CLKCTRL
-
-- clock-names	should contain at least "fck", and optionally also "ick"
-		depending on the SoC and the interconnect target module,
-		some interconnect target modules also need additional
-		optional clocks that can be specified as listed in TRM
-		for the related CLKCTRL register bits 8 to 15 such as
-		"dbclk" or "clk32k" depending on their role
-
-- ti,hwmods	optional TI interconnect module name to use legacy
-		hwmod platform data
-
-- ti,no-reset-on-init	interconnect target module should not be reset at init
-
-- ti,no-idle-on-init	interconnect target module should not be idled at init
-
-- ti,no-idle		interconnect target module should not be idled
-
-Example: Single instance of MUSB controller on omap4 using interconnect ranges
-using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000):
-
-	target-module@2b000 {		/* 0x4a0ab000, ap 84 12.0 */
-		compatible = "ti,sysc-omap2";
-		ti,hwmods = "usb_otg_hs";
-		reg = <0x2b400 0x4>,
-		      <0x2b404 0x4>,
-		      <0x2b408 0x4>;
-		reg-names = "rev", "sysc", "syss";
-		clocks = <&l3_init_clkctrl OMAP4_USB_OTG_HS_CLKCTRL 0>;
-		clock-names = "fck";
-		ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP |
-				 SYSC_OMAP2_SOFTRESET |
-				 SYSC_OMAP2_AUTOIDLE)>;
-		ti,sysc-midle = <SYSC_IDLE_FORCE>,
-				<SYSC_IDLE_NO>,
-				<SYSC_IDLE_SMART>;
-		ti,sysc-sidle = <SYSC_IDLE_FORCE>,
-				<SYSC_IDLE_NO>,
-				<SYSC_IDLE_SMART>,
-				<SYSC_IDLE_SMART_WKUP>;
-		ti,syss-mask = <1>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0 0x2b000 0x1000>;
-
-		usb_otg_hs: otg@0 {
-			compatible = "ti,omap4-musb";
-			reg = <0x0 0x7ff>;
-			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
-			usb-phy = <&usb2_phy>;
-			...
-		};
-	};
-
-Note that other SoCs, such as am335x can have multiple child devices. On am335x
-there are two MUSB instances, two USB PHY instances, and a single CPPI41 DMA
-instance as children of a single interconnect target module.