diff options
Diffstat (limited to 'dts/Bindings/connector')
| -rw-r--r-- | dts/Bindings/connector/samsung,usb-connector-11pin.txt | 49 | ||||
| -rw-r--r-- | dts/Bindings/connector/usb-connector.txt | 135 | ||||
| -rw-r--r-- | dts/Bindings/connector/usb-connector.yaml | 480 |
3 files changed, 480 insertions, 184 deletions
diff --git a/dts/Bindings/connector/samsung,usb-connector-11pin.txt b/dts/Bindings/connector/samsung,usb-connector-11pin.txt deleted file mode 100644 index 22256e295a..0000000000 --- a/dts/Bindings/connector/samsung,usb-connector-11pin.txt +++ /dev/null @@ -1,49 +0,0 @@ -Samsung micro-USB 11-pin connector -================================== - -Samsung micro-USB 11-pin connector is an extension of micro-USB connector. -It is present in multiple Samsung mobile devices. -It has additional pins to route MHL traffic simultanously with USB. - -The bindings are superset of usb-connector bindings for micro-USB connector[1]. - -Required properties: -- compatible: must be: "samsung,usb-connector-11pin", "usb-b-connector", -- type: must be "micro". - -Required nodes: -- any data bus to the connector should be modeled using the OF graph bindings - specified in bindings/graph.txt, unless the bus is between parent node and - the connector. Since single connector can have multpile data buses every bus - has assigned OF graph port number as follows: - 0: High Speed (HS), - 3: Mobile High-Definition Link (MHL), specific to 11-pin Samsung micro-USB. - -[1]: bindings/connector/usb-connector.txt - -Example -------- - -Micro-USB connector with HS lines routed via controller (MUIC) and MHL lines -connected to HDMI-MHL bridge (sii8620): - -muic-max77843@66 { - ... - usb_con: connector { - compatible = "samsung,usb-connector-11pin", "usb-b-connector"; - label = "micro-USB"; - type = "micro"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@3 { - reg = <3>; - usb_con_mhl: endpoint { - remote-endpoint = <&sii8620_mhl>; - }; - }; - }; - }; -}; diff --git a/dts/Bindings/connector/usb-connector.txt b/dts/Bindings/connector/usb-connector.txt deleted file mode 100644 index 88578ac1a8..0000000000 --- a/dts/Bindings/connector/usb-connector.txt +++ /dev/null @@ -1,135 +0,0 @@ -USB Connector -============= - -A USB connector node represents a physical USB connector. It should be -a child of a USB interface controller. - -Required properties: -- compatible: describes type of the connector, must be one of: - "usb-a-connector", - "usb-b-connector", - "usb-c-connector". - -Optional properties: -- label: symbolic name for the connector, -- type: size of the connector, should be specified in case of USB-A, USB-B - non-fullsize connectors: "mini", "micro". -- self-powered: Set this property if the usb device that has its own power - source. - -Optional properties for usb-b-connector: -- id-gpios: an input gpio for USB ID pin. -- vbus-gpios: an input gpio for USB VBUS pin, used to detect presence of - VBUS 5V. - see gpio/gpio.txt. -- vbus-supply: a phandle to the regulator for USB VBUS if needed when host - mode or dual role mode is supported. - Particularly, if use an output GPIO to control a VBUS regulator, should - model it as a regulator. - see regulator/fixed-regulator.yaml -- pinctrl-names : a pinctrl state named "default" is optional -- pinctrl-0 : pin control group - see pinctrl/pinctrl-bindings.txt - -Optional properties for usb-c-connector: -- power-role: should be one of "source", "sink" or "dual"(DRP) if typec - connector has power support. -- try-power-role: preferred power role if "dual"(DRP) can support Try.SNK - or Try.SRC, should be "sink" for Try.SNK or "source" for Try.SRC. -- data-role: should be one of "host", "device", "dual"(DRD) if typec - connector supports USB data. - -Required properties for usb-c-connector with power delivery support: -- source-pdos: An array of u32 with each entry providing supported power - source data object(PDO), the detailed bit definitions of PDO can be found - in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2 - Source_Capabilities Message, the order of each entry(PDO) should follow - the PD spec chapter 6.4.1. Required for power source and power dual role. - User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() - defined in dt-bindings/usb/pd.h. -- sink-pdos: An array of u32 with each entry providing supported power - sink data object(PDO), the detailed bit definitions of PDO can be found - in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3 - Sink Capabilities Message, the order of each entry(PDO) should follow - the PD spec chapter 6.4.1. Required for power sink and power dual role. - User can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined - in dt-bindings/usb/pd.h. -- op-sink-microwatt: Sink required operating power in microwatt, if source - can't offer the power, Capability Mismatch is set. Required for power - sink and power dual role. - -Required nodes: -- any data bus to the connector should be modeled using the OF graph bindings - specified in bindings/graph.txt, unless the bus is between parent node and - the connector. Since single connector can have multiple data buses every bus - has assigned OF graph port number as follows: - 0: High Speed (HS), present in all connectors, - 1: Super Speed (SS), present in SS capable connectors, - 2: Sideband use (SBU), present in USB-C. - -Examples --------- - -1. Micro-USB connector with HS lines routed via controller (MUIC): - -muic-max77843@66 { - ... - usb_con: connector { - compatible = "usb-b-connector"; - label = "micro-USB"; - type = "micro"; - }; -}; - -2. USB-C connector attached to CC controller (s2mm005), HS lines routed -to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort. -DisplayPort video lines are routed to the connector via SS mux in USB3 PHY. - -ccic: s2mm005@33 { - ... - usb_con: connector { - compatible = "usb-c-connector"; - label = "USB-C"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - usb_con_hs: endpoint { - remote-endpoint = <&max77865_usbc_hs>; - }; - }; - port@1 { - reg = <1>; - usb_con_ss: endpoint { - remote-endpoint = <&usbdrd_phy_ss>; - }; - }; - port@2 { - reg = <2>; - usb_con_sbu: endpoint { - remote-endpoint = <&dp_aux>; - }; - }; - }; - }; -}; - -3. USB-C connector attached to a typec port controller(ptn5110), which has -power delivery support and enables drp. - -typec: ptn5110@50 { - ... - usb_con: connector { - compatible = "usb-c-connector"; - label = "USB-C"; - power-role = "dual"; - try-power-role = "sink"; - source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; - sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) - PDO_VAR(5000, 12000, 2000)>; - op-sink-microwatt = <10000000>; - }; -}; diff --git a/dts/Bindings/connector/usb-connector.yaml b/dts/Bindings/connector/usb-connector.yaml new file mode 100644 index 0000000000..fb216ce68b --- /dev/null +++ b/dts/Bindings/connector/usb-connector.yaml @@ -0,0 +1,480 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/connector/usb-connector.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB Connector + +maintainers: + - Rob Herring <robh@kernel.org> + +description: + A USB connector node represents a physical USB connector. It should be a child + of a USB interface controller or a separate node when it is attached to both + MUX and USB interface controller. + +properties: + compatible: + oneOf: + - enum: + - usb-a-connector + - usb-b-connector + - usb-c-connector + + - items: + - const: gpio-usb-b-connector + - const: usb-b-connector + + - items: + - const: samsung,usb-connector-11pin + - const: usb-b-connector + + reg: + maxItems: 1 + + label: + description: Symbolic name for the connector. + + type: + description: Size of the connector, should be specified in case of + non-fullsize 'usb-a-connector' or 'usb-b-connector' compatible + connectors. + $ref: /schemas/types.yaml#/definitions/string + + enum: + - mini + - micro + + self-powered: + description: Set this property if the USB device has its own power source. + type: boolean + + # The following are optional properties for "usb-b-connector". + id-gpios: + description: An input gpio for USB ID pin. + maxItems: 1 + + vbus-gpios: + description: An input gpio for USB VBus pin, used to detect presence of + VBUS 5V. + maxItems: 1 + + vbus-supply: + description: A phandle to the regulator for USB VBUS if needed when host + mode or dual role mode is supported. + Particularly, if use an output GPIO to control a VBUS regulator, should + model it as a regulator. See bindings/regulator/fixed-regulator.yaml + + power-role: + description: Determines the power role that the Type C connector will + support. "dual" refers to Dual Role Port (DRP). + $ref: /schemas/types.yaml#/definitions/string + + enum: + - source + - sink + - dual + + try-power-role: + description: Preferred power role. + $ref: /schemas/types.yaml#/definitions/string + + enum: + - source + - sink + - dual + + data-role: + description: Data role if Type C connector supports USB data. "dual" refers + Dual Role Device (DRD). + $ref: /schemas/types.yaml#/definitions/string + + enum: + - host + - device + - dual + + typec-power-opmode: + description: Determines the power operation mode that the Type C connector + will support and will advertise through CC pins when it has no power + delivery support. + - "default" corresponds to default USB voltage and current defined by the + USB 2.0 and USB 3.2 specifications, 5V 500mA for USB 2.0 ports and + 5V 900mA or 1500mA for USB 3.2 ports in single-lane or dual-lane + operation respectively. + - "1.5A" and "3.0A", 5V 1.5A and 5V 3.0A respectively, as defined in USB + Type-C Cable and Connector specification, when Power Delivery is not + supported. + $ref: /schemas/types.yaml#/definitions/string + enum: + - default + - 1.5A + - 3.0A + + pd-disable: + description: Set this property if the Type-C connector has no power delivery support. + type: boolean + + # The following are optional properties for "usb-c-connector" with power + # delivery support. + sink-vdos: + description: An array of u32 with each entry, a Vendor Defined Message Object (VDO), + providing additional information corresponding to the product, the detailed bit + definitions and the order of each VDO can be found in + "USB Power Delivery Specification Revision 3.0, Version 2.0 + ECNs 2020-12-10" + chapter 6.4.4.3.1 Discover Identity. User can specify the VDO array via + VDO_IDH/_CERT/_PRODUCT/_UFP/_DFP/_PCABLE/_ACABLE(1/2)/_VPD() defined in + dt-bindings/usb/pd.h. + minItems: 3 + maxItems: 6 + $ref: /schemas/types.yaml#/definitions/uint32-array + + sink-vdos-v1: + description: An array of u32 with each entry, a Vendor Defined Message Object (VDO), + providing additional information corresponding to the product, the detailed bit + definitions and the order of each VDO can be found in + "USB Power Delivery Specification Revision 2.0, Version 1.3" chapter 6.4.4.3.1 Discover + Identity. User can specify the VDO array via VDO_IDH/_CERT/_PRODUCT/_CABLE/_AMA defined in + dt-bindings/usb/pd.h. + minItems: 3 + maxItems: 6 + $ref: /schemas/types.yaml#/definitions/uint32-array + + accessory-mode-audio: + type: boolean + description: Whether the device supports Audio Adapter Accessory Mode. This + is only necessary if there are no other means to discover supported + alternative modes (e.g. through the UCSI firmware interface). + + accessory-mode-debug: + type: boolean + description: Whether the device supports Debug Accessory Mode. This + is only necessary if there are no other means to discover supported + alternative modes (e.g. through the UCSI firmware interface). + + altmodes: + type: object + description: List of Alternative Modes supported by the schematics on the + particular device. This is only necessary if there are no other means to + discover supported alternative modes (e.g. through the UCSI firmware + interface). + + additionalProperties: false + + patternProperties: + "^(displayport)$": + type: object + description: + A single USB-C Alternative Mode as supported by the USB-C connector logic. + + additionalProperties: false + + properties: + svid: + $ref: /schemas/types.yaml#/definitions/uint16 + description: Unique value assigned by USB-IF to the Vendor / AltMode. + enum: [ 0xff01 ] + vdo: + $ref: /schemas/types.yaml#/definitions/uint32 + description: VDO returned by Discover Modes USB PD command. + + port: + $ref: /schemas/graph.yaml#/properties/port + description: OF graph bindings modeling a data bus to the connector, e.g. + there is a single High Speed (HS) port present in this connector. If there + is more than one bus (several port, with 'reg' property), they can be grouped + under 'ports'. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: OF graph bindings modeling any data bus to the connector + unless the bus is between parent node and the connector. Since a single + connector can have multiple data buses every bus has an assigned OF graph + port number as described below. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: High Speed (HS), present in all connectors. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Super Speed (SS), present in SS capable connectors. + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: Sideband Use (SBU), present in USB-C. This describes the + alternate mode connection of which SBU is a part. + + required: + - port@0 + + new-source-frs-typec-current: + description: Initial current capability of the new source when vSafe5V + is applied during PD3.0 Fast Role Swap. "Table 6-14 Fixed Supply PDO - Sink" + of "USB Power Delivery Specification Revision 3.0, Version 1.2" provides the + different power levels and "6.4.1.3.1.6 Fast Role Swap USB Type-C Current" + provides a detailed description of the field. The sink PDO from current source + reflects the current source's(i.e. transmitter of the FRS signal) power + requirement during fr swap. The current sink (i.e. receiver of the FRS signal), + a.k.a new source, should check if it will be able to satisfy the current source's, + new sink's, requirement during frswap before enabling the frs signal reception. + This property refers to maximum current capability that the current sink can + satisfy. During FRS, VBUS voltage is at 5V, as the partners are in implicit + contract, hence, the power level is only a function of the current capability. + "1" refers to default USB power level as described by "Table 6-14 Fixed Supply PDO - Sink". + "2" refers to 1.5A@5V. + "3" refers to 3.0A@5V. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 3] + + slow-charger-loop: + description: Allows PMIC charger loops which are slow(i.e. cannot meet the 15ms deadline) to + still comply to pSnkStby i.e Maximum power that can be consumed by sink while in Sink Standby + state as defined in 7.4.2 Sink Electrical Parameters of USB Power Delivery Specification + Revision 3.0, Version 1.2. When the property is set, the port requests pSnkStby(2.5W - + 5V@500mA) upon entering SNK_DISCOVERY(instead of 3A or the 1.5A, Rp current advertised, during + SNK_DISCOVERY) and the actual current limit after reception of PS_Ready for PD link or during + SNK_READY for non-pd link. + type: boolean + + capabilities: + description: A child node to contain all the selectable USB Power Delivery capabilities. + type: object + + patternProperties: + "^caps-[0-9]+$": + description: Child nodes under "capabilities" node. Each node contains a selectable USB + Power Delivery capability. + type: object + $ref: "#/$defs/capabilities" + unevaluatedProperties: false + + additionalProperties: false + +dependencies: + sink-vdos-v1: [ sink-vdos ] + sink-vdos: [ sink-vdos-v1 ] + +required: + - compatible + +$defs: + capabilities: + type: object + + properties: + source-pdos: + description: An array of u32 with each entry providing supported power + source data object(PDO), the detailed bit definitions of PDO can be found + in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2 + Source_Capabilities Message, the order of each entry(PDO) should follow + the PD spec chapter 6.4.1. Required for power source and power dual role. + User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() + defined in dt-bindings/usb/pd.h. + minItems: 1 + maxItems: 7 + $ref: /schemas/types.yaml#/definitions/uint32-array + + sink-pdos: + description: An array of u32 with each entry providing supported power sink + data object(PDO), the detailed bit definitions of PDO can be found in + "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3 + Sink Capabilities Message, the order of each entry(PDO) should follow the + PD spec chapter 6.4.1. Required for power sink and power dual role. User + can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined + in dt-bindings/usb/pd.h. + minItems: 1 + maxItems: 7 + $ref: /schemas/types.yaml#/definitions/uint32-array + + op-sink-microwatt: + description: Sink required operating power in microwatt, if source can't + offer the power, Capability Mismatch is set. Required for power sink and + power dual role. + +allOf: + - $ref: "#/$defs/capabilities" + - if: + properties: + compatible: + contains: + const: gpio-usb-b-connector + then: + anyOf: + - required: + - vbus-gpios + - required: + - id-gpios + + - if: + properties: + compatible: + contains: + const: samsung,usb-connector-11pin + then: + properties: + type: + const: micro + +anyOf: + - not: + required: + - typec-power-opmode + - new-source-frs-typec-current + +unevaluatedProperties: false + +examples: + # Micro-USB connector with HS lines routed via controller (MUIC). + - | + muic-max77843 { + usb_con1: connector { + compatible = "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + }; + }; + + # USB-C connector attached to CC controller (s2mm005), HS lines routed + # to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort. + # DisplayPort video lines are routed to the connector via SS mux in USB3 PHY. + - | + ccic: s2mm005 { + usb_con2: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + + altmodes { + displayport { + svid = /bits/ 16 <0xff01>; + vdo = <0x00001c46>; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + usb_con_hs: endpoint { + remote-endpoint = <&max77865_usbc_hs>; + }; + }; + port@1 { + reg = <1>; + usb_con_ss: endpoint { + remote-endpoint = <&usbdrd_phy_ss>; + }; + }; + port@2 { + reg = <2>; + usb_con_sbu: endpoint { + remote-endpoint = <&dp_aux>; + }; + }; + }; + }; + }; + + # USB-C connector attached to a typec port controller(ptn5110), which has + # power delivery support and enables drp. + - | + #include <dt-bindings/usb/pd.h> + typec: ptn5110 { + usb_con3: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 12000, 2000)>; + op-sink-microwatt = <10000000>; + }; + }; + + # USB-C connector attached to SoC with a single High-Speed controller + - | + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + + port { + high_speed_ep: endpoint { + remote-endpoint = <&usb_hs_ep>; + }; + }; + }; + + # USB-C connector attached to SoC and USB3 typec port controller(hd3ss3220) + # with SS 2:1 MUX. HS lines routed to SoC, SS lines routed to the MUX and + # the output of MUX is connected to the SoC. + - | + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + hs_ep: endpoint { + remote-endpoint = <&usb3_hs_ep>; + }; + }; + port@1 { + reg = <1>; + ss_ep: endpoint { + remote-endpoint = <&hd3ss3220_in_ep>; + }; + }; + }; + }; + + # USB connector with GPIO control lines + - | + #include <dt-bindings/gpio/gpio.h> + + usb { + connector { + compatible = "gpio-usb-b-connector", "usb-b-connector"; + type = "micro"; + id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>; + vbus-supply = <&usb_p0_vbus>; + }; + }; + + # Micro-USB connector with HS lines routed via controller (MUIC) and MHL + # lines connected to HDMI-MHL bridge (sii8620) on Samsung Exynos5433-based + # mobile phone + - | + muic-max77843 { + usb_con4: connector { + compatible = "samsung,usb-connector-11pin", "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + muic_to_usb: endpoint { + remote-endpoint = <&usb_to_muic>; + }; + }; + port@3 { + reg = <3>; + usb_con_mhl: endpoint { + remote-endpoint = <&sii8620_mhl>; + }; + }; + }; + }; + }; |