diff options
Diffstat (limited to 'dts/Bindings/display/atmel,lcdc.txt')
| -rw-r--r-- | dts/Bindings/display/atmel,lcdc.txt | 89 |
1 files changed, 89 insertions, 0 deletions
diff --git a/dts/Bindings/display/atmel,lcdc.txt b/dts/Bindings/display/atmel,lcdc.txt new file mode 100644 index 0000000000..ecb8da063d --- /dev/null +++ b/dts/Bindings/display/atmel,lcdc.txt @@ -0,0 +1,89 @@ +Atmel LCDC Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : + "atmel,at91sam9261-lcdc" , + "atmel,at91sam9263-lcdc" , + "atmel,at91sam9g10-lcdc" , + "atmel,at91sam9g45-lcdc" , + "atmel,at91sam9g45es-lcdc" , + "atmel,at91sam9rl-lcdc" , + "atmel,at32ap-lcdc" +- reg : Should contain 1 register ranges(address and length). + Can contain an additional register range(address and length) + for fixed framebuffer memory. Useful for dedicated memories. +- interrupts : framebuffer controller interrupt +- display: a phandle pointing to the display node + +Required nodes: +- display: a display node is required to initialize the lcd panel + This should be in the board dts. +- default-mode: a videomode within the display with timing parameters + as specified below. + +Optional properties: +- lcd-supply: Regulator for LCD supply voltage. + +Example: + + fb0: fb@0x00500000 { + compatible = "atmel,at91sam9g45-lcdc"; + reg = <0x00500000 0x1000>; + interrupts = <23 3 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fb>; + display = <&display0>; + status = "okay"; + #address-cells = <1>; + #size-cells = <1>; + + }; + +Example for fixed framebuffer memory: + + fb0: fb@0x00500000 { + compatible = "atmel,at91sam9263-lcdc"; + reg = <0x00700000 0x1000 0x70000000 0x200000>; + [...] + }; + +Atmel LCDC Display +----------------------------------------------------- +Required properties (as per of_videomode_helper): + + - atmel,dmacon: dma controller configuration + - atmel,lcdcon2: lcd controller configuration + - atmel,guard-time: lcd guard time (Delay in frame periods) + - bits-per-pixel: lcd panel bit-depth. + +Optional properties (as per of_videomode_helper): + - atmel,lcdcon-backlight: enable backlight + - atmel,lcdcon-backlight-inverted: invert backlight PWM polarity + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG" + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed) + +Example: + display0: display { + bits-per-pixel = <32>; + atmel,lcdcon-backlight; + atmel,dmacon = <0x1>; + atmel,lcdcon2 = <0x80008002>; + atmel,guard-time = <9>; + atmel,lcd-wiring-mode = <1>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hback-porch = <1>; + hfront-porch = <1>; + vback-porch = <40>; + vfront-porch = <1>; + hsync-len = <45>; + vsync-len = <1>; + }; + }; + }; |