diff options
Diffstat (limited to 'dts/Bindings/display/panel/panel-edp.yaml')
| -rw-r--r-- | dts/Bindings/display/panel/panel-edp.yaml | 188 |
1 files changed, 188 insertions, 0 deletions
diff --git a/dts/Bindings/display/panel/panel-edp.yaml b/dts/Bindings/display/panel/panel-edp.yaml new file mode 100644 index 0000000000..bb0cf6827e --- /dev/null +++ b/dts/Bindings/display/panel/panel-edp.yaml @@ -0,0 +1,188 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/panel-edp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Probeable (via DP AUX / EDID) eDP Panels with simple poweron sequences + +maintainers: + - Douglas Anderson <dianders@chromium.org> + +description: | + This binding file can be used to indicate that an eDP panel is connected + to a Embedded DisplayPort AUX bus (see display/dp-aux-bus.yaml) without + actually specifying exactly what panel is connected. This is useful for + the case that more than one different panel could be connected to the + board, either for second-sourcing purposes or to support multiple SKUs + with different LCDs that hook up to a common board. + + As per above, a requirement for using this binding is that the panel is + represented under the DP AUX bus. This means that we can use any + information provided by the DP AUX bus (including the EDID) to identify + the panel. We can use this to identify display size, resolution, and + timings among other things. + + One piece of information about eDP panels that is typically _not_ + provided anywhere on the DP AUX bus is the power sequencing timings. + This is the reason why, historically, we've always had to explicitly + list eDP panels. We solve that here with two tricks. The "worst case" + power on timings for any panels expected to be connected to a board are + specified in these bindings. Once we've powered on, it's expected that + the operating system will lookup the panel in a table (based on EDID + information) to figure out other power sequencing timings. + + eDP panels in general can have somewhat arbitrary power sequencing + requirements. However, even though it's arbitrary in general, the + vast majority of panel datasheets have a power sequence diagram that + looks the exactly the same as every other panel. Each panel datasheet + cares about different timings in this diagram but the fact that the + diagram is so similar means we can come up with a single driver to + handle it. + + These diagrams all look roughly like this, sometimes labeled with + slightly different numbers / lines but all pretty much the same + sequence. This is because much of this diagram comes straight from + the eDP Standard. + + __________________________________________________ + Vdd ___/: :\____ / + _/ : : \_____/ + :<T1>:<T2>: :<--T10-->:<T11>:<T12>: + : +-----------------------+---------+---------+ + eDP -----------+ Black video | Src vid | Blk vid + + Display : +-----------------------+---------+---------+ + : _______________________:_________:_________: + HPD :<T3>| : : | + ___________| : : |_____________ + : : : : + Sink +-----------------------:---------:---------+ + AUX CH -----------+ AUX Ch operational : : +------------- + +-----------------------:---------:---------+ + : : : : + :<T4>: :<T7>: : : + Src main +------+------+--------------+---------+ + lnk data----------------+LnkTrn| Idle |Valid vid data| Idle/off+------------- + +------+------+--------------+---------+ + : <T5> :<-T6->:<-T8->: : + :__:<T9>: + LED_EN | | + _____________________________________| |____________________________ + : : + __________:__:_ + PWM | : : | + __________________________| : : |__________________________ + : : : : + _____________:__________:__:_:______ + Bklight ____/: : : : : :\____ + power _______/ :<---T13---->: : : :<T16>: \______________ + (Vbl) :<T17>:<---------T14--------->: :<-T15->:<T18>: + + The above looks fairly complex but, as per above, each panel only cares + about a subset of those timings. + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + const: edp-panel + + hpd-reliable-delay-ms: + description: + A fixed amount of time that must be waited after powering on the + panel's power-supply before the HPD signal is a reliable way to know + when the AUX channel is ready. This is useful for panels that glitch + the HPD at the start of power-on. This value is not needed if HPD is + always reliable for all panels that might be connected. + + hpd-absent-delay-ms: + description: + The panel specifies that HPD will be asserted this many milliseconds + from power on (timing T3 in the diagram above). If we have no way to + measure HPD then a fixed delay of this many milliseconds can be used. + This can also be used as a timeout when waiting for HPD. Does not + include the hpd-reliable-delay, so if hpd-reliable-delay was 80 ms + and hpd-absent-delay was 200 ms then we'd do a fixed 80 ms delay and + then we know HPD would assert in the next 120 ms. This value is not + needed if HPD hooked up, either through a GPIO in the panel node or + hooked up directly to the eDP controller. + + backlight: true + enable-gpios: true + port: true + power-supply: true + no-hpd: true + hpd-gpios: true + +additionalProperties: false + +required: + - compatible + - power-supply + +examples: + - | + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + bridge@2d { + compatible = "ti,sn65dsi86"; + reg = <0x2d>; + + interrupt-parent = <&tlmm>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>; + + vpll-supply = <&src_pp1800_s4a>; + vccio-supply = <&src_pp1800_s4a>; + vcca-supply = <&src_pp1200_l2a>; + vcc-supply = <&src_pp1200_l2a>; + + clocks = <&rpmhcc RPMH_LN_BB_CLK2>; + clock-names = "refclk"; + + no-hpd; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + sn65dsi86_out: endpoint { + remote-endpoint = <&panel_in_edp>; + }; + }; + }; + + aux-bus { + panel { + compatible = "edp-panel"; + power-supply = <&pp3300_dx_edp>; + backlight = <&backlight>; + hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; + hpd-reliable-delay-ms = <15>; + + port { + panel_in_edp: endpoint { + remote-endpoint = <&sn65dsi86_out>; + }; + }; + }; + }; + }; + }; |