diff options
Diffstat (limited to 'dts/Bindings/display/panel/tpo,tpg110.txt')
| -rw-r--r-- | dts/Bindings/display/panel/tpo,tpg110.txt | 81 |
1 files changed, 52 insertions, 29 deletions
diff --git a/dts/Bindings/display/panel/tpo,tpg110.txt b/dts/Bindings/display/panel/tpo,tpg110.txt index f5e3c6f209..40f3d7c713 100644 --- a/dts/Bindings/display/panel/tpo,tpg110.txt +++ b/dts/Bindings/display/panel/tpo,tpg110.txt @@ -1,47 +1,70 @@ TPO TPG110 Panel ================ -This binding builds on the DPI bindings, adding a few properties -as a superset of a DPI. See panel-dpi.txt for the required DPI -bindings. +This panel driver is a component that acts as an intermediary +between an RGB output and a variety of panels. The panel +driver is strapped up in electronics to the desired resolution +and other properties, and has a control interface over 3WIRE +SPI. By talking to the TPG110 over SPI, the strapped properties +can be discovered and the hardware is therefore mostly +self-describing. + + +--------+ +SPI -> | TPO | -> physical display +RGB -> | TPG110 | + +--------+ + +If some electrical strap or alternate resolution is desired, +this can be set up by taking software control of the display +over the SPI interface. The interface can also adjust +for properties of the display such as gamma correction and +certain electrical driving levels. + +The TPG110 does not know the physical dimensions of the panel +connected, so this needs to be specified in the device tree. + +It requires a GPIO line for control of its reset line. + +The serial protocol has line names that resemble I2C but the +protocol is not I2C but 3WIRE SPI. Required properties: -- compatible : "tpo,tpg110" +- compatible : one of: + "ste,nomadik-nhk15-display", "tpo,tpg110" + "tpo,tpg110" - grestb-gpios : panel reset GPIO -- scen-gpios : serial control enable GPIO -- scl-gpios : serial control clock line GPIO -- sda-gpios : serial control data line GPIO +- width-mm : see display/panel/panel-common.txt +- height-mm : see display/panel/panel-common.txt + +The device needs to be a child of an SPI bus, see +spi/spi-bus.txt. The SPI child must set the following +properties: +- spi-3wire +- spi-max-frequency = <3000000>; +as these are characteristics of this device. -Required nodes: -- Video port for DPI input, see panel-dpi.txt -- Panel timing for DPI setup, see panel-dpi.txt +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in +media/video-interfaces.txt. This node should describe panel's video bus. Example ------- -panel { - compatible = "tpo,tpg110", "panel-dpi"; - grestb-gpios = <&stmpe_gpio44 5 GPIO_ACTIVE_LOW>; - scen-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; - scl-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; - sda-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; +panel: display@0 { + compatible = "tpo,tpg110"; + reg = <0>; + spi-3wire; + /* 320 ns min period ~= 3 MHz */ + spi-max-frequency = <3000000>; + /* Width and height from data sheet */ + width-mm = <116>; + height-mm = <87>; + grestb-gpios = <&foo_gpio 5 GPIO_ACTIVE_LOW>; backlight = <&bl>; port { nomadik_clcd_panel: endpoint { - remote-endpoint = <&nomadik_clcd_pads>; + remote-endpoint = <&foo>; }; }; - - panel-timing { - clock-frequency = <33200000>; - hactive = <800>; - hback-porch = <216>; - hfront-porch = <40>; - hsync-len = <1>; - vactive = <480>; - vback-porch = <35>; - vfront-porch = <10>; - vsync-len = <1>; - }; }; |