1 files changed, 0 insertions, 91 deletions
diff --git a/dts/Bindings/display/simple-framebuffer.txt b/dts/Bindings/display/simple-framebuffer.txt
deleted file mode 100644
index 5a9ce511be..0000000000
--- a/dts/Bindings/display/simple-framebuffer.txt
+++ /dev/null
@@ -1,91 +0,0 @@
-Simple Framebuffer
-
-A simple frame-buffer describes a frame-buffer setup by firmware or
-the bootloader, with the assumption that the display hardware has already
-been set up to scan out from the memory pointed to by the reg property.
-
-Since simplefb nodes represent runtime information they must be sub-nodes of
-the chosen node (*). Simplefb nodes must be named "framebuffer@<address>".
-
-If the devicetree contains nodes for the display hardware used by a simplefb,
-then the simplefb node must contain a property called "display", which
-contains a phandle pointing to the primary display hw node, so that the OS
-knows which simplefb to disable when handing over control to a driver for the
-real hardware. The bindings for the hw nodes must specify which node is
-considered the primary node.
-
-It is advised to add display# aliases to help the OS determine how to number
-things. If display# aliases are used, then if the simplefb node contains a
-"display" property then the /aliases/display# path must point to the display
-hw node the "display" property points to, otherwise it must point directly
-to the simplefb node.
-
-If a simplefb node represents the preferred console for user interaction,
-then the chosen node's stdout-path property should point to it, or to the
-primary display hw node, as with display# aliases. If display aliases are
-used then it should be set to the alias instead.
-
-It is advised that devicetree files contain pre-filled, disabled framebuffer
-nodes, so that the firmware only needs to update the mode information and
-enable them. This way if e.g. later on support for more display clocks get
-added, the simplefb nodes will already contain this info and the firmware
-does not need to be updated.
-
-If pre-filled framebuffer nodes are used, the firmware may need extra
-information to find the right node. In that case an extra platform specific
-compatible and platform specific properties should be used and documented,
-see e.g. simple-framebuffer-sunxi.txt .
-
-Required properties:
-- compatible: "simple-framebuffer"
-- reg: Should contain the location and size of the framebuffer memory.
-- width: The width of the framebuffer in pixels.
-- height: The height of the framebuffer in pixels.
-- stride: The number of bytes in each line of the framebuffer.
-- format: The format of the framebuffer surface. Valid values are:
-  - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b).
-  - a8b8g8r8 (32-bit pixels, d[31:24]=a, d[23:16]=b, d[15:8]=g, d[7:0]=r).
-
-Optional properties:
-- clocks : List of clocks used by the framebuffer.
-- *-supply : Any number of regulators used by the framebuffer. These should
-	     be named according to the names in the device's design.
-
-  The above resources are expected to already be configured correctly.
-  The OS must ensure they are not modified or disabled while the simple
-  framebuffer remains active.
-
-- display : phandle pointing to the primary display hardware node
-
-Example:
-
-aliases {
-	display0 = &lcdc0;
-}
-
-chosen {
-	framebuffer0: framebuffer@1d385000 {
-		compatible = "simple-framebuffer";
-		reg = <0x1d385000 (1600 * 1200 * 2)>;
-		width = <1600>;
-		height = <1200>;
-		stride = <(1600 * 2)>;
-		format = "r5g6b5";
-		clocks = <&ahb_gates 36>, <&ahb_gates 43>, <&ahb_gates 44>;
-		lcd-supply = <&reg_dc1sw>;
-		display = <&lcdc0>;
-	};
-	stdout-path = "display0";
-};
-
-soc@1c00000 {
-	lcdc0: lcdc@1c0c000 {
-		compatible = "allwinner,sun4i-a10-lcdc";
-		...
-	};
-};
-
-
-*) Older devicetree files may have a compatible = "simple-framebuffer" node
-in a different place, operating systems must first enumerate any compatible
-nodes found under chosen and then check for other compatible nodes.