1 files changed, 0 insertions, 104 deletions
diff --git a/dts/Bindings/display/ste,mcde.txt b/dts/Bindings/display/ste,mcde.txt
deleted file mode 100644
index 4c33c692bd..0000000000
--- a/dts/Bindings/display/ste,mcde.txt
+++ /dev/null
@@ -1,104 +0,0 @@
-ST-Ericsson Multi Channel Display Engine MCDE
-
-The ST-Ericsson MCDE is a display controller with support for compositing
-and displaying several channels memory resident graphics data on DSI or
-LCD displays or bridges. It is used in the ST-Ericsson U8500 platform.
-
-Required properties:
-
-- compatible: must be:
-  "ste,mcde"
-- reg: register base for the main MCDE control registers, should be
-  0x1000 in size
-- interrupts: the interrupt line for the MCDE
-- epod-supply: a phandle to the EPOD regulator
-- vana-supply: a phandle to the analog voltage regulator
-- clocks: an array of the MCDE clocks in this strict order:
-  MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI
-  (HDMI clock), DSI0ESCLK (DSI0 energy save clock),
-  DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy
-  save clock)
-- clock-names: must be the following array:
-  "mcde", "lcd", "hdmi"
-  to match the required clock inputs above.
-- #address-cells: should be <1> (for the DSI hosts that will be children)
-- #size-cells: should be <1> (for the DSI hosts that will be children)
-- ranges: this should always be stated
-
-Required subnodes:
-
-The devicetree must specify subnodes for the DSI host adapters.
-These must have the following characteristics:
-
-- compatible: must be:
-  "ste,mcde-dsi"
-- reg: must specify the register range for the DSI host
-- vana-supply: phandle to the VANA voltage regulator
-- clocks: phandles to the high speed and low power (energy save) clocks
-  the high speed clock is not present on the third (dsi2) block, so it
-  should only have the "lp" clock
-- clock-names: "hs" for the high speed clock and "lp" for the low power
-  (energy save) clock
-- #address-cells: should be <1>
-- #size-cells: should be <0>
-
-Display panels and bridges will appear as children on the DSI hosts, and
-the displays are connected to the DSI hosts using the common binding
-for video transmitter interfaces; see
-Documentation/devicetree/bindings/media/video-interfaces.txt
-
-If a DSI host is unused (not connected) it will have no children defined.
-
-Example:
-
-mcde@a0350000 {
-	compatible = "ste,mcde";
-	reg = <0xa0350000 0x1000>;
-	interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
-	epod-supply = <&db8500_b2r2_mcde_reg>;
-	vana-supply = <&ab8500_ldo_ana_reg>;
-	clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
-		 <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
-		 <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */
-	clock-names = "mcde", "lcd", "hdmi";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	ranges;
-
-	dsi0: dsi@a0351000 {
-		compatible = "ste,mcde-dsi";
-		reg = <0xa0351000 0x1000>;
-		vana-supply = <&ab8500_ldo_ana_reg>;
-		clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>;
-		clock-names = "hs", "lp";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		panel {
-			compatible = "samsung,s6d16d0";
-			reg = <0>;
-			vdd1-supply = <&ab8500_ldo_aux1_reg>;
-			reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
-		};
-
-	};
-	dsi1: dsi@a0352000 {
-		compatible = "ste,mcde-dsi";
-		reg = <0xa0352000 0x1000>;
-		vana-supply = <&ab8500_ldo_ana_reg>;
-		clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>;
-		clock-names = "hs", "lp";
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
-	dsi2: dsi@a0353000 {
-		compatible = "ste,mcde-dsi";
-		reg = <0xa0353000 0x1000>;
-		vana-supply = <&ab8500_ldo_ana_reg>;
-		/* This DSI port only has the Low Power / Energy Save clock */
-		clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>;
-		clock-names = "lp";
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
-};