diff options
Diffstat (limited to 'dts/Bindings/display/sunxi/sun4i-drm.txt')
| -rw-r--r-- | dts/Bindings/display/sunxi/sun4i-drm.txt | 127 |
1 files changed, 121 insertions, 6 deletions
diff --git a/dts/Bindings/display/sunxi/sun4i-drm.txt b/dts/Bindings/display/sunxi/sun4i-drm.txt index 57a8d06100..b83e601804 100644 --- a/dts/Bindings/display/sunxi/sun4i-drm.txt +++ b/dts/Bindings/display/sunxi/sun4i-drm.txt @@ -4,6 +4,44 @@ Allwinner A10 Display Pipeline The Allwinner A10 Display pipeline is composed of several components that are going to be documented below: +For the input port of all components up to the TCON in the display +pipeline, if there are multiple components, the local endpoint IDs +must correspond to the index of the upstream block. For example, if +the remote endpoint is Frontend 1, then the local endpoint ID must +be 1. + +Conversely, for the output ports of the same group, the remote endpoint +ID must be the index of the local hardware block. If the local backend +is backend 1, then the remote endpoint ID must be 1. + +HDMI Encoder +------------ + +The HDMI Encoder supports the HDMI video and audio outputs, and does +CEC. It is one end of the pipeline. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a10s-hdmi + - reg: base address and size of memory-mapped region + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the HDMI encoder + * ahb: the HDMI interface clock + * mod: the HDMI module clock + * pll-0: the first video PLL + * pll-1: the second video PLL + - clock-names: the clock names mentioned above + - dmas: phandles to the DMA channels used by the HDMI encoder + * ddc-tx: The channel for DDC transmission + * ddc-rx: The channel for DDC reception + * audio-tx: The channel used for audio transmission + - dma-names: the channel names mentioned above + + - ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint. The second should be the + output, usually to an HDMI connector. + TV Encoder ---------- @@ -31,6 +69,7 @@ Required properties: * allwinner,sun6i-a31-tcon * allwinner,sun6i-a31s-tcon * allwinner,sun8i-a33-tcon + * allwinner,sun8i-v3s-tcon - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the TCON. Three are needed: @@ -47,12 +86,15 @@ Required properties: Documentation/devicetree/bindings/media/video-interfaces.txt. The first port should be the input endpoint, the second one the output - The output should have two endpoints. The first is the block - connected to the TCON channel 0 (usually a panel or a bridge), the - second the block connected to the TCON channel 1 (usually the TV - encoder) + The output may have multiple endpoints. The TCON has two channels, + usually with the first channel being used for the panels interfaces + (RGB, LVDS, etc.), and the second being used for the outputs that + require another controller (TV Encoder, HDMI, etc.). The endpoints + will take an extra property, allwinner,tcon-channel, to specify the + channel the endpoint is associated to. If that property is not + present, the endpoint number will be used as the channel number. -On SoCs other than the A33, there is one more clock required: +On SoCs other than the A33 and V3s, there is one more clock required: - 'tcon-ch1': The clock driving the TCON channel 1 DRC @@ -138,6 +180,26 @@ Required properties: Documentation/devicetree/bindings/media/video-interfaces.txt. The first port should be the input endpoints, the second one the outputs +Display Engine 2.0 Mixer +------------------------ + +The DE2 mixer have many functionalities, currently only layer blending is +supported. + +Required properties: + - compatible: value must be one of: + * allwinner,sun8i-v3s-de2-mixer + - reg: base address and size of the memory-mapped region. + - clocks: phandles to the clocks feeding the mixer + * bus: the mixer interface clock + * mod: the mixer module clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset controllers driving the mixer + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the output + Display Engine Pipeline ----------------------- @@ -148,13 +210,15 @@ extra node. Required properties: - compatible: value must be one of: + * allwinner,sun5i-a10s-display-engine * allwinner,sun5i-a13-display-engine * allwinner,sun6i-a31-display-engine * allwinner,sun6i-a31s-display-engine * allwinner,sun8i-a33-display-engine + * allwinner,sun8i-v3s-display-engine - allwinner,pipelines: list of phandle to the display engine - frontends available. + frontends (DE 1.0) or mixers (DE 2.0) available. Example: @@ -173,6 +237,57 @@ panel: panel { }; }; +connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; +}; + +hdmi: hdmi@01c16000 { + compatible = "allwinner,sun5i-a10s-hdmi"; + reg = <0x01c16000 0x1000>; + interrupts = <58>; + clocks = <&ccu CLK_AHB_HDMI>, <&ccu CLK_HDMI>, + <&ccu CLK_PLL_VIDEO0_2X>, + <&ccu CLK_PLL_VIDEO1_2X>; + clock-names = "ahb", "mod", "pll-0", "pll-1"; + dmas = <&dma SUN4I_DMA_NORMAL 16>, + <&dma SUN4I_DMA_NORMAL 16>, + <&dma SUN4I_DMA_DEDICATED 24>; + dma-names = "ddc-tx", "ddc-rx", "audio-tx"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + hdmi_in_tcon0: endpoint { + remote-endpoint = <&tcon0_out_hdmi>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; + }; + }; +}; + tve0: tv-encoder@01c0a000 { compatible = "allwinner,sun4i-a10-tv-encoder"; reg = <0x01c0a000 0x1000>; |