diff options
Diffstat (limited to 'dts/Bindings/display/tegra/nvidia,tegra20-host1x.txt')
| -rw-r--r-- | dts/Bindings/display/tegra/nvidia,tegra20-host1x.txt | 675 |
1 files changed, 0 insertions, 675 deletions
diff --git a/dts/Bindings/display/tegra/nvidia,tegra20-host1x.txt b/dts/Bindings/display/tegra/nvidia,tegra20-host1x.txt deleted file mode 100644 index e61999ce54..0000000000 --- a/dts/Bindings/display/tegra/nvidia,tegra20-host1x.txt +++ /dev/null @@ -1,675 +0,0 @@ -NVIDIA Tegra host1x - -Required properties: -- compatible: "nvidia,tegra<chip>-host1x" -- reg: Physical base address and length of the controller's registers. - For pre-Tegra186, one entry describing the whole register area. - For Tegra186, one entry for each entry in reg-names: - "vm" - VM region assigned to Linux - "hypervisor" - Hypervisor region (only if Linux acts as hypervisor) -- interrupts: The interrupt outputs from the controller. -- #address-cells: The number of cells used to represent physical base addresses - in the host1x address space. Should be 1. -- #size-cells: The number of cells used to represent the size of an address - range in the host1x address space. Should be 1. -- ranges: The mapping of the host1x address space to the CPU address space. -- clocks: Must contain one entry, for the module clock. - See ../clocks/clock-bindings.txt for details. -- resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names: Must include the following entries: - - host1x - - mc - -Optional properties: -- operating-points-v2: See ../bindings/opp/opp.txt for details. - - power-domains: Phandle to HEG or core power domain. - -For each opp entry in 'operating-points-v2' table of host1x and its modules: -- opp-supported-hw: One bitfield indicating: - On Tegra20: SoC process ID mask - On Tegra30+: SoC speedo ID mask - - A bitwise AND is performed against the value and if any bit - matches, the OPP gets enabled. - -Each host1x client module having to perform DMA through the Memory Controller -should have the interconnect endpoints set to the Memory Client and External -Memory respectively. - -The host1x top-level node defines a number of children, each representing one -of the following host1x client modules: - -- mpe: video encoder - - Required properties: - - compatible: "nvidia,tegra<chip>-mpe" - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - clocks: Must contain one entry, for the module clock. - See ../clocks/clock-bindings.txt for details. - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - mpe - - Optional properties: - - interconnects: Must contain entry for the MPE memory clients. - - interconnect-names: Must include name of the interconnect path for each - interconnect entry. Consult TRM documentation for information about - available memory clients, see MEMORY CONTROLLER section. - - operating-points-v2: See ../bindings/opp/opp.txt for details. - - power-domains: Phandle to MPE power domain. - -- vi: video input - - Required properties: - - compatible: "nvidia,tegra<chip>-vi" - - reg: Physical base address and length of the controller registers. - - interrupts: The interrupt outputs from the controller. - - clocks: clocks: Must contain one entry, for the module clock. - See ../clocks/clock-bindings.txt for details. - - Tegra20/Tegra30/Tegra114/Tegra124: - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - vi - - Tegra210: - - power-domains: Must include venc powergate node as vi is in VE partition. - - ports (optional node) - vi can have optional ports node and max 6 ports are supported. Each port - should have single 'endpoint' child node. All port nodes are grouped under - ports node. Please refer to the bindings defined in - Documentation/devicetree/bindings/media/video-interfaces.txt - - csi (required node) - Tegra210 has CSI part of VI sharing same host interface and register space. - So, VI device node should have CSI child node. - - - csi: mipi csi interface to vi - - Required properties: - - compatible: "nvidia,tegra210-csi" - - reg: Physical base address offset to parent and length of the controller - registers. - - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks. - See ../clocks/clock-bindings.txt for details. - - power-domains: Must include sor powergate node as csicil is in - SOR partition. - - channel (optional nodes) - Maximum 6 channels are supported with each csi brick as either x4 or x2 - based on hw connectivity to sensor. - - Required properties: - - reg: csi port number. Valid port numbers are 0 through 5. - - nvidia,mipi-calibrate: Should contain a phandle and a specifier - specifying which pads are used by this CSI port and need to be - calibrated. See also ../display/tegra/nvidia,tegra114-mipi.txt. - - Each channel node must contain 2 port nodes which can be grouped - under 'ports' node and each port should have a single child 'endpoint' - node. - - ports node - Please refer to the bindings defined in - Documentation/devicetree/bindings/media/video-interfaces.txt - - ports node must contain below 2 port nodes. - port@0 with single child 'endpoint' node always a sink. - port@1 with single child 'endpoint' node always a source. - - port@0 (required node) - Required properties: - - reg: 0 - - endpoint (required node) - Required properties: - - data-lanes: an array of data lane from 1 to 8. Valid array - lengths are 1/2/4/8. - - remote-endpoint: phandle to sensor 'endpoint' node. - - port@1 (required node) - Required properties: - - reg: 1 - - endpoint (required node) - Required properties: - - remote-endpoint: phandle to vi port 'endpoint' node. - - Optional properties: - - interconnects: Must contain entry for the VI memory clients. - - interconnect-names: Must include name of the interconnect path for each - interconnect entry. Consult TRM documentation for information about - available memory clients, see MEMORY CONTROLLER section. - - operating-points-v2: See ../bindings/opp/opp.txt for details. - - power-domains: Phandle to VENC power domain. - -- epp: encoder pre-processor - - Required properties: - - compatible: "nvidia,tegra<chip>-epp" - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - clocks: Must contain one entry, for the module clock. - See ../clocks/clock-bindings.txt for details. - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - epp - - Optional properties: - - interconnects: Must contain entry for the EPP memory clients. - - interconnect-names: Must include name of the interconnect path for each - interconnect entry. Consult TRM documentation for information about - available memory clients, see MEMORY CONTROLLER section. - - operating-points-v2: See ../bindings/opp/opp.txt for details. - - power-domains: Phandle to HEG or core power domain. - -- isp: image signal processor - - Required properties: - - compatible: "nvidia,tegra<chip>-isp" - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - clocks: Must contain one entry, for the module clock. - See ../clocks/clock-bindings.txt for details. - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - isp - - Optional properties: - - interconnects: Must contain entry for the ISP memory clients. - - interconnect-names: Must include name of the interconnect path for each - interconnect entry. Consult TRM documentation for information about - available memory clients, see MEMORY CONTROLLER section. - - power-domains: Phandle to VENC or core power domain. - -- gr2d: 2D graphics engine - - Required properties: - - compatible: "nvidia,tegra<chip>-gr2d" - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - clocks: Must contain one entry, for the module clock. - See ../clocks/clock-bindings.txt for details. - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - 2d - - mc - - Optional properties: - - interconnects: Must contain entry for the GR2D memory clients. - - interconnect-names: Must include name of the interconnect path for each - interconnect entry. Consult TRM documentation for information about - available memory clients, see MEMORY CONTROLLER section. - - operating-points-v2: See ../bindings/opp/opp.txt for details. - - power-domains: Phandle to HEG or core power domain. - -- gr3d: 3D graphics engine - - Required properties: - - compatible: "nvidia,tegra<chip>-gr3d" - - reg: Physical base address and length of the controller's registers. - - clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. - - clock-names: Must include the following entries: - (This property may be omitted if the only clock in the list is "3d") - - 3d - This MUST be the first entry. - - 3d2 (Only required on SoCs with two 3D clocks) - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - 3d - - 3d2 (Only required on SoCs with two 3D clocks) - - mc - - mc2 (Only required on SoCs with two 3D clocks) - - Optional properties: - - interconnects: Must contain entry for the GR3D memory clients. - - interconnect-names: Must include name of the interconnect path for each - interconnect entry. Consult TRM documentation for information about - available memory clients, see MEMORY CONTROLLER section. - - operating-points-v2: See ../bindings/opp/opp.txt for details. - - power-domains: Phandles to 3D or core power domain. - -- dc: display controller - - Required properties: - - compatible: "nvidia,tegra<chip>-dc" - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. - - clock-names: Must include the following entries: - - dc - This MUST be the first entry. - - parent - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - dc - - nvidia,head: The number of the display controller head. This is used to - setup the various types of output to receive video data from the given - head. - - Each display controller node has a child node, named "rgb", that represents - the RGB output associated with the controller. It can take the following - optional properties: - - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection - - nvidia,edid: supplies a binary EDID blob - - nvidia,panel: phandle of a display panel - - interconnects: Must contain entry for the DC memory clients. - - interconnect-names: Must include name of the interconnect path for each - interconnect entry. Consult TRM documentation for information about - available memory clients, see MEMORY CONTROLLER section. - - operating-points-v2: See ../bindings/opp/opp.txt for details. - - power-domains: Phandle to core power domain. - -- hdmi: High Definition Multimedia Interface - - Required properties: - - compatible: "nvidia,tegra<chip>-hdmi" - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - hdmi-supply: supply for the +5V HDMI connector pin - - vdd-supply: regulator for supply voltage - - pll-supply: regulator for PLL - - clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. - - clock-names: Must include the following entries: - - hdmi - This MUST be the first entry. - - parent - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - hdmi - - Optional properties: - - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection - - nvidia,edid: supplies a binary EDID blob - - nvidia,panel: phandle of a display panel - - operating-points-v2: See ../bindings/opp/opp.txt for details. - -- tvo: TV encoder output - - Required properties: - - compatible: "nvidia,tegra<chip>-tvo" - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - clocks: Must contain one entry, for the module clock. - See ../clocks/clock-bindings.txt for details. - - Optional properties: - - operating-points-v2: See ../bindings/opp/opp.txt for details. - - power-domains: Phandle to core power domain. - -- dsi: display serial interface - - Required properties: - - compatible: "nvidia,tegra<chip>-dsi" - - reg: Physical base address and length of the controller's registers. - - clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. - - clock-names: Must include the following entries: - - dsi - This MUST be the first entry. - - lp - - parent - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - dsi - - avdd-dsi-supply: phandle of a supply that powers the DSI controller - - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying - which pads are used by this DSI output and need to be calibrated. See also - ../display/tegra/nvidia,tegra114-mipi.txt. - - Optional properties: - - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection - - nvidia,edid: supplies a binary EDID blob - - nvidia,panel: phandle of a display panel - - nvidia,ganged-mode: contains a phandle to a second DSI controller to gang - up with in order to support up to 8 data lanes - - operating-points-v2: See ../bindings/opp/opp.txt for details. - -- sor: serial output resource - - Required properties: - - compatible: Should be: - - "nvidia,tegra124-sor": for Tegra124 and Tegra132 - - "nvidia,tegra132-sor": for Tegra132 - - "nvidia,tegra210-sor": for Tegra210 - - "nvidia,tegra210-sor1": for Tegra210 - - "nvidia,tegra186-sor": for Tegra186 - - "nvidia,tegra186-sor1": for Tegra186 - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. - - clock-names: Must include the following entries: - - sor: clock input for the SOR hardware - - out: SOR output clock - - parent: input for the pixel clock - - dp: reference clock for the SOR clock - - safe: safe reference for the SOR clock during power up - - For Tegra186 and later: - - pad: SOR pad output clock (on Tegra186 and later) - - Obsolete: - - source: source clock for the SOR clock (obsolete, use "out" instead) - - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - sor - - Required properties on Tegra186 and later: - - nvidia,interface: index of the SOR interface - - Optional properties: - - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection - - nvidia,edid: supplies a binary EDID blob - - nvidia,panel: phandle of a display panel - - nvidia,xbar-cfg: 5 cells containing the crossbar configuration. Each lane - of the SOR, identified by the cell's index, is mapped via the crossbar to - the pad specified by the cell's value. - - Optional properties when driving an eDP output: - - nvidia,dpaux: phandle to a DispayPort AUX interface - -- dpaux: DisplayPort AUX interface - - compatible : Should contain one of the following: - - "nvidia,tegra124-dpaux": for Tegra124 and Tegra132 - - "nvidia,tegra210-dpaux": for Tegra210 - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. - - clock-names: Must include the following entries: - - dpaux: clock input for the DPAUX hardware - - parent: reference clock - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - dpaux - - vdd-supply: phandle of a supply that powers the DisplayPort link - - i2c-bus: Subnode where I2C slave devices are listed. This subnode - must be always present. If there are no I2C slave devices, an empty - node should be added. See ../../i2c/i2c.txt for more information. - - See ../pinctrl/nvidia,tegra124-dpaux-padctl.txt for information - regarding the DPAUX pad controller bindings. - -- vic: Video Image Compositor - - compatible : "nvidia,tegra<chip>-vic" - - reg: Physical base address and length of the controller's registers. - - interrupts: The interrupt outputs from the controller. - - clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. - - clock-names: Must include the following entries: - - vic: clock input for the VIC hardware - - resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. - - reset-names: Must include the following entries: - - vic - - Optional properties: - - interconnects: Must contain entry for the VIC memory clients. - - interconnect-names: Must include name of the interconnect path for each - interconnect entry. Consult TRM documentation for information about - available memory clients, see MEMORY CONTROLLER section. - -Example: - -/ { - ... - - host1x { - compatible = "nvidia,tegra20-host1x", "simple-bus"; - reg = <0x50000000 0x00024000>; - interrupts = <0 65 0x04 /* mpcore syncpt */ - 0 67 0x04>; /* mpcore general */ - clocks = <&tegra_car TEGRA20_CLK_HOST1X>; - resets = <&tegra_car 28>; - reset-names = "host1x"; - operating-points-v2 = <&dvfs_opp_table>; - power-domains = <&domain>; - - #address-cells = <1>; - #size-cells = <1>; - - ranges = <0x54000000 0x54000000 0x04000000>; - - mpe { - compatible = "nvidia,tegra20-mpe"; - reg = <0x54040000 0x00040000>; - interrupts = <0 68 0x04>; - clocks = <&tegra_car TEGRA20_CLK_MPE>; - resets = <&tegra_car 60>; - reset-names = "mpe"; - operating-points-v2 = <&dvfs_opp_table>; - power-domains = <&domain>; - }; - - vi@54080000 { - compatible = "nvidia,tegra210-vi"; - reg = <0x0 0x54080000 0x0 0x700>; - interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; - assigned-clocks = <&tegra_car TEGRA210_CLK_VI>; - assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>; - operating-points-v2 = <&dvfs_opp_table>; - - clocks = <&tegra_car TEGRA210_CLK_VI>; - power-domains = <&pd_venc>; - - #address-cells = <1>; - #size-cells = <1>; - - ranges = <0x0 0x0 0x54080000 0x2000>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - imx219_vi_in0: endpoint { - remote-endpoint = <&imx219_csi_out0>; - }; - }; - }; - - csi@838 { - compatible = "nvidia,tegra210-csi"; - reg = <0x838 0x1300>; - assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>, - <&tegra_car TEGRA210_CLK_CILCD>, - <&tegra_car TEGRA210_CLK_CILE>, - <&tegra_car TEGRA210_CLK_CSI_TPG>; - assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>, - <&tegra_car TEGRA210_CLK_PLL_P>, - <&tegra_car TEGRA210_CLK_PLL_P>; - assigned-clock-rates = <102000000>, - <102000000>, - <102000000>, - <972000000>; - - clocks = <&tegra_car TEGRA210_CLK_CSI>, - <&tegra_car TEGRA210_CLK_CILAB>, - <&tegra_car TEGRA210_CLK_CILCD>, - <&tegra_car TEGRA210_CLK_CILE>, - <&tegra_car TEGRA210_CLK_CSI_TPG>; - clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg"; - power-domains = <&pd_sor>; - - #address-cells = <1>; - #size-cells = <0>; - - channel@0 { - reg = <0>; - nvidia,mipi-calibrate = <&mipi 0x001>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - imx219_csi_in0: endpoint { - data-lanes = <1 2>; - remote-endpoint = <&imx219_out0>; - }; - }; - - port@1 { - reg = <1>; - imx219_csi_out0: endpoint { - remote-endpoint = <&imx219_vi_in0>; - }; - }; - }; - }; - }; - }; - - epp { - compatible = "nvidia,tegra20-epp"; - reg = <0x540c0000 0x00040000>; - interrupts = <0 70 0x04>; - clocks = <&tegra_car TEGRA20_CLK_EPP>; - resets = <&tegra_car 19>; - reset-names = "epp"; - operating-points-v2 = <&dvfs_opp_table>; - power-domains = <&domain>; - }; - - isp { - compatible = "nvidia,tegra20-isp"; - reg = <0x54100000 0x00040000>; - interrupts = <0 71 0x04>; - clocks = <&tegra_car TEGRA20_CLK_ISP>; - resets = <&tegra_car 23>; - reset-names = "isp"; - }; - - gr2d { - compatible = "nvidia,tegra20-gr2d"; - reg = <0x54140000 0x00040000>; - interrupts = <0 72 0x04>; - clocks = <&tegra_car TEGRA20_CLK_GR2D>; - resets = <&tegra_car 21>; - reset-names = "2d"; - operating-points-v2 = <&dvfs_opp_table>; - power-domains = <&domain>; - }; - - gr3d { - compatible = "nvidia,tegra20-gr3d"; - reg = <0x54180000 0x00040000>; - clocks = <&tegra_car TEGRA20_CLK_GR3D>; - resets = <&tegra_car 24>; - reset-names = "3d"; - operating-points-v2 = <&dvfs_opp_table>; - power-domains = <&domain>; - }; - - dc@54200000 { - compatible = "nvidia,tegra20-dc"; - reg = <0x54200000 0x00040000>; - interrupts = <0 73 0x04>; - clocks = <&tegra_car TEGRA20_CLK_DISP1>, - <&tegra_car TEGRA20_CLK_PLL_P>; - clock-names = "dc", "parent"; - resets = <&tegra_car 27>; - reset-names = "dc"; - operating-points-v2 = <&dvfs_opp_table>; - power-domains = <&domain>; - - interconnects = <&mc TEGRA20_MC_DISPLAY0A &emc>, - <&mc TEGRA20_MC_DISPLAY0B &emc>, - <&mc TEGRA20_MC_DISPLAY0C &emc>, - <&mc TEGRA20_MC_DISPLAYHC &emc>; - interconnect-names = "wina", - "winb", - "winc", - "cursor"; - - rgb { - status = "disabled"; - }; - }; - - dc@54240000 { - compatible = "nvidia,tegra20-dc"; - reg = <0x54240000 0x00040000>; - interrupts = <0 74 0x04>; - clocks = <&tegra_car TEGRA20_CLK_DISP2>, - <&tegra_car TEGRA20_CLK_PLL_P>; - clock-names = "dc", "parent"; - resets = <&tegra_car 26>; - reset-names = "dc"; - operating-points-v2 = <&dvfs_opp_table>; - power-domains = <&domain>; - - interconnects = <&mc TEGRA20_MC_DISPLAY0AB &emc>, - <&mc TEGRA20_MC_DISPLAY0BB &emc>, - <&mc TEGRA20_MC_DISPLAY0CB &emc>, - <&mc TEGRA20_MC_DISPLAYHCB &emc>; - interconnect-names = "wina", - "winb", - "winc", - "cursor"; - - rgb { - status = "disabled"; - }; - }; - - hdmi { - compatible = "nvidia,tegra20-hdmi"; - reg = <0x54280000 0x00040000>; - interrupts = <0 75 0x04>; - clocks = <&tegra_car TEGRA20_CLK_HDMI>, - <&tegra_car TEGRA20_CLK_PLL_D_OUT0>; - clock-names = "hdmi", "parent"; - resets = <&tegra_car 51>; - reset-names = "hdmi"; - status = "disabled"; - operating-points-v2 = <&dvfs_opp_table>; - }; - - tvo { - compatible = "nvidia,tegra20-tvo"; - reg = <0x542c0000 0x00040000>; - interrupts = <0 76 0x04>; - clocks = <&tegra_car TEGRA20_CLK_TVO>; - status = "disabled"; - operating-points-v2 = <&dvfs_opp_table>; - }; - - dsi { - compatible = "nvidia,tegra20-dsi"; - reg = <0x54300000 0x00040000>; - clocks = <&tegra_car TEGRA20_CLK_DSI>, - <&tegra_car TEGRA20_CLK_PLL_D_OUT0>; - clock-names = "dsi", "parent"; - resets = <&tegra_car 48>; - reset-names = "dsi"; - status = "disabled"; - operating-points-v2 = <&dvfs_opp_table>; - }; - }; - - ... -}; |