1 files changed, 0 insertions, 81 deletions
diff --git a/dts/Bindings/dma/sun6i-dma.txt b/dts/Bindings/dma/sun6i-dma.txt
deleted file mode 100644
index cae31f4e77..0000000000
--- a/dts/Bindings/dma/sun6i-dma.txt
+++ /dev/null
@@ -1,81 +0,0 @@
-Allwinner A31 DMA Controller
-
-This driver follows the generic DMA bindings defined in dma.txt.
-
-Required properties:
-
-- compatible:	Must be one of
-		  "allwinner,sun6i-a31-dma"
-		  "allwinner,sun8i-a23-dma"
-		  "allwinner,sun8i-a83t-dma"
-		  "allwinner,sun8i-h3-dma"
-		  "allwinner,sun8i-v3s-dma"
-- reg:		Should contain the registers base address and length
-- interrupts:	Should contain a reference to the interrupt used by this device
-- clocks:	Should contain a reference to the parent AHB clock
-- resets:	Should contain a reference to the reset controller asserting
-		this device in reset
-- #dma-cells :	Should be 1, a single cell holding a line request number
-
-Example:
-	dma: dma-controller@1c02000 {
-		compatible = "allwinner,sun6i-a31-dma";
-		reg = <0x01c02000 0x1000>;
-		interrupts = <0 50 4>;
-		clocks = <&ahb1_gates 6>;
-		resets = <&ahb1_rst 6>;
-		#dma-cells = <1>;
-	};
-
-------------------------------------------------------------------------------
-For A64 and H6 DMA controller:
-
-Required properties:
-- compatible:	Must be one of
-		  "allwinner,sun50i-a64-dma"
-		  "allwinner,sun50i-h6-dma"
-- dma-channels: Number of DMA channels supported by the controller.
-		Refer to Documentation/devicetree/bindings/dma/dma.txt
-- clocks:	In addition to parent AHB clock, it should also contain mbus
-		clock (H6 only)
-- clock-names:	Should contain "bus" and "mbus" (H6 only)
-- all properties above, i.e. reg, interrupts, clocks, resets and #dma-cells
-
-Optional properties:
-- dma-requests: Number of DMA request signals supported by the controller.
-		Refer to Documentation/devicetree/bindings/dma/dma.txt
-
-Example:
-	dma: dma-controller@1c02000 {
-		compatible = "allwinner,sun50i-a64-dma";
-		reg = <0x01c02000 0x1000>;
-		interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&ccu CLK_BUS_DMA>;
-		dma-channels = <8>;
-		dma-requests = <27>;
-		resets = <&ccu RST_BUS_DMA>;
-		#dma-cells = <1>;
-	};
-------------------------------------------------------------------------------
-
-Clients:
-
-DMA clients connected to the A31 DMA controller must use the format
-described in the dma.txt file, using a two-cell specifier for each
-channel: a phandle plus one integer cells.
-The two cells in order are:
-
-1. A phandle pointing to the DMA controller.
-2. The port ID as specified in the datasheet
-
-Example:
-spi2: spi@1c6a000 {
-	compatible = "allwinner,sun6i-a31-spi";
-	reg = <0x01c6a000 0x1000>;
-	interrupts = <0 67 4>;
-	clocks = <&ahb1_gates 22>, <&spi2_clk>;
-	clock-names = "ahb", "mod";
-	dmas = <&dma 25>, <&dma 25>;
-	dma-names = "rx", "tx";
-	resets = <&ahb1_rst 22>;
-};