diff options
Diffstat (limited to 'dts/Bindings/drm/imx/ldb.txt')
| -rw-r--r-- | dts/Bindings/drm/imx/ldb.txt | 122 |
1 files changed, 122 insertions, 0 deletions
diff --git a/dts/Bindings/drm/imx/ldb.txt b/dts/Bindings/drm/imx/ldb.txt new file mode 100644 index 0000000000..443bcb6134 --- /dev/null +++ b/dts/Bindings/drm/imx/ldb.txt @@ -0,0 +1,122 @@ +Device-Tree bindings for LVDS Display Bridge (ldb) + +LVDS Display Bridge +=================== + +The LVDS Display Bridge device tree node contains up to two lvds-channel +nodes describing each of the two LVDS encoder channels of the bridge. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". + Both LDB versions are similar, but i.MX6 has an additional + multiplexer in the front to select any of the four IPU display + interfaces as input for each LVDS channel. + - gpr : should be <&gpr> on i.MX53 and i.MX6q. + The phandle points to the iomuxc-gpr region containing the LVDS + control register. +- clocks, clock-names : phandles to the LDB divider and selector clocks and to + the display interface selector clocks, as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt + The following clocks are expected on i.MX53: + "di0_pll" - LDB LVDS channel 0 mux + "di1_pll" - LDB LVDS channel 1 mux + "di0" - LDB LVDS channel 0 gate + "di1" - LDB LVDS channel 1 gate + "di0_sel" - IPU1 DI0 mux + "di1_sel" - IPU1 DI1 mux + On i.MX6q the following additional clocks are needed: + "di2_sel" - IPU2 DI0 mux + "di3_sel" - IPU2 DI1 mux + The needed clock numbers for each are documented in + Documentation/devicetree/bindings/clock/imx5-clock.txt, and in + Documentation/devicetree/bindings/clock/imx6q-clock.txt. + +Optional properties: + - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q + - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, + not used on i.MX6q + - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should + be configured - one input will be distributed on both outputs in dual + channel mode + +LVDS Channel +============ + +Each LVDS Channel has to contain a display-timings node that describes the +video timings for the connected LVDS display. For detailed information, also +have a look at Documentation/devicetree/bindings/video/display-timing.txt. + +Required properties: + - reg : should be <0> or <1> + - fsl,data-mapping : should be "spwg" or "jeida" + This describes how the color bits are laid out in the + serialized LVDS signal. + - fsl,data-width : should be <18> or <24> + - port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + On i.MX5, the internal two-input-multiplexer is used. + Due to hardware limitations, only one port (port@[0,1]) + can be used for each channel (lvds-channel@[0,1], respectively) + On i.MX6, there should be four ports (port@[0-3]) that correspond + to the four LVDS multiplexer inputs. + +example: + +gpr: iomuxc-gpr@53fa8000 { + /* ... */ +}; + +ldb: ldb@53fa8008 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ldb"; + gpr = <&gpr>; + clocks = <&clks 122>, <&clks 120>, + <&clks 115>, <&clks 116>, + <&clks 123>, <&clks 85>; + clock-names = "di0_pll", "di1_pll", + "di0_sel", "di1_sel", + "di0", "di1"; + + lvds-channel@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + + port@0 { + reg = <0>; + + lvds0_in: endpoint { + remote-endpoint = <&ipu_di0_lvds0>; + }; + }; + }; + + lvds-channel@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + + port@1 { + reg = <1>; + + lvds1_in: endpoint { + remote-endpoint = <&ipu_di1_lvds1>; + }; + }; + }; +}; |