summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/extcon/extcon-arizona.txt
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/extcon/extcon-arizona.txt')
-rw-r--r--dts/Bindings/extcon/extcon-arizona.txt60
1 files changed, 60 insertions, 0 deletions
diff --git a/dts/Bindings/extcon/extcon-arizona.txt b/dts/Bindings/extcon/extcon-arizona.txt
index e1705fae63..e27341f8a4 100644
--- a/dts/Bindings/extcon/extcon-arizona.txt
+++ b/dts/Bindings/extcon/extcon-arizona.txt
@@ -13,3 +13,63 @@ Optional properties:
ARIZONA_ACCDET_MODE_HPR or 2 - Headphone detect mode is set to HPDETR
If this node is not mentioned or if the value is unknown, then
headphone detection mode is set to HPDETL.
+
+ - wlf,use-jd2 : Use the additional JD input along with JD1 for dual pin jack
+ detection.
+ - wlf,use-jd2-nopull : Internal pull on JD2 is disabled when used for
+ jack detection.
+ - wlf,jd-invert : Invert the polarity of the jack detection switch
+
+ - wlf,micd-software-compare : Use a software comparison to determine mic
+ presence
+ - wlf,micd-detect-debounce : Additional software microphone detection
+ debounce specified in milliseconds.
+ - wlf,micd-pol-gpio : GPIO specifier for the GPIO controlling the headset
+ polarity if one exists.
+ - wlf,micd-bias-start-time : Time allowed for MICBIAS to startup prior to
+ performing microphone detection, specified as per the ARIZONA_MICD_TIME_XXX
+ defines.
+ - wlf,micd-rate : Delay between successive microphone detection measurements,
+ specified as per the ARIZONA_MICD_TIME_XXX defines.
+ - wlf,micd-dbtime : Microphone detection hardware debounces specified as the
+ number of measurements to take, valid values being 2 and 4.
+ - wlf,micd-timeout-ms : Timeout for microphone detection, specified in
+ milliseconds.
+ - wlf,micd-force-micbias : Force MICBIAS continuously on during microphone
+ detection.
+ - wlf,micd-configs : Headset polarity configurations (generally used for
+ detection of CTIA / OMTP headsets), the field can be of variable length
+ but should always be a multiple of 3 cells long, each three cell group
+ represents one polarity configuration.
+ The first cell defines the accessory detection pin, zero will use MICDET1
+ and all other values will use MICDET2.
+ The second cell represents the MICBIAS to be used.
+ The third cell represents the value of the micd-pol-gpio pin.
+
+ - wlf,gpsw : Settings for the general purpose switch
+
+Example:
+
+codec: wm8280@0 {
+ compatible = "wlf,wm8280";
+ reg = <0>;
+ ...
+
+ wlf,use-jd2;
+ wlf,use-jd2-nopull;
+ wlf,jd-invert;
+
+ wlf,micd-software-compare;
+ wlf,micd-detect-debounce = <0>;
+ wlf,micd-pol-gpio = <&codec 2 0>;
+ wlf,micd-rate = <ARIZONA_MICD_TIME_8MS>;
+ wlf,micd-dbtime = <4>;
+ wlf,micd-timeout-ms = <100>;
+ wlf,micd-force-micbias;
+ wlf,micd-configs = <
+ 0 1 0 /* MICDET1 MICBIAS1 GPIO=low */
+ 1 2 1 /* MICDET2 MICBIAS2 GPIO=high */
+ >;
+
+ wlf,gpsw = <0>;
+};