5 files changed, 91 insertions, 3 deletions
diff --git a/dts/Bindings/gpio/gpio-bcm-kona.txt b/dts/Bindings/gpio/brcm,kona-gpio.txt
index 4a63bc96b6..4a63bc96b6 100644
--- a/dts/Bindings/gpio/gpio-bcm-kona.txt
+++ b/dts/Bindings/gpio/brcm,kona-gpio.txt
diff --git a/dts/Bindings/gpio/gpio-altera.txt b/dts/Bindings/gpio/gpio-altera.txt
new file mode 100644
index 0000000000..12f50149e1
--- /dev/null
+++ b/dts/Bindings/gpio/gpio-altera.txt
@@ -0,0 +1,43 @@
+Altera GPIO controller bindings
+
+Required properties:
+- compatible:
+  - "altr,pio-1.0"
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells : Should be 2
+  - The first cell is the gpio offset number.
+  - The second cell is reserved and is currently unused.
+- gpio-controller : Marks the device node as a GPIO controller.
+- interrupt-controller: Mark the device node as an interrupt controller
+- #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware.
+  - The first cell is the GPIO offset number within the GPIO controller.
+- interrupts: Specify the interrupt.
+- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO
+  hardware is synthesized. This field is required if the Altera GPIO controller
+  used has IRQ enabled as the interrupt type is not software controlled,
+  but hardware synthesized. Required if GPIO is used as an interrupt
+  controller. The value is defined in <dt-bindings/interrupt-controller/irq.h>
+  Only the following flags are supported:
+    IRQ_TYPE_EDGE_RISING
+    IRQ_TYPE_EDGE_FALLING
+    IRQ_TYPE_EDGE_BOTH
+    IRQ_TYPE_LEVEL_HIGH
+
+Optional properties:
+- altr,ngpio: Width of the GPIO bank. This defines how many pins the
+  GPIO device has. Ranges between 1-32. Optional and defaults to 32 if not
+  specified.
+
+Example:
+
+gpio_altr: gpio@0xff200000 {
+	compatible = "altr,pio-1.0";
+	reg = <0xff200000 0x10>;
+	interrupts = <0 45 4>;
+	altr,ngpio = <32>;
+	altr,interrupt-trigger = <IRQ_TYPE_EDGE_RISING>;
+	#gpio-cells = <2>;
+	gpio-controller;
+	#interrupt-cells = <1>;
+	interrupt-controller;
+};
diff --git a/dts/Bindings/gpio/gpio-fan.txt b/dts/Bindings/gpio/gpio-fan.txt
index 2dd457a346..439a7430fc 100644
--- a/dts/Bindings/gpio/gpio-fan.txt
+++ b/dts/Bindings/gpio/gpio-fan.txt
@@ -2,15 +2,20 @@ Bindings for fan connected to GPIO lines
 
 Required properties:
 - compatible : "gpio-fan"
+
+Optional properties:
 - gpios: Specifies the pins that map to bits in the control value,
   ordered MSB-->LSB.
 - gpio-fan,speed-map: A mapping of possible fan RPM speeds and the
   control value that should be set to achieve them. This array
   must have the RPM values in ascending order.
-
-Optional properties:
 - alarm-gpios: This pin going active indicates something is wrong with
   the fan, and a udev event will be fired.
+- cooling-cells: If used as a cooling device, must be <2>
+  Also see: Documentation/devicetree/bindings/thermal/thermal.txt
+  min and max states are derived from the speed-map of the fan.
+
+Note: At least one the "gpios" or "alarm-gpios" properties must be set.
 
 Examples:
 
@@ -23,3 +28,13 @@ Examples:
 				      6000 2>;
 		alarm-gpios = <&gpio1 15 1>;
 	};
+	gpio_fan_cool: gpio_fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio2 14 1
+			 &gpio2 13 1>;
+		gpio-fan,speed-map =	<0    0>,
+					<3000 1>,
+					<6000 2>;
+		alarm-gpios = <&gpio2 15 1>;
+		#cooling-cells = <2>; /* min followed by max */
+	};
diff --git a/dts/Bindings/gpio/gpio.txt b/dts/Bindings/gpio/gpio.txt
index f7a158d858..5788d5cf12 100644
--- a/dts/Bindings/gpio/gpio.txt
+++ b/dts/Bindings/gpio/gpio.txt
@@ -116,6 +116,29 @@ Every GPIO controller node must contain both an empty "gpio-controller"
 property, and a #gpio-cells integer property, which indicates the number of
 cells in a gpio-specifier.
 
+The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism
+providing automatic GPIO request and configuration as part of the
+gpio-controller's driver probe function.
+
+Each GPIO hog definition is represented as a child node of the GPIO controller.
+Required properties:
+- gpio-hog:   A property specifying that this child node represent a GPIO hog.
+- gpios:      Store the GPIO information (id, flags, ...). Shall contain the
+	      number of cells specified in its parent node (GPIO controller
+	      node).
+Only one of the following properties scanned in the order shown below.
+This means that when multiple properties are present they will be searched
+in the order presented below and the first match is taken as the intended
+configuration.
+- input:      A property specifying to set the GPIO direction as input.
+- output-low  A property specifying to set the GPIO direction as output with
+	      the value low.
+- output-high A property specifying to set the GPIO direction as output with
+	      the value high.
+
+Optional properties:
+- line-name:  The GPIO label name. If not present the node name is used.
+
 Example of two SOC GPIO banks defined as gpio-controller nodes:
 
 	qe_pio_a: gpio-controller@1400 {
@@ -123,6 +146,13 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
 		reg = <0x1400 0x18>;
 		gpio-controller;
 		#gpio-cells = <2>;
+
+		line_b {
+			gpio-hog;
+			gpios = <6 0>;
+			output-low;
+			line-name = "foo-bar-gpio";
+		};
 	};
 
 	qe_pio_e: gpio-controller@1460 {
diff --git a/dts/Bindings/gpio/mrvl-gpio.txt b/dts/Bindings/gpio/mrvl-gpio.txt
index 67a2e4e414..98d1983969 100644
--- a/dts/Bindings/gpio/mrvl-gpio.txt
+++ b/dts/Bindings/gpio/mrvl-gpio.txt
@@ -12,7 +12,7 @@ Required properties:
   gpio_mux.
 - interrupt-names : Should be the names of irq resources. Each interrupt
   uses its own interrupt name, so there should be as many interrupt names
-  as referenced interrups.
+  as referenced interrupts.
 - interrupt-controller : Identifies the node as an interrupt controller.
 - #interrupt-cells: Specifies the number of cells needed to encode an
   interrupt source.