diff options
Diffstat (limited to 'dts/Bindings/gpio')
| -rw-r--r-- | dts/Bindings/gpio/gpio-altera.txt | 4 | ||||
| -rw-r--r-- | dts/Bindings/gpio/gpio-mcp23s08.txt | 4 | ||||
| -rw-r--r-- | dts/Bindings/gpio/gpio-pisosr.txt | 34 | ||||
| -rw-r--r-- | dts/Bindings/gpio/gpio-ts4800.txt | 20 | ||||
| -rw-r--r-- | dts/Bindings/gpio/gpio-xgene-sb.txt | 47 | ||||
| -rw-r--r-- | dts/Bindings/gpio/microchip,pic32-gpio.txt | 49 |
6 files changed, 146 insertions, 12 deletions
diff --git a/dts/Bindings/gpio/gpio-altera.txt b/dts/Bindings/gpio/gpio-altera.txt index 12f50149e1..826a7208ca 100644 --- a/dts/Bindings/gpio/gpio-altera.txt +++ b/dts/Bindings/gpio/gpio-altera.txt @@ -12,7 +12,7 @@ Required properties: - #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware. - The first cell is the GPIO offset number within the GPIO controller. - interrupts: Specify the interrupt. -- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO +- altr,interrupt-type: Specifies the interrupt trigger type the GPIO hardware is synthesized. This field is required if the Altera GPIO controller used has IRQ enabled as the interrupt type is not software controlled, but hardware synthesized. Required if GPIO is used as an interrupt @@ -35,7 +35,7 @@ gpio_altr: gpio@0xff200000 { reg = <0xff200000 0x10>; interrupts = <0 45 4>; altr,ngpio = <32>; - altr,interrupt-trigger = <IRQ_TYPE_EDGE_RISING>; + altr,interrupt-type = <IRQ_TYPE_EDGE_RISING>; #gpio-cells = <2>; gpio-controller; #interrupt-cells = <1>; diff --git a/dts/Bindings/gpio/gpio-mcp23s08.txt b/dts/Bindings/gpio/gpio-mcp23s08.txt index f3332b9a8e..c934106b10 100644 --- a/dts/Bindings/gpio/gpio-mcp23s08.txt +++ b/dts/Bindings/gpio/gpio-mcp23s08.txt @@ -10,6 +10,7 @@ Required properties: - "microchip,mcp23s08" for 8 GPIO SPI version - "microchip,mcp23s17" for 16 GPIO SPI version + - "microchip,mcp23s18" for 16 GPIO SPI version - "microchip,mcp23008" for 8 GPIO I2C version or - "microchip,mcp23017" for 16 GPIO I2C version of the chip NOTE: Do not use the old mcp prefix any more. It is deprecated and will be @@ -43,9 +44,6 @@ Optional properties: - first cell is the pin number - second cell is used to specify flags. - interrupt-controller: Marks the device node as a interrupt controller. -NOTE: The interrupt functionality is only supported for i2c versions of the -chips. The spi chips can also do the interrupts, but this is not supported by -the linux driver yet. Optional device specific properties: - microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices diff --git a/dts/Bindings/gpio/gpio-pisosr.txt b/dts/Bindings/gpio/gpio-pisosr.txt new file mode 100644 index 0000000000..414a01cdf7 --- /dev/null +++ b/dts/Bindings/gpio/gpio-pisosr.txt @@ -0,0 +1,34 @@ +Generic Parallel-in/Serial-out Shift Register GPIO Driver + +This binding describes generic parallel-in/serial-out shift register +devices that can be used for GPI (General Purpose Input). This includes +SN74165 serial-out shift registers and the SN65HVS88x series of +industrial serializers. + +Required properties: + - compatible : Should be "pisosr-gpio". + - gpio-controller : Marks the device node as a GPIO controller. + - #gpio-cells : Should be two. For consumer use see gpio.txt. + +Optional properties: + - ngpios : Number of used GPIO lines (0..n-1), default is 8. + - load-gpios : GPIO pin specifier attached to load enable, this + pin is pulsed before reading from the device to + load input pin values into the the device. + +For other required and optional properties of SPI slave +nodes please refer to ../spi/spi-bus.txt. + +Example: + + gpio@0 { + compatible = "ti,sn65hvs882", "pisosr-gpio"; + gpio-controller; + #gpio-cells = <2>; + + load-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + }; diff --git a/dts/Bindings/gpio/gpio-ts4800.txt b/dts/Bindings/gpio/gpio-ts4800.txt new file mode 100644 index 0000000000..92ea9c8f63 --- /dev/null +++ b/dts/Bindings/gpio/gpio-ts4800.txt @@ -0,0 +1,20 @@ +* TS-4800 FPGA's GPIO controller bindings + +Required properties: +- compatible: Must be "technologic,ts4800-gpio". +- #gpio-cells: Should be two. The first cell is the pin number. +- reg: Physical base address of the controller and length + of memory mapped region. + +Optional property: +- ngpios: See "gpio.txt" + +Example: + +gpio1: gpio { + compatible = "technologic,ts4800-gpio"; + reg = <0x10020 0x6>; + ngpios = <8>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/dts/Bindings/gpio/gpio-xgene-sb.txt b/dts/Bindings/gpio/gpio-xgene-sb.txt index dae1300605..5490c1d689 100644 --- a/dts/Bindings/gpio/gpio-xgene-sb.txt +++ b/dts/Bindings/gpio/gpio-xgene-sb.txt @@ -1,10 +1,20 @@ APM X-Gene Standby GPIO controller bindings -This is a gpio controller in the standby domain. - -There are 20 GPIO pins from 0..21. There is no GPIO_DS14 or GPIO_DS15, -only GPIO_DS8..GPIO_DS13 support interrupts. The IRQ mapping -is currently 1-to-1 on interrupts 0x28 thru 0x2d. +This is a gpio controller in the standby domain. It also supports interrupt in +some particular pins which are sourced to its parent interrupt controller +as diagram below: + +-----------------+ + | X-Gene standby | + | GPIO controller +------ GPIO_0 ++------------+ | | ... +| Parent IRQ | EXT_INT_0 | +------ GPIO_8/EXT_INT_0 +| controller | (SPI40) | | ... +| (GICv2) +--------------+ +------ GPIO_[N+8]/EXT_INT_N +| | ... | | +| | EXT_INT_N | +------ GPIO_[N+9] +| | (SPI[40 + N])| | ... +| +--------------+ +------ GPIO_MAX ++------------+ +-----------------+ Required properties: - compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller @@ -15,10 +25,18 @@ Required properties: 0 = active high 1 = active low - gpio-controller: Marks the device node as a GPIO controller. -- interrupts: Shall contain exactly 6 interrupts. +- interrupts: The EXT_INT_0 parent interrupt resource must be listed first. +- interrupt-parent: Phandle of the parent interrupt controller. +- interrupt-cells: Should be two. + - first cell is 0-N coresponding for EXT_INT_0 to EXT_INT_N. + - second cell is used to specify flags. +- interrupt-controller: Marks the device node as an interrupt controller. +- apm,nr-gpios: Optional, specify number of gpios pin. +- apm,nr-irqs: Optional, specify number of interrupt pins. +- apm,irq-start: Optional, specify lowest gpio pin support interrupt. Example: - sbgpio: sbgpio@17001000 { + sbgpio: gpio@17001000{ compatible = "apm,xgene-gpio-sb"; reg = <0x0 0x17001000 0x0 0x400>; #gpio-cells = <2>; @@ -29,4 +47,19 @@ Example: <0x0 0x2b 0x1>, <0x0 0x2c 0x1>, <0x0 0x2d 0x1>; + interrupt-parent = <&gic>; + #interrupt-cells = <2>; + interrupt-controller; + apm,nr-gpios = <22>; + apm,nr-irqs = <6>; + apm,irq-start = <8>; + }; + + testuser { + compatible = "example,testuser"; + /* Use the GPIO_13/EXT_INT_5 line as an active high triggered + * level interrupt + */ + interrupts = <5 4>; + interrupt-parent = <&sbgpio>; }; diff --git a/dts/Bindings/gpio/microchip,pic32-gpio.txt b/dts/Bindings/gpio/microchip,pic32-gpio.txt new file mode 100644 index 0000000000..ef37528894 --- /dev/null +++ b/dts/Bindings/gpio/microchip,pic32-gpio.txt @@ -0,0 +1,49 @@ +* Microchip PIC32 GPIO devices (PIO). + +Required properties: + - compatible: "microchip,pic32mzda-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + 2 = GPIO_OPEN_DRAIN + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - clocks: Clock specifier (see clock bindings for details). + - microchip,gpio-bank: Specifies which bank a controller owns. + - gpio-ranges: Interaction with the PINCTRL subsystem. + +Example: + +/* PORTA */ +gpio0: gpio0@1f860000 { + compatible = "microchip,pic32mzda-gpio"; + reg = <0x1f860000 0x100>; + interrupts = <118 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&PBCLK4>; + microchip,gpio-bank = <0>; + gpio-ranges = <&pic32_pinctrl 0 0 16>; +}; + +keys { + ... + + button@sw1 { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; |