diff options
Diffstat (limited to 'dts/Bindings/hwmon')
68 files changed, 2720 insertions, 565 deletions
diff --git a/dts/Bindings/hwmon/adi,adm1177.yaml b/dts/Bindings/hwmon/adi,adm1177.yaml index 154bee8511..2e45364d05 100644 --- a/dts/Bindings/hwmon/adi,adm1177.yaml +++ b/dts/Bindings/hwmon/adi,adm1177.yaml @@ -8,7 +8,6 @@ title: Analog Devices ADM1177 Hot Swap Controller and Digital Power Monitor maintainers: - Michael Hennerich <michael.hennerich@analog.com> - - Beniamin Bia <beniamin.bia@analog.com> description: | Analog Devices ADM1177 Hot Swap Controller and Digital Power Monitor @@ -28,7 +27,7 @@ properties: shunt-resistor-micro-ohms: description: - The value of curent sense resistor in microohms. If not provided, + The value of current sense resistor in microohms. If not provided, the current reading and overcurrent alert is disabled. adi,shutdown-threshold-microamp: @@ -53,16 +52,16 @@ examples: - | #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> - i2c0 { + i2c { #address-cells = <1>; #size-cells = <0>; pwmon@5a { - compatible = "adi,adm1177"; - reg = <0x5a>; - shunt-resistor-micro-ohms = <50000>; /* 50 mOhm */ - adi,shutdown-threshold-microamp = <1059000>; /* 1.059 A */ - adi,vrange-high-enable; + compatible = "adi,adm1177"; + reg = <0x5a>; + shunt-resistor-micro-ohms = <50000>; /* 50 mOhm */ + adi,shutdown-threshold-microamp = <1059000>; /* 1.059 A */ + adi,vrange-high-enable; }; }; ... diff --git a/dts/Bindings/hwmon/adi,adm1266.yaml b/dts/Bindings/hwmon/adi,adm1266.yaml index 43b4f4f57b..4f8e11bd51 100644 --- a/dts/Bindings/hwmon/adi,adm1266.yaml +++ b/dts/Bindings/hwmon/adi,adm1266.yaml @@ -39,13 +39,13 @@ additionalProperties: false examples: - | - i2c0 { + i2c { #address-cells = <1>; #size-cells = <0>; adm1266@40 { - compatible = "adi,adm1266"; - reg = <0x40>; + compatible = "adi,adm1266"; + reg = <0x40>; }; }; ... diff --git a/dts/Bindings/hwmon/adi,adm1275.yaml b/dts/Bindings/hwmon/adi,adm1275.yaml index 223393d7ca..ab87f51c5a 100644 --- a/dts/Bindings/hwmon/adi,adm1275.yaml +++ b/dts/Bindings/hwmon/adi,adm1275.yaml @@ -37,6 +37,72 @@ properties: description: Shunt resistor value in micro-Ohm. + adi,volt-curr-sample-average: + description: | + Number of samples to be used to report voltage and current values. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 4, 8, 16, 32, 64, 128] + + adi,power-sample-average: + description: | + Number of samples to be used to report power values. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 4, 8, 16, 32, 64, 128] + +allOf: + - if: + properties: + compatible: + contains: + enum: + - adi,adm1075 + - adi,adm1276 + then: + properties: + adi,volt-curr-sample-average: + default: 128 + adi,power-sample-average: false + + - if: + properties: + compatible: + contains: + enum: + - adi,adm1275 + then: + properties: + adi,volt-curr-sample-average: + default: 16 + adi,power-sample-average: false + + - if: + properties: + compatible: + contains: + enum: + - adi,adm1272 + then: + properties: + adi,volt-curr-sample-average: + default: 128 + adi,power-sample-average: + default: 128 + + - if: + properties: + compatible: + contains: + enum: + - adi,adm1278 + - adi,adm1293 + - adi,adm1294 + then: + properties: + adi,volt-curr-sample-average: + default: 128 + adi,power-sample-average: + default: 1 + required: - compatible - reg @@ -53,5 +119,7 @@ examples: compatible = "adi,adm1272"; reg = <0x10>; shunt-resistor-micro-ohms = <500>; + adi,volt-curr-sample-average = <128>; + adi,power-sample-average = <128>; }; }; diff --git a/dts/Bindings/hwmon/adi,axi-fan-control.yaml b/dts/Bindings/hwmon/adi,axi-fan-control.yaml index 6747b870f2..6751f9b643 100644 --- a/dts/Bindings/hwmon/adi,axi-fan-control.yaml +++ b/dts/Bindings/hwmon/adi,axi-fan-control.yaml @@ -5,13 +5,13 @@ $id: http://devicetree.org/schemas/hwmon/adi,axi-fan-control.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Analog Devices AXI FAN Control Device Tree Bindings +title: Analog Devices AXI FAN Control maintainers: - Nuno Sá <nuno.sa@analog.com> description: |+ - Bindings for the Analog Devices AXI FAN Control driver. Spefications of the + Bindings for the Analog Devices AXI FAN Control driver. Specifications of the core can be found in: https://wiki.analog.com/resources/fpga/docs/axi_fan_control @@ -49,15 +49,15 @@ additionalProperties: false examples: - | fpga_axi: fpga-axi { - #address-cells = <0x2>; - #size-cells = <0x1>; - - axi_fan_control: axi-fan-control@80000000 { - compatible = "adi,axi-fan-control-1.00.a"; - reg = <0x0 0x80000000 0x10000>; - clocks = <&clk 71>; - interrupts = <0 110 0>; - pulses-per-revolution = <2>; - }; + #address-cells = <0x2>; + #size-cells = <0x1>; + + axi_fan_control: axi-fan-control@80000000 { + compatible = "adi,axi-fan-control-1.00.a"; + reg = <0x0 0x80000000 0x10000>; + clocks = <&clk 71>; + interrupts = <0 110 0>; + pulses-per-revolution = <2>; + }; }; ... diff --git a/dts/Bindings/hwmon/adi,ltc2945.yaml b/dts/Bindings/hwmon/adi,ltc2945.yaml new file mode 100644 index 0000000000..5cb66e97e8 --- /dev/null +++ b/dts/Bindings/hwmon/adi,ltc2945.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/adi,ltc2945.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices LTC2945 wide range i2c power monitor + +maintainers: + - Guenter Roeck <linux@roeck-us.net> + +description: | + Analog Devices LTC2945 wide range i2c power monitor over I2C. + + https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2945.pdf + +properties: + compatible: + enum: + - adi,ltc2945 + + reg: + maxItems: 1 + + shunt-resistor-micro-ohms: + description: + Shunt resistor value in micro-Ohms + default: 1000 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + power-monitor@6e { + compatible = "adi,ltc2945"; + reg = <0x6e>; + /* 10 milli-Ohm shunt resistor */ + shunt-resistor-micro-ohms = <10000>; + }; + }; +... diff --git a/dts/Bindings/hwmon/adi,ltc2947.yaml b/dts/Bindings/hwmon/adi,ltc2947.yaml index bf04151b63..152935334c 100644 --- a/dts/Bindings/hwmon/adi,ltc2947.yaml +++ b/dts/Bindings/hwmon/adi,ltc2947.yaml @@ -87,15 +87,15 @@ additionalProperties: false examples: - | spi { - #address-cells = <1>; - #size-cells = <0>; - - ltc2947_spi: ltc2947@0 { - compatible = "adi,ltc2947"; - reg = <0>; - /* accumulation takes place always for energ1/charge1. */ - /* accumulation only on positive current for energy2/charge2. */ - adi,accumulator-ctl-pol = <0 1>; - }; + #address-cells = <1>; + #size-cells = <0>; + + ltc2947_spi: ltc2947@0 { + compatible = "adi,ltc2947"; + reg = <0>; + /* accumulation takes place always for energ1/charge1. */ + /* accumulation only on positive current for energy2/charge2. */ + adi,accumulator-ctl-pol = <0 1>; + }; }; ... diff --git a/dts/Bindings/hwmon/adi,ltc2991.yaml b/dts/Bindings/hwmon/adi,ltc2991.yaml new file mode 100644 index 0000000000..011e5b65c7 --- /dev/null +++ b/dts/Bindings/hwmon/adi,ltc2991.yaml @@ -0,0 +1,128 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/hwmon/adi,ltc2991.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices LTC2991 Octal I2C Voltage, Current and Temperature Monitor + +maintainers: + - Antoniu Miclaus <antoniu.miclaus@analog.com> + +description: | + The LTC2991 is used to monitor system temperatures, voltages and currents. + Through the I2C serial interface, the eight monitors can individually measure + supply voltages and can be paired for differential measurements of current + sense resistors or temperature sensing transistors. + + Datasheet: + https://www.analog.com/en/products/ltc2991.html + +properties: + compatible: + const: adi,ltc2991 + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + vcc-supply: true + +patternProperties: + "^channel@[0-3]$": + type: object + description: + Represents the differential/temperature channels. + + properties: + reg: + description: + The channel number. LTC2991 can monitor 4 currents/temperatures. + items: + minimum: 0 + maximum: 3 + + shunt-resistor-micro-ohms: + description: + The value of curent sense resistor in micro ohms. Pin configuration is + set for differential input pair. + + adi,temperature-enable: + description: + Enables temperature readings. Pin configuration is set for remote + diode temperature measurement. + type: boolean + + required: + - reg + + allOf: + - if: + required: + - shunt-resistor-micro-ohms + then: + properties: + adi,temperature-enable: false + + additionalProperties: false + +required: + - compatible + - reg + - vcc-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hwmon@48 { + compatible = "adi,ltc2991"; + reg = <0x48>; + vcc-supply = <&vcc>; + }; + }; + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hwmon@48 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "adi,ltc2991"; + reg = <0x48>; + vcc-supply = <&vcc>; + + channel@0 { + reg = <0x0>; + shunt-resistor-micro-ohms = <100000>; + }; + + channel@1 { + reg = <0x1>; + shunt-resistor-micro-ohms = <100000>; + }; + + channel@2 { + reg = <0x2>; + adi,temperature-enable; + }; + + channel@3 { + reg = <0x3>; + adi,temperature-enable; + }; + }; + }; +... diff --git a/dts/Bindings/hwmon/adi,ltc2992.yaml b/dts/Bindings/hwmon/adi,ltc2992.yaml index 64a8fcb7bc..0ad12d2456 100644 --- a/dts/Bindings/hwmon/adi,ltc2992.yaml +++ b/dts/Bindings/hwmon/adi,ltc2992.yaml @@ -32,6 +32,7 @@ properties: patternProperties: "^channel@([0-1])$": type: object + additionalProperties: false description: | Represents the two supplies to be monitored. @@ -45,7 +46,7 @@ patternProperties: shunt-resistor-micro-ohms: description: - The value of curent sense resistor in microohms. + The value of current sense resistor in microohms. required: - compatible @@ -55,26 +56,26 @@ additionalProperties: false examples: - | - i2c1 { + i2c { #address-cells = <1>; #size-cells = <0>; - ltc2992@6F { - #address-cells = <1>; - #size-cells = <0>; + ltc2992@6f { + #address-cells = <1>; + #size-cells = <0>; - compatible = "adi,ltc2992"; - reg = <0x6F>; + compatible = "adi,ltc2992"; + reg = <0x6f>; - channel@0 { - reg = <0x0>; - shunt-resistor-micro-ohms = <10000>; - }; + channel@0 { + reg = <0x0>; + shunt-resistor-micro-ohms = <10000>; + }; - channel@1 { - reg = <0x1>; - shunt-resistor-micro-ohms = <10000>; - }; + channel@1 { + reg = <0x1>; + shunt-resistor-micro-ohms = <10000>; + }; }; }; ... diff --git a/dts/Bindings/hwmon/adi,max31760.yaml b/dts/Bindings/hwmon/adi,max31760.yaml new file mode 100644 index 0000000000..9f2d08d7b9 --- /dev/null +++ b/dts/Bindings/hwmon/adi,max31760.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/adi,max31760.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices MAX31760 Fan-Speed Controller + +maintainers: + - Ibrahim Tilki <Ibrahim.Tilki@analog.com> + +description: | + Analog Devices MAX31760 Fan-Speed Controller + https://datasheets.maximintegrated.com/en/ds/MAX31760.pdf + +properties: + compatible: + enum: + - adi,max31760 + + reg: + description: I2C address of slave device. + minimum: 0x50 + maximum: 0x57 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + fan-controller@50 { + reg = <0x50>; + compatible = "adi,max31760"; + }; + }; diff --git a/dts/Bindings/hwmon/adi,max31827.yaml b/dts/Bindings/hwmon/adi,max31827.yaml new file mode 100644 index 0000000000..f60e06ab7d --- /dev/null +++ b/dts/Bindings/hwmon/adi,max31827.yaml @@ -0,0 +1,120 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/adi,max31827.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices MAX31827, MAX31828, MAX31829 Low-Power Temperature Switch + +maintainers: + - Daniel Matyas <daniel.matyas@analog.com> + +description: | + Analog Devices MAX31827, MAX31828, MAX31829 Low-Power Temperature Switch with + I2C Interface + https://www.analog.com/media/en/technical-documentation/data-sheets/MAX31827-MAX31829.pdf + +properties: + compatible: + oneOf: + - const: adi,max31827 + - items: + - enum: + - adi,max31828 + - adi,max31829 + - const: adi,max31827 + + reg: + maxItems: 1 + + vref-supply: + description: + Must have values in the interval (1.6V; 3.6V) in order for the device to + function correctly. + + adi,comp-int: + description: + If present interrupt mode is used. If not present comparator mode is used + (default). + type: boolean + + adi,alarm-pol: + description: + Sets the alarms active state. + - 0 = active low + - 1 = active high + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + + adi,fault-q: + description: + Select how many consecutive temperature faults must occur before + overtemperature or undertemperature faults are indicated in the + corresponding status bits. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 4, 8] + + adi,timeout-enable: + description: + Enables timeout. Bus timeout resets the I2C-compatible interface when SCL + is low for more than 30ms (nominal). + type: boolean + +allOf: + - if: + properties: + compatible: + contains: + const: adi,max31829 + + then: + properties: + adi,alarm-pol: + default: 1 + + else: + properties: + adi,alarm-pol: + default: 0 + + - if: + properties: + compatible: + contains: + const: adi,max31827 + + then: + properties: + adi,fault-q: + default: 1 + + else: + properties: + adi,fault-q: + default: 4 + + +required: + - compatible + - reg + - vref-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + temperature-sensor@42 { + compatible = "adi,max31827"; + reg = <0x42>; + vref-supply = <®_vdd>; + adi,comp-int; + adi,alarm-pol = <0>; + adi,fault-q = <1>; + adi,timeout-enable; + }; + }; +... diff --git a/dts/Bindings/hwmon/adt7475.yaml b/dts/Bindings/hwmon/adt7475.yaml index ad0ec9f35b..051c976ab7 100644 --- a/dts/Bindings/hwmon/adt7475.yaml +++ b/dts/Bindings/hwmon/adt7475.yaml @@ -39,17 +39,7 @@ properties: reg: maxItems: 1 -patternProperties: - "^adi,bypass-attenuator-in[0-4]$": - description: | - Configures bypassing the individual voltage input attenuator. If - set to 1 the attenuator is bypassed if set to 0 the attenuator is - not bypassed. If the property is absent then the attenuator - retains it's configuration from the bios/bootloader. - $ref: /schemas/types.yaml#/definitions/uint32 - enum: [0, 1] - - "^adi,pwm-active-state$": + adi,pwm-active-state: description: | Integer array, represents the active state of the pwm outputs If set to 0 the pwm uses a logic low output for 100% duty cycle. If set to 1 the pwm @@ -61,6 +51,36 @@ patternProperties: enum: [0, 1] default: 1 +patternProperties: + "^adi,bypass-attenuator-in[0-4]$": + description: | + Configures bypassing the individual voltage input attenuator. If + set to 1 the attenuator is bypassed if set to 0 the attenuator is + not bypassed. If the property is absent then the attenuator + retains its configuration from the bios/bootloader. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + + "^adi,pin(5|10)-function$": + description: | + Configures the function for pin 5 on the adi,adt7473 and adi,adt7475. Or + pin 10 on the adi,adt7476 and adi,adt7490. + $ref: /schemas/types.yaml#/definitions/string + enum: + - pwm2 + - smbalert# + + "^adi,pin(9|14)-function$": + description: | + Configures the function for pin 9 on the adi,adt7473 and adi,adt7475. Or + pin 14 on the adi,adt7476 and adi,adt7490 + $ref: /schemas/types.yaml#/definitions/string + enum: + - tach4 + - therm# + - smbalert# + - gpio + required: - compatible - reg @@ -79,6 +99,7 @@ examples: adi,bypass-attenuator-in0 = <1>; adi,bypass-attenuator-in1 = <0>; adi,pwm-active-state = <1 0 1>; + adi,pin10-function = "smbalert#"; + adi,pin14-function = "tach4"; }; }; - diff --git a/dts/Bindings/hwmon/amd,sbrmi.yaml b/dts/Bindings/hwmon/amd,sbrmi.yaml new file mode 100644 index 0000000000..353d81d89b --- /dev/null +++ b/dts/Bindings/hwmon/amd,sbrmi.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/amd,sbrmi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: > + Sideband Remote Management Interface (SB-RMI) compliant + AMD SoC power device. + +maintainers: + - Akshay Gupta <Akshay.Gupta@amd.com> + +description: | + SB Remote Management Interface (SB-RMI) is an SMBus compatible + interface that reports AMD SoC's Power (normalized Power) using, + Mailbox Service Request and resembles a typical 8-pin remote power + sensor's I2C interface to BMC. The power attributes in hwmon + reports power in microwatts. + +properties: + compatible: + enum: + - amd,sbrmi + + reg: + maxItems: 1 + description: | + I2C bus address of the device as specified in Section SBI SMBus Address + of the SoC register reference. The SB-RMI address is normally 78h for + socket 0 and 70h for socket 1, but it could vary based on hardware + address select pins. + \[open source SoC register reference\] + https://www.amd.com/en/support/tech-docs?keyword=55898 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sbrmi@3c { + compatible = "amd,sbrmi"; + reg = <0x3c>; + }; + }; +... diff --git a/dts/Bindings/hwmon/amd,sbtsi.yaml b/dts/Bindings/hwmon/amd,sbtsi.yaml index 446b09f1ce..75088244a2 100644 --- a/dts/Bindings/hwmon/amd,sbtsi.yaml +++ b/dts/Bindings/hwmon/amd,sbtsi.yaml @@ -42,13 +42,13 @@ additionalProperties: false examples: - | - i2c0 { + i2c { #address-cells = <1>; #size-cells = <0>; sbtsi@4c { - compatible = "amd,sbtsi"; - reg = <0x4c>; + compatible = "amd,sbtsi"; + reg = <0x4c>; }; }; ... diff --git a/dts/Bindings/hwmon/aspeed-pwm-tacho.txt b/dts/Bindings/hwmon/aspeed-pwm-tacho.txt index 3ac02988a1..8645cd3b86 100644 --- a/dts/Bindings/hwmon/aspeed-pwm-tacho.txt +++ b/dts/Bindings/hwmon/aspeed-pwm-tacho.txt @@ -45,7 +45,7 @@ Required properties for each child node: - aspeed,fan-tach-ch : should specify the Fan tach input channel. integer value in the range 0 through 15, with 0 indicating Fan tach channel 0 and 15 indicating Fan tach channel 15. - Atleast one Fan tach input channel is required. + At least one Fan tach input channel is required. Examples: diff --git a/dts/Bindings/hwmon/dps650ab.txt b/dts/Bindings/hwmon/dps650ab.txt deleted file mode 100644 index 76780e7958..0000000000 --- a/dts/Bindings/hwmon/dps650ab.txt +++ /dev/null @@ -1,11 +0,0 @@ -Bindings for Delta Electronics DPS-650-AB power supply - -Required properties: -- compatible : "delta,dps650ab" -- reg : I2C address, one of 0x58, 0x59. - -Example: - dps650ab@58 { - compatible = "delta,dps650ab"; - reg = <0x58>; - }; diff --git a/dts/Bindings/hwmon/gpio-fan.txt b/dts/Bindings/hwmon/gpio-fan.txt deleted file mode 100644 index f4cfa350f6..0000000000 --- a/dts/Bindings/hwmon/gpio-fan.txt +++ /dev/null @@ -1,41 +0,0 @@ -Bindings for fan connected to GPIO lines - -Required properties: -- compatible : "gpio-fan" - -Optional properties: -- gpios: Specifies the pins that map to bits in the control value, - ordered MSB-->LSB. -- gpio-fan,speed-map: A mapping of possible fan RPM speeds and the - control value that should be set to achieve them. This array - must have the RPM values in ascending order. -- alarm-gpios: This pin going active indicates something is wrong with - the fan, and a udev event will be fired. -- #cooling-cells: If used as a cooling device, must be <2> - Also see: - Documentation/devicetree/bindings/thermal/thermal-cooling-devices.yaml - min and max states are derived from the speed-map of the fan. - -Note: At least one the "gpios" or "alarm-gpios" properties must be set. - -Examples: - - gpio_fan { - compatible = "gpio-fan"; - gpios = <&gpio1 14 1 - &gpio1 13 1>; - gpio-fan,speed-map = <0 0 - 3000 1 - 6000 2>; - alarm-gpios = <&gpio1 15 1>; - }; - gpio_fan_cool: gpio_fan { - compatible = "gpio-fan"; - gpios = <&gpio2 14 1 - &gpio2 13 1>; - gpio-fan,speed-map = <0 0>, - <3000 1>, - <6000 2>; - alarm-gpios = <&gpio2 15 1>; - #cooling-cells = <2>; /* min followed by max */ - }; diff --git a/dts/Bindings/hwmon/gpio-fan.yaml b/dts/Bindings/hwmon/gpio-fan.yaml new file mode 100644 index 0000000000..7f30cfc873 --- /dev/null +++ b/dts/Bindings/hwmon/gpio-fan.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/gpio-fan.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Fan connected to GPIO lines + +maintainers: + - Rob Herring <robh@kernel.org> + +properties: + compatible: + const: gpio-fan + + gpios: + description: | + Specifies the pins that map to bits in the control value, + ordered MSB-->LSB. + minItems: 1 + maxItems: 7 + + alarm-gpios: + maxItems: 1 + + gpio-fan,speed-map: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + minItems: 2 + maxItems: 127 + items: + items: + - description: fan speed in RPMs + - description: control value + description: | + A mapping of possible fan RPM speeds and the + control value that should be set to achieve them. This array + must have the RPM values in ascending order. + + '#cooling-cells': + const: 2 + +required: + - compatible + - gpios + - gpio-fan,speed-map + +additionalProperties: false + +examples: + - | + gpio-fan { + compatible = "gpio-fan"; + gpios = <&gpio2 14 1 + &gpio2 13 1>; + gpio-fan,speed-map = < 0 0>, + <3000 1>, + <6000 2>; + alarm-gpios = <&gpio2 15 1>; + #cooling-cells = <2>; /* min followed by max */ + }; diff --git a/dts/Bindings/hwmon/hih6130.txt b/dts/Bindings/hwmon/hih6130.txt deleted file mode 100644 index 2c43837af4..0000000000 --- a/dts/Bindings/hwmon/hih6130.txt +++ /dev/null @@ -1,12 +0,0 @@ -Honeywell Humidicon HIH-6130 humidity/temperature sensor --------------------------------------------------------- - -Requires node properties: -- compatible : "honeywell,hi6130" -- reg : the I2C address of the device. This is 0x27. - -Example: - hih6130@27 { - compatible = "honeywell,hih6130"; - reg = <0x27>; - }; diff --git a/dts/Bindings/hwmon/hpe,gxp-fan-ctrl.yaml b/dts/Bindings/hwmon/hpe,gxp-fan-ctrl.yaml new file mode 100644 index 0000000000..4a52aac6be --- /dev/null +++ b/dts/Bindings/hwmon/hpe,gxp-fan-ctrl.yaml @@ -0,0 +1,45 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/hpe,gxp-fan-ctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HPE GXP Fan Controller + +maintainers: + - Nick Hawkins <nick.hawkins@hpe.com> + +description: | + The HPE GXP fan controller controls the fans through an external CPLD + device that connects to the fans. + +properties: + compatible: + const: hpe,gxp-fan-ctrl + + reg: + items: + - description: Fan controller PWM + - description: Programmable logic + - description: Function 2 + + reg-names: + items: + - const: base + - const: pl + - const: fn2 + +required: + - compatible + - reg + - reg-names + +additionalProperties: false + +examples: + - | + fan-controller@1000c00 { + compatible = "hpe,gxp-fan-ctrl"; + reg = <0x1000c00 0x200>, <0xd1000000 0xff>, <0x80200000 0x100000>; + reg-names = "base", "pl", "fn2"; + }; diff --git a/dts/Bindings/hwmon/ibm,cffps1.txt b/dts/Bindings/hwmon/ibm,cffps1.txt deleted file mode 100644 index d9a2719f92..0000000000 --- a/dts/Bindings/hwmon/ibm,cffps1.txt +++ /dev/null @@ -1,26 +0,0 @@ -Device-tree bindings for IBM Common Form Factor Power Supply Versions 1 and 2 ------------------------------------------------------------------------------ - -Required properties: - - compatible : Must be one of the following: - "ibm,cffps1" - "ibm,cffps2" - or "ibm,cffps" if the system - must support any version of the - power supply - - reg = < I2C bus address >; : Address of the power supply on the - I2C bus. - -Example: - - i2c-bus@100 { - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - < more properties > - - power-supply@68 { - compatible = "ibm,cffps1"; - reg = <0x68>; - }; - }; diff --git a/dts/Bindings/hwmon/ibm,occ-hwmon.yaml b/dts/Bindings/hwmon/ibm,occ-hwmon.yaml new file mode 100644 index 0000000000..3dbdc5af28 --- /dev/null +++ b/dts/Bindings/hwmon/ibm,occ-hwmon.yaml @@ -0,0 +1,39 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/ibm,occ-hwmon.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IBM On-Chip Controller (OCC) accessed from a service processor + +maintainers: + - Eddie James <eajames@linux.ibm.com> + +description: | + The POWER processor On-Chip Controller (OCC) helps manage power and + thermals for the system. A service processor or baseboard management + controller can query the OCC for it's power and thermal data to report + through hwmon. + +properties: + compatible: + enum: + - ibm,p9-occ-hwmon + - ibm,p10-occ-hwmon + + ibm,no-poll-on-init: + description: This property describes whether or not the OCC should + be polled during driver initialization. + type: boolean + +required: + - compatible + +additionalProperties: false + +examples: + - | + hwmon { + compatible = "ibm,p10-occ-hwmon"; + ibm,no-poll-on-init; + }; diff --git a/dts/Bindings/hwmon/ibm,p8-occ-hwmon.txt b/dts/Bindings/hwmon/ibm,p8-occ-hwmon.txt new file mode 100644 index 0000000000..5dc5d2e257 --- /dev/null +++ b/dts/Bindings/hwmon/ibm,p8-occ-hwmon.txt @@ -0,0 +1,25 @@ +Device-tree bindings for I2C-based On-Chip Controller hwmon device +------------------------------------------------------------------ + +Required properties: + - compatible = "ibm,p8-occ-hwmon"; + - reg = <I2C address>; : I2C bus address + +Examples: + + i2c-bus@100 { + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <100000>; + < more properties > + + occ-hwmon@1 { + compatible = "ibm,p8-occ-hwmon"; + reg = <0x50>; + }; + + occ-hwmon@2 { + compatible = "ibm,p8-occ-hwmon"; + reg = <0x51>; + }; + }; diff --git a/dts/Bindings/hwmon/iio-hwmon.yaml b/dts/Bindings/hwmon/iio-hwmon.yaml new file mode 100644 index 0000000000..be5c7d4579 --- /dev/null +++ b/dts/Bindings/hwmon/iio-hwmon.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/iio-hwmon.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ADC-attached Hardware Sensor + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: > + Bindings for hardware monitoring devices connected to ADC controllers + supporting the Industrial I/O bindings. + +properties: + compatible: + const: iio-hwmon + + io-channels: + minItems: 1 + maxItems: 51 # Should be enough + description: > + List of phandles to ADC channels to read the monitoring values + +required: + - compatible + - io-channels + +additionalProperties: false + +examples: + - | + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc 1>, <&adc 2>; + }; diff --git a/dts/Bindings/hwmon/ina3221.txt b/dts/Bindings/hwmon/ina3221.txt deleted file mode 100644 index fa63b61714..0000000000 --- a/dts/Bindings/hwmon/ina3221.txt +++ /dev/null @@ -1,54 +0,0 @@ -Texas Instruments INA3221 Device Tree Bindings - -1) ina3221 node - Required properties: - - compatible: Must be "ti,ina3221" - - reg: I2C address - - Optional properties: - - ti,single-shot: This chip has two power modes: single-shot (chip takes one - measurement and then shuts itself down) and continuous ( - chip takes continuous measurements). The continuous mode is - more reliable and suitable for hardware monitor type device, - but the single-shot mode is more power-friendly and useful - for battery-powered device which cares power consumptions - while still needs some measurements occasionally. - If this property is present, the single-shot mode will be - used, instead of the default continuous one for monitoring. - - = The node contains optional child nodes for three channels = - = Each child node describes the information of input source = - - - #address-cells: Required only if a child node is present. Must be 1. - - #size-cells: Required only if a child node is present. Must be 0. - -2) child nodes - Required properties: - - reg: Must be 0, 1 or 2, corresponding to IN1, IN2 or IN3 port of INA3221 - - Optional properties: - - label: Name of the input source - - shunt-resistor-micro-ohms: Shunt resistor value in micro-Ohm - -Example: - -ina3221@40 { - compatible = "ti,ina3221"; - reg = <0x40>; - #address-cells = <1>; - #size-cells = <0>; - - input@0 { - reg = <0x0>; - status = "disabled"; - }; - input@1 { - reg = <0x1>; - shunt-resistor-micro-ohms = <5000>; - }; - input@2 { - reg = <0x2>; - label = "VDD_5V"; - shunt-resistor-micro-ohms = <5000>; - }; -}; diff --git a/dts/Bindings/hwmon/jc42.txt b/dts/Bindings/hwmon/jc42.txt deleted file mode 100644 index f569db58f6..0000000000 --- a/dts/Bindings/hwmon/jc42.txt +++ /dev/null @@ -1,46 +0,0 @@ -Properties for Jedec JC-42.4 compatible temperature sensors - -Required properties: -- compatible: May include a device-specific string consisting of the - manufacturer and the name of the chip. A list of supported - chip names follows. - Must include "jedec,jc-42.4-temp" for any Jedec JC-42.4 - compatible temperature sensor. - - Supported chip names: - adi,adt7408 - atmel,at30ts00 - atmel,at30tse004 - onnn,cat6095 - onnn,cat34ts02 - maxim,max6604 - microchip,mcp9804 - microchip,mcp9805 - microchip,mcp9808 - microchip,mcp98243 - microchip,mcp98244 - microchip,mcp9843 - nxp,se97 - nxp,se98 - st,stts2002 - st,stts2004 - st,stts3000 - st,stts424 - st,stts424e - idt,tse2002 - idt,tse2004 - idt,ts3000 - idt,ts3001 - -- reg: I2C address - -Optional properties: -- smbus-timeout-disable: When set, the smbus timeout function will be disabled. - This is not supported on all chips. - -Example: - -temp-sensor@1a { - compatible = "jedec,jc-42.4-temp"; - reg = <0x1a>; -}; diff --git a/dts/Bindings/hwmon/jedec,jc42.yaml b/dts/Bindings/hwmon/jedec,jc42.yaml new file mode 100644 index 0000000000..bf3332153a --- /dev/null +++ b/dts/Bindings/hwmon/jedec,jc42.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/jedec,jc42.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Jedec JC-42.4 compatible temperature sensors + +maintainers: + - Jean Delvare <jdelvare@suse.com> + - Guenter Roeck <linux@roeck-us.net> + +select: + properties: + compatible: + const: jedec,jc-42.4-temp + + required: + - compatible + +properties: + compatible: + oneOf: + - const: jedec,jc-42.4-temp + - items: + - enum: + - adi,adt7408 + - atmel,at30ts00 + - atmel,at30tse004 + - idt,tse2002 + - idt,tse2004 + - idt,ts3000 + - idt,ts3001 + - maxim,max6604 + - microchip,mcp9804 + - microchip,mcp9805 + - microchip,mcp9808 + - microchip,mcp98243 + - microchip,mcp98244 + - microchip,mcp9843 + - nxp,se97 + - nxp,se97b + - nxp,se98 + - onnn,cat6095 + - onnn,cat34ts02 + - st,stts2002 + - st,stts2004 + - st,stts3000 + - st,stts424 + - st,stts424e + - const: jedec,jc-42.4-temp + + reg: + maxItems: 1 + + smbus-timeout-disable: + description: | + When set, the smbus timeout function will be disabled. This is not + supported on all chips. + type: boolean + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + temp-sensor@1a { + compatible = "jedec,jc-42.4-temp"; + reg = <0x1a>; + }; + }; diff --git a/dts/Bindings/hwmon/lltc,ltc4151.yaml b/dts/Bindings/hwmon/lltc,ltc4151.yaml new file mode 100644 index 0000000000..e62aff6704 --- /dev/null +++ b/dts/Bindings/hwmon/lltc,ltc4151.yaml @@ -0,0 +1,41 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/lltc,ltc4151.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LTC4151 High Voltage I2C Current and Voltage Monitor + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + const: lltc,ltc4151 + + reg: + maxItems: 1 + + shunt-resistor-micro-ohms: + description: + Shunt resistor value in micro-Ohms + default: 1000 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@6e { + compatible = "lltc,ltc4151"; + reg = <0x6e>; + shunt-resistor-micro-ohms = <1500>; + }; + }; diff --git a/dts/Bindings/hwmon/lltc,ltc4286.yaml b/dts/Bindings/hwmon/lltc,ltc4286.yaml new file mode 100644 index 0000000000..98ca163d34 --- /dev/null +++ b/dts/Bindings/hwmon/lltc,ltc4286.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/lltc,ltc4286.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LTC4286 power monitors + +maintainers: + - Delphine CC Chiu <Delphine_CC_Chiu@Wiwynn.com> + +properties: + compatible: + enum: + - lltc,ltc4286 + - lltc,ltc4287 + + reg: + maxItems: 1 + + adi,vrange-low-enable: + description: + This property is a bool parameter to represent the + voltage range is 25.6 volts or 102.4 volts for this chip. + The default is 102.4 volts. + type: boolean + + shunt-resistor-micro-ohms: + description: + Resistor value micro-ohms. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + power-monitor@40 { + compatible = "lltc,ltc4286"; + reg = <0x40>; + adi,vrange-low-enable; + shunt-resistor-micro-ohms = <300>; + }; + }; diff --git a/dts/Bindings/hwmon/lm70.txt b/dts/Bindings/hwmon/lm70.txt deleted file mode 100644 index ea417a0d32..0000000000 --- a/dts/Bindings/hwmon/lm70.txt +++ /dev/null @@ -1,22 +0,0 @@ -* LM70/TMP121/LM71/LM74 thermometer. - -Required properties: -- compatible: one of - "ti,lm70" - "ti,tmp121" - "ti,tmp122" - "ti,lm71" - "ti,lm74" - -See Documentation/devicetree/bindings/spi/spi-bus.txt for more required and -optional properties. - -Example: - -spi_master { - temperature-sensor@0 { - compatible = "ti,lm70"; - reg = <0>; - spi-max-frequency = <1000000>; - }; -}; diff --git a/dts/Bindings/hwmon/lm75.yaml b/dts/Bindings/hwmon/lm75.yaml index 96eed5cc78..ed269e428a 100644 --- a/dts/Bindings/hwmon/lm75.yaml +++ b/dts/Bindings/hwmon/lm75.yaml @@ -1,4 +1,4 @@ -# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause %YAML 1.2 --- $id: http://devicetree.org/schemas/hwmon/lm75.yaml# @@ -14,6 +14,8 @@ properties: compatible: enum: - adi,adt75 + - ams,as6200 + - atmel,at30ts74 - dallas,ds1775 - dallas,ds75 - dallas,ds7505 @@ -30,6 +32,7 @@ properties: - st,stds75 - st,stlm75 - microchip,tcn75 + - ti,tmp1075 - ti,tmp100 - ti,tmp101 - ti,tmp105 @@ -46,10 +49,28 @@ properties: vs-supply: description: phandle to the regulator that provides the +VS supply + interrupts: + maxItems: 1 + required: - compatible - reg +allOf: + - if: + not: + properties: + compatible: + contains: + enum: + - ams,as6200 + - ti,tmp100 + - ti,tmp101 + - ti,tmp112 + then: + properties: + interrupts: false + additionalProperties: false examples: @@ -64,3 +85,17 @@ examples: vs-supply = <&vs>; }; }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + temperature-sensor@48 { + compatible = "ams,as6200"; + reg = <0x48>; + vs-supply = <&vs>; + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_BOTH>; + }; + }; diff --git a/dts/Bindings/hwmon/lm87.txt b/dts/Bindings/hwmon/lm87.txt index e1b79903f2..758ff398b6 100644 --- a/dts/Bindings/hwmon/lm87.txt +++ b/dts/Bindings/hwmon/lm87.txt @@ -18,7 +18,7 @@ optional properties: in7. Otherwise the pin is set as FAN2 input. - vcc-supply: a Phandle for the regulator supplying power, can be - cofigured to measure 5.0V power supply. Default is 3.3V. + configured to measure 5.0V power supply. Default is 3.3V. Example: diff --git a/dts/Bindings/hwmon/lm90.txt b/dts/Bindings/hwmon/lm90.txt deleted file mode 100644 index 398dcb9657..0000000000 --- a/dts/Bindings/hwmon/lm90.txt +++ /dev/null @@ -1,51 +0,0 @@ -* LM90 series thermometer. - -Required node properties: -- compatible: manufacturer and chip name, one of - "adi,adm1032" - "adi,adt7461" - "adi,adt7461a" - "gmt,g781" - "national,lm90" - "national,lm86" - "national,lm89" - "national,lm99" - "dallas,max6646" - "dallas,max6647" - "dallas,max6649" - "dallas,max6657" - "dallas,max6658" - "dallas,max6659" - "dallas,max6680" - "dallas,max6681" - "dallas,max6695" - "dallas,max6696" - "onnn,nct1008" - "winbond,w83l771" - "nxp,sa56004" - "ti,tmp451" - -- reg: I2C bus address of the device - -- vcc-supply: vcc regulator for the supply voltage. - -Optional properties: -- interrupts: Contains a single interrupt specifier which describes the - LM90 "-ALERT" pin output. - See interrupt-controller/interrupts.txt for the format. - -- #thermal-sensor-cells: should be set to 1. See thermal/thermal-sensor.yaml - for details. See <include/dt-bindings/thermal/lm90.h> for the - definition of the local, remote and 2nd remote sensor index - constants. - -Example LM90 node: - -temp-sensor { - compatible = "onnn,nct1008"; - reg = <0x4c>; - vcc-supply = <&palmas_ldo6_reg>; - interrupt-parent = <&gpio>; - interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>; - #thermal-sensor-cells = <1>; -} diff --git a/dts/Bindings/hwmon/ltc4151.txt b/dts/Bindings/hwmon/ltc4151.txt deleted file mode 100644 index d008a5ef52..0000000000 --- a/dts/Bindings/hwmon/ltc4151.txt +++ /dev/null @@ -1,18 +0,0 @@ -LTC4151 High Voltage I2C Current and Voltage Monitor - -Required properties: -- compatible: Must be "lltc,ltc4151" -- reg: I2C address - -Optional properties: -- shunt-resistor-micro-ohms - Shunt resistor value in micro-Ohms - Defaults to <1000> if unset. - -Example: - -ltc4151@6e { - compatible = "lltc,ltc4151"; - reg = <0x6e>; - shunt-resistor-micro-ohms = <1500>; -}; diff --git a/dts/Bindings/hwmon/ltq-cputemp.txt b/dts/Bindings/hwmon/ltq-cputemp.txt index 33fd00a987..473b34c876 100644 --- a/dts/Bindings/hwmon/ltq-cputemp.txt +++ b/dts/Bindings/hwmon/ltq-cputemp.txt @@ -1,4 +1,4 @@ -Lantiq cpu temperatur sensor +Lantiq cpu temperature sensor Requires node properties: - compatible value : diff --git a/dts/Bindings/hwmon/max1619.txt b/dts/Bindings/hwmon/max1619.txt deleted file mode 100644 index c70dbbe1e5..0000000000 --- a/dts/Bindings/hwmon/max1619.txt +++ /dev/null @@ -1,12 +0,0 @@ -Bindings for MAX1619 Temperature Sensor - -Required properties: -- compatible : "maxim,max1619" -- reg : I2C address, one of 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, or - 0x4d, 0x4e - -Example: - temp@4c { - compatible = "maxim,max1619"; - reg = <0x4c>; - }; diff --git a/dts/Bindings/hwmon/mcp3021.txt b/dts/Bindings/hwmon/mcp3021.txt deleted file mode 100644 index 294318ba69..0000000000 --- a/dts/Bindings/hwmon/mcp3021.txt +++ /dev/null @@ -1,21 +0,0 @@ -mcp3021 properties - -Required properties: -- compatible: Must be one of the following: - - "microchip,mcp3021" for mcp3021 - - "microchip,mcp3221" for mcp3221 -- reg: I2C address - -Optional properties: - -- reference-voltage-microvolt - Reference voltage in microvolt (uV) - -Example: - -mcp3021@4d { - compatible = "microchip,mcp3021"; - reg = <0x4d>; - - reference-voltage-microvolt = <4500000>; /* 4.5 V */ -}; diff --git a/dts/Bindings/hwmon/microchip,lan966x.yaml b/dts/Bindings/hwmon/microchip,lan966x.yaml new file mode 100644 index 0000000000..390dd6755f --- /dev/null +++ b/dts/Bindings/hwmon/microchip,lan966x.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/microchip,lan966x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip LAN966x Hardware Monitor + +maintainers: + - Michael Walle <michael@walle.cc> + +description: | + Microchip LAN966x temperature monitor and fan controller + +properties: + compatible: + enum: + - microchip,lan9668-hwmon + + reg: + items: + - description: PVT registers + - description: FAN registers + + reg-names: + items: + - const: pvt + - const: fan + + clocks: + maxItems: 1 + + '#thermal-sensor-cells': + const: 0 + +required: + - compatible + - reg + - reg-names + - clocks + +additionalProperties: false + +examples: + - | + hwmon: hwmon@e2010180 { + compatible = "microchip,lan9668-hwmon"; + reg = <0xe2010180 0xc>, + <0xe20042a8 0xc>; + reg-names = "pvt", "fan"; + clocks = <&sys_clk>; + #thermal-sensor-cells = <0>; + }; diff --git a/dts/Bindings/hwmon/microchip,mcp3021.yaml b/dts/Bindings/hwmon/microchip,mcp3021.yaml new file mode 100644 index 0000000000..f5e104c1b0 --- /dev/null +++ b/dts/Bindings/hwmon/microchip,mcp3021.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/microchip,mcp3021.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip MCP3021 A/D converter + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + enum: + - microchip,mcp3021 + - microchip,mcp3221 + + reg: + maxItems: 1 + + reference-voltage-microvolt: + description: + VDD supply power and reference voltage + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + adc@4d { + compatible = "microchip,mcp3021"; + reg = <0x4d>; + + reference-voltage-microvolt = <4500000>; /* 4.5 V */ + }; + }; diff --git a/dts/Bindings/hwmon/microchip,sparx5-temp.yaml b/dts/Bindings/hwmon/microchip,sparx5-temp.yaml index 76be625d56..51e8619dbf 100644 --- a/dts/Bindings/hwmon/microchip,sparx5-temp.yaml +++ b/dts/Bindings/hwmon/microchip,sparx5-temp.yaml @@ -22,7 +22,7 @@ properties: clocks: items: - - description: AHB reference clock + - description: System reference clock '#thermal-sensor-cells': const: 0 @@ -40,5 +40,5 @@ examples: compatible = "microchip,sparx5-temp"; reg = <0x10508110 0xc>; #thermal-sensor-cells = <0>; - clocks = <&ahb_clk>; + clocks = <&sys_clk>; }; diff --git a/dts/Bindings/hwmon/moortec,mr75203.yaml b/dts/Bindings/hwmon/moortec,mr75203.yaml index b79f069a04..56db2292f0 100644 --- a/dts/Bindings/hwmon/moortec,mr75203.yaml +++ b/dts/Bindings/hwmon/moortec,mr75203.yaml @@ -4,11 +4,37 @@ $id: http://devicetree.org/schemas/hwmon/moortec,mr75203.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Moortec Semiconductor MR75203 PVT Controller bindings +title: Moortec Semiconductor MR75203 PVT Controller maintainers: - Rahul Tanwar <rtanwar@maxlinear.com> +description: | + A Moortec PVT (Process, Voltage, Temperature) monitoring logic design can + include many different units. + Such a design will usually consists of several Moortec's embedded analog IPs, + and a single Moortec controller (mr75203) to configure and control the IPs. + + Some of the Moortec's analog hard IPs that can be used in a design: + *) Temperature Sensor (TS) - used to monitor core temperature (e.g. mr74137). + *) Voltage Monitor (VM) - used to monitor voltage levels (e.g. mr74138). + *) Process Detector (PD) - used to assess silicon speed (e.g. mr74139). + *) Delay Chain - ring oscillator connected to the PD, used to measure IO + based transistors (e.g. mr76008 ring oscillator at 1.1V, mr76007 ring + oscillator at 1.8V). + *) Pre Scaler - provides divide-by-X scaling of input voltage, which can then + be presented for VM for measurement within its range (e.g. mr76006 - + divide by 2 pre-scaler). + + TS, VM & PD also include a digital interface, which consists of configuration + inputs and measurement outputs. + + Some of the units have number of series, each series can have slightly + different characteristics. + + The mr75203 binding describes configuration for the controller unit, but also + for some of the analog IPs. + properties: compatible: const: moortec,mr75203 @@ -16,7 +42,7 @@ properties: reg: items: - description: PVT common registers - - description: PVT temprature sensor registers + - description: PVT temperature sensor registers - description: PVT process detector registers - description: PVT voltage monitor registers @@ -44,13 +70,76 @@ properties: "#thermal-sensor-cells": const: 1 + moortec,vm-active-channels: + description: + Defines the number of channels per VM that are actually used and are + connected to some input source. + Maximum number of items - number of VMs. + Maximum value of each item - number of channels. + Minimum value of each item - 0 (which means entire VM sensor is not used). + $ref: /schemas/types.yaml#/definitions/uint8-array + + moortec,vm-pre-scaler-x2: + description: + Defines the channels that use a mr76006 pre-scaler to divide the input + source by 2. + The pre-scaler is used for input sources that exceed the VM input range. + The driver uses this information to present to the user with the actual + value of the voltage source. + For channels that are not listed, no pre-scaler is assumed. + Maximum number of items - total number of channels in all VMs. + Each channel should not appear more than once. + $ref: /schemas/types.yaml#/definitions/uint8-array + + moortec,ts-series: + description: + Definition of the temperature equation and coefficients that shall be + used to convert the digital output to value in milli-Celsius. + minimum: 5 + maximum: 6 + default: 5 + $ref: /schemas/types.yaml#/definitions/uint32 + + moortec,ts-coeff-g: + description: + G coefficient for temperature equation. + Default for series 5 = 60000 + Default for series 6 = 57400 + multipleOf: 100 + minimum: 1000 + $ref: /schemas/types.yaml#/definitions/uint32 + + moortec,ts-coeff-h: + description: + H coefficient for temperature equation. + Default for series 5 = 200000 + Default for series 6 = 249400 + multipleOf: 100 + minimum: 1000 + $ref: /schemas/types.yaml#/definitions/uint32 + + moortec,ts-coeff-cal5: + description: + cal5 coefficient for temperature equation. + Default for series 5 = 4094 + Default for series 6 = 4096 + minimum: 1 + $ref: /schemas/types.yaml#/definitions/uint32 + + moortec,ts-coeff-j: + description: + J coefficient for temperature equation. + Default for series 5 = -100 + Default for series 6 = 0 + multipleOf: 100 + maximum: 0 + $ref: /schemas/types.yaml#/definitions/int32 + required: - compatible - reg - reg-names - - intel,vm-map - clocks - - resets - "#thermal-sensor-cells" additionalProperties: false @@ -67,5 +156,9 @@ examples: intel,vm-map = [03 01 04 ff ff]; clocks = <&osc0>; resets = <&rcu0 0x40 7>; + moortec,vm-active-channels = /bits/ 8 <0x10 0x05>; + moortec,vm-pre-scaler-x2 = /bits/ 8 <5 6 20>; + moortec,ts-coeff-g = <61400>; + moortec,ts-coeff-h = <253700>; #thermal-sensor-cells = <1>; }; diff --git a/dts/Bindings/hwmon/national,lm90.yaml b/dts/Bindings/hwmon/national,lm90.yaml new file mode 100644 index 0000000000..6e59c8fdef --- /dev/null +++ b/dts/Bindings/hwmon/national,lm90.yaml @@ -0,0 +1,227 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/national,lm90.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LM90 series thermometer + +maintainers: + - Jean Delvare <jdelvare@suse.com> + - Guenter Roeck <linux@roeck-us.net> + +properties: + compatible: + enum: + - adi,adm1032 + - adi,adt7461 + - adi,adt7461a + - adi,adt7481 + - dallas,max6646 + - dallas,max6647 + - dallas,max6649 + - dallas,max6657 + - dallas,max6658 + - dallas,max6659 + - dallas,max6680 + - dallas,max6681 + - dallas,max6695 + - dallas,max6696 + - gmt,g781 + - national,lm86 + - national,lm89 + - national,lm90 + - national,lm99 + - nxp,sa56004 + - onnn,nct1008 + - ti,tmp451 + - ti,tmp461 + - winbond,w83l771 + + + interrupts: + items: + - description: | + Single interrupt specifier which describes the LM90 "-ALERT" pin + output. + + reg: + maxItems: 1 + + "#thermal-sensor-cells": + const: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + vcc-supply: + description: phandle to the regulator that provides the +VCC supply + + ti,extended-range-enable: + description: Set to enable extended range temperature. + type: boolean + +required: + - compatible + - reg + +patternProperties: + "^channel@([0-2])$": + type: object + description: Represents channels of the device and their specific configuration. + + properties: + reg: + description: The channel number. 0 is local channel, 1-2 are remote channels. + items: + minimum: 0 + maximum: 2 + + label: + description: A descriptive name for this channel, like "ambient" or "psu". + + temperature-offset-millicelsius: + description: Temperature offset to be added to or subtracted from remote temperature measurements. + + required: + - reg + + additionalProperties: false + +allOf: + - if: + not: + properties: + compatible: + contains: + enum: + - adi,adt7461 + - adi,adt7461a + - adi,adt7481 + - ti,tmp451 + - ti,tmp461 + then: + properties: + ti,extended-range-enable: false + + - if: + properties: + compatible: + contains: + enum: + - dallas,max6646 + - dallas,max6647 + - dallas,max6649 + - dallas,max6657 + - dallas,max6658 + - dallas,max6659 + - dallas,max6695 + - dallas,max6696 + then: + patternProperties: + "^channel@([0-2])$": + properties: + temperature-offset-millicelsius: false + + - if: + properties: + compatible: + contains: + enum: + - adi,adt7461 + - adi,adt7461a + - adi,adt7481 + - onnn,nct1008 + then: + patternProperties: + "^channel@([0-2])$": + properties: + temperature-offset-millicelsius: + maximum: 127750 + + - if: + properties: + compatible: + contains: + enum: + - adi,adm1032 + - dallas,max6680 + - dallas,max6681 + - gmt,g781 + - national,lm86 + - national,lm89 + - national,lm90 + - national,lm99 + - nxp,sa56004 + - winbond,w83l771 + then: + patternProperties: + "^channel@([0-2])$": + properties: + temperature-offset-millicelsius: + maximum: 127875 + + - if: + properties: + compatible: + contains: + enum: + - ti,tmp451 + - ti,tmp461 + then: + patternProperties: + "^channel@([0-2])$": + properties: + temperature-offset-millicelsius: + maximum: 127937 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@4c { + compatible = "onnn,nct1008"; + reg = <0x4c>; + vcc-supply = <&palmas_ldo6_reg>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + #thermal-sensor-cells = <1>; + }; + }; + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@4c { + compatible = "adi,adt7481"; + reg = <0x4c>; + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0x0>; + label = "local"; + }; + + channel@1 { + reg = <0x1>; + label = "front"; + temperature-offset-millicelsius = <4000>; + }; + + channel@2 { + reg = <0x2>; + label = "back"; + temperature-offset-millicelsius = <750>; + }; + }; + }; diff --git a/dts/Bindings/hwmon/npcm750-pwm-fan.txt b/dts/Bindings/hwmon/npcm750-pwm-fan.txt index 28f43e929f..18095ba87a 100644 --- a/dts/Bindings/hwmon/npcm750-pwm-fan.txt +++ b/dts/Bindings/hwmon/npcm750-pwm-fan.txt @@ -1,12 +1,16 @@ -Nuvoton NPCM7xx PWM and Fan Tacho controller device +Nuvoton NPCM PWM and Fan Tacho controller device The Nuvoton BMC NPCM7XX supports 8 Pulse-width modulation (PWM) controller outputs and 16 Fan tachometer controller inputs. +The Nuvoton BMC NPCM8XX supports 12 Pulse-width modulation (PWM) +controller outputs and 16 Fan tachometer controller inputs. + Required properties for pwm-fan node - #address-cells : should be 1. - #size-cells : should be 0. - compatible : "nuvoton,npcm750-pwm-fan" for Poleg NPCM7XX. + : "nuvoton,npcm845-pwm-fan" for Arbel NPCM8XX. - reg : specifies physical base address and size of the registers. - reg-names : must contain: * "pwm" for the PWM registers. @@ -23,7 +27,7 @@ Required properties for pwm-fan node fan subnode format: =================== Under fan subnode can be upto 8 child nodes, each child node representing a fan. -Each fan subnode must have one PWM channel and atleast one Fan tach channel. +Each fan subnode must have one PWM channel and at least one Fan tach channel. For PWM channel can be configured cooling-levels to create cooling device. Cooling device could be bound to a thermal zone for the thermal control. diff --git a/dts/Bindings/hwmon/ntc-thermistor.yaml b/dts/Bindings/hwmon/ntc-thermistor.yaml new file mode 100644 index 0000000000..3d0146e20d --- /dev/null +++ b/dts/Bindings/hwmon/ntc-thermistor.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +--- +$id: http://devicetree.org/schemas/hwmon/ntc-thermistor.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NTC thermistor temperature sensors + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + Thermistors with negative temperature coefficient (NTC) are resistors that + vary in resistance in an often non-linear way in relation to temperature. + The negative temperature coefficient means that the resistance decreases + as the temperature rises. Since the relationship between resistance and + temperature is non-linear, software drivers most often need to use a look + up table and interpolation to get from resistance to temperature. + + When used in practice, a thermistor is often connected between ground, a + pull-up resistor or/and a pull-down resistor and a fixed voltage like this: + + + e.g. 5V = pull-up voltage (puv) + | + +-+ + | | + | | Pull-up resistor + | | (puo) + +-+ + |-------------------------o + +-+ | ^ + | |/ | + | / | + |/| Thermistor | Measured voltage (mv) + / | | "connected ground" + /| | | + +-+ | + |-------------------------o + +-+ ^ + | | | + | | Pull-down resistor | Measured voltage (mv) + | | (pdo) | "connected positive" + +-+ | + | | + | v + + GND GND + + The arrangements of where we measure the voltage over the thermistor are + called "connected ground" and "connected positive" and shall be understood as + the cases when either pull-up or pull-down resistance is zero. + + If the pull-up resistance is 0 one end of the thermistor is connected to the + positive voltage and we get the thermistor on top of a pull-down resistor + and we take the measure between the thermistor and the pull-down resistor. + + Conversely if the pull-down resistance is zero, one end of the thermistor is + connected to ground and we get the thermistor under the pull-up resistor + and we take the measure between the pull-up resistor and the thermistor. + + We can use both pull-up and pull-down resistors at the same time, and then + the figure illustrates where the voltage will be measured for the "connected + ground" and "connected positive" cases. + +properties: + $nodename: + pattern: "^thermistor(.*)?$" + + compatible: + oneOf: + - const: epcos,b57330v2103 + - const: epcos,b57891s0103 + - const: murata,ncp15wb473 + - const: murata,ncp18wb473 + - const: murata,ncp21wb473 + - const: murata,ncp03wb473 + - const: murata,ncp15wl333 + - const: murata,ncp03wf104 + - const: murata,ncp15xh103 + - const: samsung,1404-001221 + # Deprecated "ntp," compatible strings + - const: ntc,ncp15wb473 + deprecated: true + - const: ntc,ncp18wb473 + deprecated: true + - const: ntc,ncp21wb473 + deprecated: true + - const: ntc,ncp03wb473 + deprecated: true + - const: ntc,ncp15wl333 + deprecated: true + + "#thermal-sensor-cells": + description: Thermal sensor cells if used for thermal sensoring. + const: 0 + + pullup-uv: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Pull-up voltage in micro volts. Must always be specified. + + pullup-ohm: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Pull-up resistance in ohms. Must always be specified, even + if zero. + + pulldown-ohm: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Pull-down resistance in ohms. Must always be specified, even + if zero. + + connected-positive: + $ref: /schemas/types.yaml#/definitions/flag + description: Indicates how the thermistor is connected in series with + a pull-up and/or a pull-down resistor. See the description above for + an illustration. If this flag is NOT specified, the thermistor is assumed + to be connected-ground, which usually means a pull-down resistance of + zero but complex arrangements are possible. + + # See /schemas/iio/adc/adc.yaml + io-channels: + maxItems: 1 + description: IIO ADC channel to read the voltage over the resistor. Must + always be specified. + +required: + - compatible + - pullup-uv + - pullup-ohm + - pulldown-ohm + - io-channels + +additionalProperties: false + +examples: + - | + thermistor { + compatible = "murata,ncp18wb473"; + io-channels = <&gpadc 0x06>; + pullup-uv = <1800000>; + pullup-ohm = <220000>; + pulldown-ohm = <0>; + #thermal-sensor-cells = <0>; + }; diff --git a/dts/Bindings/hwmon/ntc_thermistor.txt b/dts/Bindings/hwmon/ntc_thermistor.txt deleted file mode 100644 index 4c5c371297..0000000000 --- a/dts/Bindings/hwmon/ntc_thermistor.txt +++ /dev/null @@ -1,44 +0,0 @@ -NTC Thermistor hwmon sensors -------------------------------- - -Requires node properties: -- "compatible" value : one of - "epcos,b57330v2103" - "epcos,b57891s0103" - "murata,ncp15wb473" - "murata,ncp18wb473" - "murata,ncp21wb473" - "murata,ncp03wb473" - "murata,ncp15wl333" - "murata,ncp03wf104" - "murata,ncp15xh103" - -/* Usage of vendor name "ntc" is deprecated */ -<DEPRECATED> "ntc,ncp15wb473" -<DEPRECATED> "ntc,ncp18wb473" -<DEPRECATED> "ntc,ncp21wb473" -<DEPRECATED> "ntc,ncp03wb473" -<DEPRECATED> "ntc,ncp15wl333" - -- "pullup-uv" Pull up voltage in micro volts -- "pullup-ohm" Pull up resistor value in ohms -- "pulldown-ohm" Pull down resistor value in ohms -- "connected-positive" Always ON, If not specified. - Status change is possible. -- "io-channels" Channel node of ADC to be used for - conversion. - -Optional node properties: -- "#thermal-sensor-cells" Used to expose itself to thermal fw. - -Read more about iio bindings at - https://github.com/devicetree-org/dt-schema/blob/master/schemas/iio/ - -Example: - ncp15wb473@0 { - compatible = "murata,ncp15wb473"; - pullup-uv = <1800000>; - pullup-ohm = <47000>; - pulldown-ohm = <0>; - io-channels = <&adc 3>; - }; diff --git a/dts/Bindings/hwmon/nuvoton,nct6775.yaml b/dts/Bindings/hwmon/nuvoton,nct6775.yaml new file mode 100644 index 0000000000..358b262431 --- /dev/null +++ b/dts/Bindings/hwmon/nuvoton,nct6775.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/hwmon/nuvoton,nct6775.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nuvoton NCT6775 and compatible Super I/O chips + +maintainers: + - Zev Weiss <zev@bewilderbeest.net> + +properties: + compatible: + enum: + - nuvoton,nct6106 + - nuvoton,nct6116 + - nuvoton,nct6775 + - nuvoton,nct6776 + - nuvoton,nct6779 + - nuvoton,nct6791 + - nuvoton,nct6792 + - nuvoton,nct6793 + - nuvoton,nct6795 + - nuvoton,nct6796 + - nuvoton,nct6797 + - nuvoton,nct6798 + + reg: + maxItems: 1 + + nuvoton,tsi-channel-mask: + description: + Bitmask indicating which TSI temperature sensor channels are + active. LSB is TSI0, bit 1 is TSI1, etc. + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 0xff + default: 0 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + superio@4d { + compatible = "nuvoton,nct6779"; + reg = <0x4d>; + nuvoton,tsi-channel-mask = <0x03>; + }; + }; diff --git a/dts/Bindings/hwmon/nuvoton,nct7802.yaml b/dts/Bindings/hwmon/nuvoton,nct7802.yaml new file mode 100644 index 0000000000..cd8dcd7970 --- /dev/null +++ b/dts/Bindings/hwmon/nuvoton,nct7802.yaml @@ -0,0 +1,145 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/hwmon/nuvoton,nct7802.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nuvoton NCT7802Y Hardware Monitoring IC + +maintainers: + - Guenter Roeck <linux@roeck-us.net> + +description: | + The NCT7802Y is a hardware monitor IC which supports one on-die and up to + 5 remote temperature sensors with SMBus interface. + + Datasheets: + https://www.nuvoton.com/export/resource-files/Nuvoton_NCT7802Y_Datasheet_V12.pdf + +additionalProperties: false + +properties: + compatible: + enum: + - nuvoton,nct7802 + + reg: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^channel@[0-3]$": + type: object + + additionalProperties: false + + properties: + reg: + items: + - enum: + - 0 # Local Temperature Sensor ("LTD") + - 1 # Remote Temperature Sensor or Voltage Sensor 1 ("RTD1") + - 2 # Remote Temperature Sensor or Voltage Sensor 2 ("RTD2") + - 3 # Remote Temperature Sensor or Voltage Sensor 3 ("RTD3") + + sensor-type: + items: + - enum: + - temperature + - voltage + + temperature-mode: + items: + - enum: + - thermistor + - thermal-diode + + required: + - reg + + allOf: + # For channels RTD1, RTD2 and RTD3, require sensor-type to be set. + # Otherwise (for all other channels), do not allow temperature-mode to be + # set. + - if: + properties: + reg: + items: + - enum: + - 1 + - 2 + - 3 + then: + required: + - sensor-type + else: + not: + required: + - sensor-type + + # For channels RTD1 and RTD2 and if sensor-type is "temperature", require + # temperature-mode to be set. Otherwise (for all other channels or + # sensor-type settings), do not allow temperature-mode to be set + - if: + properties: + reg: + items: + - enum: + - 1 + - 2 + sensor-type: + items: + - enum: + - temperature + then: + required: + - temperature-mode + else: + not: + required: + - temperature-mode + +required: + - compatible + - reg + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + nct7802@28 { + compatible = "nuvoton,nct7802"; + reg = <0x28>; + + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { /* LTD */ + reg = <0>; + }; + + channel@1 { /* RTD1 */ + reg = <1>; + sensor-type = "voltage"; + }; + + channel@2 { /* RTD2 */ + reg = <2>; + sensor-type = "temperature"; + temperature-mode = "thermal-diode"; + }; + + channel@3 { /* RTD3 */ + reg = <3>; + sensor-type = "temperature"; + }; + }; + }; diff --git a/dts/Bindings/hwmon/nxp,mc34vr500.yaml b/dts/Bindings/hwmon/nxp,mc34vr500.yaml new file mode 100644 index 0000000000..48d654e521 --- /dev/null +++ b/dts/Bindings/hwmon/nxp,mc34vr500.yaml @@ -0,0 +1,36 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/nxp,mc34vr500.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP MC34VR500 hwmon sensor + +maintainers: + - Mario Kicherer <dev@kicherer.org> + +properties: + compatible: + enum: + - nxp,mc34vr500 + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@8 { + compatible = "nxp,mc34vr500"; + reg = <0x08>; + }; + }; diff --git a/dts/Bindings/hwmon/pmbus/infineon,tda38640.yaml b/dts/Bindings/hwmon/pmbus/infineon,tda38640.yaml new file mode 100644 index 0000000000..ded1c11576 --- /dev/null +++ b/dts/Bindings/hwmon/pmbus/infineon,tda38640.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/hwmon/pmbus/infineon,tda38640.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Infineon TDA38640 Synchronous Buck Regulator with SVID and I2C + +maintainers: + - Naresh Solanki <naresh.solanki@9elements.com> + +description: | + The Infineon TDA38640 is a 40A Single-voltage Synchronous Buck + Regulator with SVID and I2C designed for Industrial use. + + Datasheet: https://www.infineon.com/dgdl/Infineon-TDA38640-0000-DataSheet-v02_04-EN.pdf?fileId=8ac78c8c80027ecd018042f2337f00c9 + +properties: + compatible: + enum: + - infineon,tda38640 + + reg: + maxItems: 1 + + infineon,en-pin-fixed-level: + description: + Indicates that the chip EN pin is at fixed level or left + unconnected(has internal pull-down). + type: boolean + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + tda38640@40 { + compatible = "infineon,tda38640"; + reg = <0x40>; + }; + }; diff --git a/dts/Bindings/hwmon/pmbus/ti,lm25066.yaml b/dts/Bindings/hwmon/pmbus/ti,lm25066.yaml new file mode 100644 index 0000000000..da8292bc32 --- /dev/null +++ b/dts/Bindings/hwmon/pmbus/ti,lm25066.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/hwmon/pmbus/ti,lm25066.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: National Semiconductor/Texas Instruments LM250x6/LM506x power-management ICs + +maintainers: + - Zev Weiss <zev@bewilderbeest.net> + +description: | + The LM25066 family of power-management ICs (a.k.a. hot-swap + controllers or eFuses in various contexts) are PMBus devices that + offer temperature, current, voltage, and power monitoring. + + Datasheet: https://www.ti.com/lit/ds/symlink/lm25066.pdf + +properties: + compatible: + enum: + - ti,lm25056 + - ti,lm25066 + - ti,lm5064 + - ti,lm5066 + - ti,lm5066i + + reg: + maxItems: 1 + + shunt-resistor-micro-ohms: + description: + Shunt (sense) resistor value in micro-Ohms + default: 1000 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@40 { + compatible = "ti,lm25066"; + reg = <0x40>; + shunt-resistor-micro-ohms = <675>; + }; + }; diff --git a/dts/Bindings/hwmon/pwm-fan.txt b/dts/Bindings/hwmon/pwm-fan.txt index 4509e68862..48886f0ce4 100644 --- a/dts/Bindings/hwmon/pwm-fan.txt +++ b/dts/Bindings/hwmon/pwm-fan.txt @@ -1,67 +1 @@ -Bindings for a fan connected to the PWM lines - -Required properties: -- compatible : "pwm-fan" -- pwms : the PWM that is used to control the PWM fan -- cooling-levels : PWM duty cycle values in a range from 0 to 255 - which correspond to thermal cooling states - -Optional properties: -- fan-supply : phandle to the regulator that provides power to the fan -- interrupts : This contains an interrupt specifier for each fan - tachometer output connected to an interrupt source. - The output signal must generate a defined number of - interrupts per fan revolution, which require that - it must be self resetting edge interrupts. See - interrupt-controller/interrupts.txt for the format. -- pulses-per-revolution : define the number of pulses per fan revolution for - each tachometer input as an integer (default is 2 - interrupts per revolution). The value must be - greater than zero. - -Example: - fan0: pwm-fan { - compatible = "pwm-fan"; - #cooling-cells = <2>; - pwms = <&pwm 0 10000 0>; - cooling-levels = <0 102 170 230>; - }; - - thermal-zones { - cpu_thermal: cpu-thermal { - thermal-sensors = <&tmu 0>; - polling-delay-passive = <0>; - polling-delay = <0>; - trips { - cpu_alert1: cpu-alert1 { - temperature = <100000>; /* millicelsius */ - hysteresis = <2000>; /* millicelsius */ - type = "passive"; - }; - }; - cooling-maps { - map0 { - trip = <&cpu_alert1>; - cooling-device = <&fan0 0 1>; - }; - }; - }; - -Example 2: - fan0: pwm-fan { - compatible = "pwm-fan"; - pwms = <&pwm 0 40000 0>; - fan-supply = <®_fan>; - interrupt-parent = <&gpio5>; - interrupts = <1 IRQ_TYPE_EDGE_FALLING>; - pulses-per-revolution = <2>; - }; - -Example 3: - fan0: pwm-fan { - compatible = "pwm-fan"; - pwms = <&pwm1 0 25000 0>; - interrupts-extended = <&gpio1 1 IRQ_TYPE_EDGE_FALLING>, - <&gpio2 5 IRQ_TYPE_EDGE_FALLING>; - pulses-per-revolution = <2>, <1>; - }; +This file has moved to pwm-fan.yaml. diff --git a/dts/Bindings/hwmon/pwm-fan.yaml b/dts/Bindings/hwmon/pwm-fan.yaml new file mode 100644 index 0000000000..4e5abf7580 --- /dev/null +++ b/dts/Bindings/hwmon/pwm-fan.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/pwm-fan.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Fan connected to PWM lines + +maintainers: + - Jean Delvare <jdelvare@suse.com> + - Guenter Roeck <linux@roeck-us.net> + +properties: + compatible: + const: pwm-fan + + cooling-levels: + description: PWM duty cycle values corresponding to thermal cooling states. + $ref: /schemas/types.yaml#/definitions/uint32-array + items: + maximum: 255 + + fan-supply: + description: Phandle to the regulator that provides power to the fan. + + interrupts: + description: + This contains an interrupt specifier for each fan tachometer output + connected to an interrupt source. The output signal must generate a + defined number of interrupts per fan revolution, which require that + it must be self resetting edge interrupts. + maxItems: 1 + + pulses-per-revolution: + description: + Define the number of pulses per fan revolution for each tachometer + input as an integer. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 4 + default: 2 + + pwms: + description: The PWM that is used to control the fan. + maxItems: 1 + + "#cooling-cells": true + +required: + - compatible + - pwms + +additionalProperties: false + +examples: + - | + pwm-fan { + compatible = "pwm-fan"; + cooling-levels = <0 102 170 230>; + pwms = <&pwm 0 10000 0>; + #cooling-cells = <2>; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + thermal-sensors = <&tmu 0>; + polling-delay-passive = <0>; + polling-delay = <0>; + + trips { + cpu_alert1: cpu-alert1 { + temperature = <100000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert1>; + cooling-device = <&fan0 0 1>; + }; + }; + }; + }; + + - | + #include <dt-bindings/interrupt-controller/irq.h> + + pwm-fan { + compatible = "pwm-fan"; + pwms = <&pwm 0 40000 0>; + fan-supply = <®_fan>; + interrupt-parent = <&gpio5>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + pulses-per-revolution = <2>; + }; diff --git a/dts/Bindings/hwmon/sensirion,sht15.yaml b/dts/Bindings/hwmon/sensirion,sht15.yaml new file mode 100644 index 0000000000..14ac783c9a --- /dev/null +++ b/dts/Bindings/hwmon/sensirion,sht15.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/sensirion,sht15.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sensirion SHT15 humidity and temperature sensor + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + const: sensirion,sht15 + + clk-gpios: + maxItems: 1 + + data-gpios: + maxItems: 1 + + vcc-supply: + description: regulator that drives the VCC pin + +required: + - compatible + - clk-gpios + - data-gpios + - vcc-supply + +additionalProperties: false + +examples: + - | + sensor { + compatible = "sensirion,sht15"; + clk-gpios = <&gpio4 12 0>; + data-gpios = <&gpio4 13 0>; + vcc-supply = <®_sht15>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor>; + }; diff --git a/dts/Bindings/hwmon/sensirion,shtc1.yaml b/dts/Bindings/hwmon/sensirion,shtc1.yaml index 7d49478d96..3d14d5fc96 100644 --- a/dts/Bindings/hwmon/sensirion,shtc1.yaml +++ b/dts/Bindings/hwmon/sensirion,shtc1.yaml @@ -10,10 +10,10 @@ maintainers: - Christopher Ruehl chris.ruehl@gtsys.com.hk description: | - The SHTC1, SHTW1 and SHTC3 are digital humidity and temperature sensor + The SHTC1, SHTW1 and SHTC3 are digital humidity and temperature sensors designed especially for battery-driven high-volume consumer electronics applications. - For further information refere to Documentation/hwmon/shtc1.rst + For further information refer to Documentation/hwmon/shtc1.rst This binding document describes the binding for the hardware monitor portion of the driver. @@ -31,13 +31,13 @@ properties: sensirion,blocking-io: $ref: /schemas/types.yaml#/definitions/flag description: - If set, the driver hold the i2c bus until measurement is finished. + If set, the driver holds the i2c bus until the measurement is finished. sensirion,low-precision: $ref: /schemas/types.yaml#/definitions/flag description: - If set, the sensor aquire data with low precision (not recommended). - The driver aquire data with high precision by default. + If set, the sensor acquires data with low precision (not recommended). + The driver acquires data with high precision by default. required: - compatible diff --git a/dts/Bindings/hwmon/sht15.txt b/dts/Bindings/hwmon/sht15.txt deleted file mode 100644 index 6a80277cc4..0000000000 --- a/dts/Bindings/hwmon/sht15.txt +++ /dev/null @@ -1,19 +0,0 @@ -Sensirion SHT15 Humidity and Temperature Sensor - -Required properties: - - - "compatible": must be "sensirion,sht15". - - "data-gpios": GPIO connected to the data line. - - "clk-gpios": GPIO connected to the clock line. - - "vcc-supply": regulator that drives the VCC pin. - -Example: - - sensor { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_sensor>; - compatible = "sensirion,sht15"; - clk-gpios = <&gpio4 12 0>; - data-gpios = <&gpio4 13 0>; - vcc-supply = <®_sht15>; - }; diff --git a/dts/Bindings/hwmon/starfive,jh71x0-temp.yaml b/dts/Bindings/hwmon/starfive,jh71x0-temp.yaml new file mode 100644 index 0000000000..733cba7801 --- /dev/null +++ b/dts/Bindings/hwmon/starfive,jh71x0-temp.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/starfive,jh71x0-temp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: StarFive JH71x0 Temperature Sensor + +maintainers: + - Emil Renner Berthing <kernel@esmil.dk> + +description: | + StarFive Technology Co. JH71x0 embedded temperature sensor + +properties: + compatible: + enum: + - starfive,jh7100-temp + - starfive,jh7110-temp + + reg: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 2 + + clock-names: + items: + - const: sense + - const: bus + + '#thermal-sensor-cells': + const: 0 + + resets: + minItems: 2 + maxItems: 2 + + reset-names: + items: + - const: sense + - const: bus + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/starfive-jh7100.h> + #include <dt-bindings/reset/starfive-jh7100.h> + + temperature-sensor@124a0000 { + compatible = "starfive,jh7100-temp"; + reg = <0x124a0000 0x10000>; + clocks = <&clkgen JH7100_CLK_TEMP_SENSE>, + <&clkgen JH7100_CLK_TEMP_APB>; + clock-names = "sense", "bus"; + #thermal-sensor-cells = <0>; + resets = <&rstgen JH7100_RSTN_TEMP_SENSE>, + <&rstgen JH7100_RSTN_TEMP_APB>; + reset-names = "sense", "bus"; + }; diff --git a/dts/Bindings/hwmon/ti,ads7828.yaml b/dts/Bindings/hwmon/ti,ads7828.yaml index 33ee575bb0..926be9a290 100644 --- a/dts/Bindings/hwmon/ti,ads7828.yaml +++ b/dts/Bindings/hwmon/ti,ads7828.yaml @@ -49,7 +49,7 @@ examples: #size-cells = <0>; adc@48 { - comatible = "ti,ads7828"; + compatible = "ti,ads7828"; reg = <0x48>; vref-supply = <&vref>; ti,differential-input; diff --git a/dts/Bindings/hwmon/ti,ina2xx.yaml b/dts/Bindings/hwmon/ti,ina2xx.yaml index 6f0443322a..378d1f6aee 100644 --- a/dts/Bindings/hwmon/ti,ina2xx.yaml +++ b/dts/Bindings/hwmon/ti,ina2xx.yaml @@ -26,6 +26,8 @@ properties: - ti,ina226 - ti,ina230 - ti,ina231 + - ti,ina237 + - ti,ina238 reg: maxItems: 1 @@ -35,6 +37,31 @@ properties: Shunt resistor value in micro-Ohm. $ref: /schemas/types.yaml#/definitions/uint32 + ti,shunt-gain: + description: | + Programmable gain divisor for the shunt voltage accuracy and range. This + property only applies to devices that have configurable PGA/ADCRANGE. The + gain value is used configure the gain and to convert the shunt voltage, + current and power register values when reading measurements from the + device. + + For devices that have a configurable PGA (e.g. INA209, INA219, INA220), + the gain value maps directly with the PG bits of the config register. + + For devices that have ADCRANGE configuration (e.g. INA238) a shunt-gain + value of 1 maps to ADCRANGE=1 where no gain divisor is applied to the + shunt voltage, and a value of 4 maps to ADCRANGE=0 such that a wider + voltage range is used. + + The default value is device dependent, and is defined by the reset value + of PGA/ADCRANGE in the respective configuration registers. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 4, 8] + + vs-supply: + description: phandle to the regulator that provides the VS supply typically + in range from 2.7 V to 5.5 V. + required: - compatible - reg @@ -51,5 +78,6 @@ examples: compatible = "ti,ina220"; reg = <0x44>; shunt-resistor = <1000>; + vs-supply = <&vdd_3v0>; }; }; diff --git a/dts/Bindings/hwmon/ti,ina3221.yaml b/dts/Bindings/hwmon/ti,ina3221.yaml new file mode 100644 index 0000000000..5f10f1207d --- /dev/null +++ b/dts/Bindings/hwmon/ti,ina3221.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/ti,ina3221.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments INA3221 Current and Voltage Monitor + +maintainers: + - Jean Delvare <jdelvare@suse.com> + - Guenter Roeck <linux@roeck-us.net> + +properties: + compatible: + const: ti,ina3221 + + reg: + maxItems: 1 + + ti,single-shot: + description: | + This chip has two power modes: single-shot (chip takes one measurement + and then shuts itself down) and continuous (chip takes continuous + measurements). The continuous mode is more reliable and suitable for + hardware monitor type device, but the single-shot mode is more power- + friendly and useful for battery-powered device which cares power + consumptions while still needs some measurements occasionally. + + If this property is present, the single-shot mode will be used, instead + of the default continuous one for monitoring. + $ref: /schemas/types.yaml#/definitions/flag + + "#address-cells": + description: Required only if a child node is present. + const: 1 + + "#size-cells": + description: Required only if a child node is present. + const: 0 + +patternProperties: + "^input@[0-2]$": + description: The node contains optional child nodes for three channels. + Each child node describes the information of input source. Input channels + default to enabled in the chip. Unless channels are explicitly disabled + in device-tree, input channels will be enabled. + type: object + additionalProperties: false + properties: + reg: + description: Must be 0, 1 and 2, corresponding to the IN1, IN2 or IN3 + ports of the INA3221, respectively. + enum: [ 0, 1, 2 ] + + label: + description: name of the input source + + shunt-resistor-micro-ohms: + description: shunt resistor value in micro-Ohm + + ti,summation-disable: + description: | + The INA3221 has a critical alert pin that can be controlled by the + summation control function. This function adds the single + shunt-voltage conversions for the desired channels in order to + compare the combined sum to the programmed limit. The Shunt-Voltage + Sum Limit register contains the programmed value that is compared + to the value in the Shunt-Voltage Sum register in order to + determine if the total summed limit is exceeded. If the + shunt-voltage sum limit value is exceeded, the critical alert pin + is asserted. + + For the summation limit to have a meaningful value, it is necessary + to use the same shunt-resistor value on all enabled channels. If + this is not the case or if a channel should not be used for + triggering the critical alert pin, then this property can be used + exclude specific channels from the summation control function. + type: boolean + + required: + - reg + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + power-sensor@40 { + compatible = "ti,ina3221"; + reg = <0x40>; + #address-cells = <1>; + #size-cells = <0>; + + input@0 { + reg = <0x0>; + /* + * Input channels are enabled by default in the device and so + * to disable, must be explicitly disabled in device-tree. + */ + status = "disabled"; + }; + + input@1 { + reg = <0x1>; + shunt-resistor-micro-ohms = <5000>; + }; + + input@2 { + reg = <0x2>; + label = "VDD_5V"; + shunt-resistor-micro-ohms = <5000>; + }; + }; + }; diff --git a/dts/Bindings/hwmon/ti,tmp102.yaml b/dts/Bindings/hwmon/ti,tmp102.yaml new file mode 100644 index 0000000000..7e5b62a021 --- /dev/null +++ b/dts/Bindings/hwmon/ti,tmp102.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/ti,tmp102.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TMP102 temperature sensor + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + enum: + - ti,tmp102 + + interrupts: + maxItems: 1 + + reg: + maxItems: 1 + + "#thermal-sensor-cells": + const: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@48 { + compatible = "ti,tmp102"; + reg = <0x48>; + interrupt-parent = <&gpio7>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + #thermal-sensor-cells = <1>; + }; + }; diff --git a/dts/Bindings/hwmon/ti,tmp108.yaml b/dts/Bindings/hwmon/ti,tmp108.yaml new file mode 100644 index 0000000000..8b5307c875 --- /dev/null +++ b/dts/Bindings/hwmon/ti,tmp108.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/ti,tmp108.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TMP108 temperature sensor + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + enum: + - ti,tmp108 + + interrupts: + items: + - description: alert interrupt + + reg: + maxItems: 1 + + "#thermal-sensor-cells": + const: 0 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@48 { + compatible = "ti,tmp108"; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&tmp_alrt>; + #thermal-sensor-cells = <0>; + }; + }; diff --git a/dts/Bindings/hwmon/ti,tmp401.yaml b/dts/Bindings/hwmon/ti,tmp401.yaml new file mode 100644 index 0000000000..0e8ddf0ad7 --- /dev/null +++ b/dts/Bindings/hwmon/ti,tmp401.yaml @@ -0,0 +1,104 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/ti,tmp401.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TMP401, TPM411 and TMP43x temperature sensor + +maintainers: + - Guenter Roeck <linux@roeck-us.net> + +description: | + ±1°C Remote and Local temperature sensor + + Datasheets: + https://www.ti.com/lit/ds/symlink/tmp401.pdf + https://www.ti.com/lit/ds/symlink/tmp411.pdf + https://www.ti.com/lit/ds/symlink/tmp431.pdf + https://www.ti.com/lit/ds/symlink/tmp435.pdf + +properties: + compatible: + enum: + - ti,tmp401 + - ti,tmp411 + - ti,tmp431 + - ti,tmp432 + - ti,tmp435 + + reg: + maxItems: 1 + + ti,extended-range-enable: + description: + When set, this sensor measures over extended temperature range. + type: boolean + + ti,n-factor: + description: + value to be used for converting remote channel measurements to + temperature. + $ref: /schemas/types.yaml#/definitions/int32 + minimum: -128 + maximum: 127 + + ti,beta-compensation: + description: + value to select beta correction range. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + +allOf: + - if: + properties: + compatible: + contains: + enum: + - ti,tmp401 + then: + properties: + ti,n-factor: false + + - if: + properties: + compatible: + contains: + enum: + - ti,tmp401 + - ti,tmp411 + then: + properties: + ti,beta-compensation: false + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@4c { + compatible = "ti,tmp401"; + reg = <0x4c>; + }; + }; + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@4c { + compatible = "ti,tmp431"; + reg = <0x4c>; + ti,extended-range-enable; + ti,n-factor = <0x3b>; + ti,beta-compensation = <0x7>; + }; + }; diff --git a/dts/Bindings/hwmon/ti,tmp421.yaml b/dts/Bindings/hwmon/ti,tmp421.yaml new file mode 100644 index 0000000000..a6f1fa75a6 --- /dev/null +++ b/dts/Bindings/hwmon/ti,tmp421.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/ti,tmp421.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TMP42x/TMP44x temperature sensor + +maintainers: + - Guenter Roeck <linux@roeck-us.net> + +description: | + ±1°C Remote and Local temperature sensor + https://www.ti.com/lit/ds/symlink/tmp422.pdf + +properties: + compatible: + enum: + - ti,tmp421 + - ti,tmp422 + - ti,tmp423 + - ti,tmp441 + - ti,tmp442 + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +required: + - compatible + - reg + +additionalProperties: false + +patternProperties: + "^channel@([0-3])$": + type: object + description: | + Represents channels of the device and their specific configuration. + + properties: + reg: + description: | + The channel number. 0 is local channel, 1-3 are remote channels + items: + minimum: 0 + maximum: 3 + + label: + description: | + A descriptive name for this channel, like "ambient" or "psu". + + ti,n-factor: + description: | + The value (two's complement) to be programmed in the channel specific N correction register. + For remote channels only. + $ref: /schemas/types.yaml#/definitions/int32 + minimum: -128 + maximum: 127 + + required: + - reg + + additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@4c { + compatible = "ti,tmp422"; + reg = <0x4c>; + }; + }; + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@4c { + compatible = "ti,tmp422"; + reg = <0x4c>; + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0x0>; + ti,n-factor = <0x1>; + label = "local"; + }; + + channel@1 { + reg = <0x1>; + ti,n-factor = <0x0>; + label = "somelabel"; + }; + + channel@2 { + reg = <0x2>; + status = "disabled"; + }; + }; + }; diff --git a/dts/Bindings/hwmon/ti,tmp464.yaml b/dts/Bindings/hwmon/ti,tmp464.yaml new file mode 100644 index 0000000000..f9c00cbb28 --- /dev/null +++ b/dts/Bindings/hwmon/ti,tmp464.yaml @@ -0,0 +1,113 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/ti,tmp464.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TMP464 and TMP468 temperature sensors + +maintainers: + - Guenter Roeck <linux@roeck-us.net> + +description: | + ±0.0625°C Remote and Local temperature sensor + https://www.ti.com/lit/ds/symlink/tmp464.pdf + https://www.ti.com/lit/ds/symlink/tmp468.pdf + +properties: + compatible: + enum: + - ti,tmp464 + - ti,tmp468 + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +required: + - compatible + - reg + +additionalProperties: false + +patternProperties: + "^channel@([0-8])$": + type: object + description: | + Represents channels of the device and their specific configuration. + + properties: + reg: + description: | + The channel number. 0 is local channel, 1-8 are remote channels. + items: + minimum: 0 + maximum: 8 + + label: + description: | + A descriptive name for this channel, like "ambient" or "psu". + + ti,n-factor: + description: | + The value (two's complement) to be programmed in the channel specific N correction register. + For remote channels only. + $ref: /schemas/types.yaml#/definitions/int32 + minimum: -128 + maximum: 127 + + required: + - reg + + additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@4b { + compatible = "ti,tmp464"; + reg = <0x4b>; + }; + }; + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sensor@4b { + compatible = "ti,tmp464"; + reg = <0x4b>; + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0x0>; + label = "local"; + }; + + channel@1 { + reg = <0x1>; + ti,n-factor = <(-10)>; + label = "external"; + }; + + channel@2 { + reg = <0x2>; + ti,n-factor = <0x10>; + label = "somelabel"; + }; + + channel@3 { + reg = <0x3>; + status = "disabled"; + }; + }; + }; diff --git a/dts/Bindings/hwmon/ti,tmp513.yaml b/dts/Bindings/hwmon/ti,tmp513.yaml index 1502b22c77..cdd1489e0c 100644 --- a/dts/Bindings/hwmon/ti,tmp513.yaml +++ b/dts/Bindings/hwmon/ti,tmp513.yaml @@ -33,7 +33,7 @@ properties: shunt-resistor-micro-ohms: description: | - If 0, the calibration process will be skiped and the current and power + If 0, the calibration process will be skipped and the current and power measurement engine will not work. Temperature and voltage measurement will continue to work. The shunt value also need to respect: rshunt <= pga-gain * 40 * 1000 * 1000. @@ -77,15 +77,15 @@ additionalProperties: false examples: - | i2c { - #address-cells = <1>; - #size-cells = <0>; - - tmp513@5c { - compatible = "ti,tmp513"; - reg = <0x5C>; - shunt-resistor-micro-ohms = <330000>; - ti,bus-range-microvolt = <32000000>; - ti,pga-gain = <8>; - ti,nfactor = <0x1 0xF3 0x00>; - }; + #address-cells = <1>; + #size-cells = <0>; + + tmp513@5c { + compatible = "ti,tmp513"; + reg = <0x5c>; + shunt-resistor-micro-ohms = <330000>; + ti,bus-range-microvolt = <32000000>; + ti,pga-gain = <8>; + ti,nfactor = <0x1 0xf3 0x00>; + }; }; diff --git a/dts/Bindings/hwmon/ti,tps23861.yaml b/dts/Bindings/hwmon/ti,tps23861.yaml index 3bc8e73dfb..ebc8d466c1 100644 --- a/dts/Bindings/hwmon/ti,tps23861.yaml +++ b/dts/Bindings/hwmon/ti,tps23861.yaml @@ -26,7 +26,7 @@ properties: maxItems: 1 shunt-resistor-micro-ohms: - description: The value of curent sense resistor in microohms. + description: The value of current sense resistor in microohms. default: 255000 minimum: 250000 maximum: 255000 @@ -40,12 +40,12 @@ additionalProperties: false examples: - | i2c { - #address-cells = <1>; - #size-cells = <0>; - - tps23861@30 { - compatible = "ti,tps23861"; - reg = <0x30>; - shunt-resistor-micro-ohms = <255000>; - }; + #address-cells = <1>; + #size-cells = <0>; + + tps23861@30 { + compatible = "ti,tps23861"; + reg = <0x30>; + shunt-resistor-micro-ohms = <255000>; + }; }; diff --git a/dts/Bindings/hwmon/tmp108.txt b/dts/Bindings/hwmon/tmp108.txt deleted file mode 100644 index 54d4beed4e..0000000000 --- a/dts/Bindings/hwmon/tmp108.txt +++ /dev/null @@ -1,18 +0,0 @@ -TMP108 temperature sensor -------------------------- - -This device supports I2C only. - -Requires node properties: -- compatible : "ti,tmp108" -- reg : the I2C address of the device. This is 0x48, 0x49, 0x4a, or 0x4b. - -Optional properties: -- interrupts: Reference to the TMP108 alert interrupt. -- #thermal-sensor-cells: should be set to 0. - -Example: - tmp108@48 { - compatible = "ti,tmp108"; - reg = <0x48>; - }; diff --git a/dts/Bindings/hwmon/vexpress.txt b/dts/Bindings/hwmon/vexpress.txt index 9c27ed694b..4a4df4ffc4 100644 --- a/dts/Bindings/hwmon/vexpress.txt +++ b/dts/Bindings/hwmon/vexpress.txt @@ -9,7 +9,7 @@ Requires node properties: "arm,vexpress-power" "arm,vexpress-energy" - "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg - (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt + (see Documentation/devicetree/bindings/arm/vexpress-config.yaml for more details) Optional node properties: diff --git a/dts/Bindings/hwmon/winbond,w83781d.yaml b/dts/Bindings/hwmon/winbond,w83781d.yaml new file mode 100644 index 0000000000..31ce77a4b0 --- /dev/null +++ b/dts/Bindings/hwmon/winbond,w83781d.yaml @@ -0,0 +1,41 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/hwmon/winbond,w83781d.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Winbond W83781 and compatible hardware monitor IC + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +properties: + compatible: + enum: + - winbond,w83781d + - winbond,w83781g + - winbond,w83782d + - winbond,w83783s + - asus,as99127f + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + temperature-sensor@28 { + compatible = "winbond,w83781d"; + reg = <0x28>; + }; + }; |