diff options
Diffstat (limited to 'dts/Bindings/iio/adc/qcom,pm8xxx-xoadc.txt')
| -rw-r--r-- | dts/Bindings/iio/adc/qcom,pm8xxx-xoadc.txt | 157 |
1 files changed, 0 insertions, 157 deletions
diff --git a/dts/Bindings/iio/adc/qcom,pm8xxx-xoadc.txt b/dts/Bindings/iio/adc/qcom,pm8xxx-xoadc.txt deleted file mode 100644 index 3ae0612778..0000000000 --- a/dts/Bindings/iio/adc/qcom,pm8xxx-xoadc.txt +++ /dev/null @@ -1,157 +0,0 @@ -Qualcomm's PM8xxx voltage XOADC - -The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Crystal -oscillator ADC) encompassing PM8018, PM8038, PM8058 and PM8921. - -Required properties: - -- compatible: should be one of: - "qcom,pm8018-adc" - "qcom,pm8038-adc" - "qcom,pm8058-adc" - "qcom,pm8921-adc" - -- reg: should contain the ADC base address in the PMIC, typically - 0x197. - -- xoadc-ref-supply: should reference a regulator that can supply - a reference voltage on demand. The reference voltage may vary - with PMIC variant but is typically something like 2.2 or 1.8V. - -The following required properties are standard for IO channels, see -iio-bindings.txt for more details, but notice that this particular -ADC has a special addressing scheme that require two cells for -identifying each ADC channel: - -- #address-cells: should be set to <2>, the first cell is the - prescaler (on PM8058) or premux (on PM8921) with two valid bits - so legal values are 0x00, 0x01 or 0x02. The second cell - is the main analog mux setting (0x00..0x0f). The combination - of prescaler/premux and analog mux uniquely addresses a hardware - channel on all systems. - -- #size-cells: should be set to <0> - -- #io-channel-cells: should be set to <2>, again the cells are - precaler or premux followed by the analog muxing line. - -- interrupts: should refer to the parent PMIC interrupt controller - and reference the proper ADC interrupt. - -Required subnodes: - -The ADC channels are configured as subnodes of the ADC. - -Since some of them are used for calibrating the ADC, these nodes are -compulsory: - -adc-channel@c { - reg = <0x00 0x0c>; -}; - -adc-channel@d { - reg = <0x00 0x0d>; -}; - -adc-channel@f { - reg = <0x00 0x0f>; -}; - -These three nodes are used for absolute and ratiometric calibration -and only need to have these reg values: they are by hardware definition -1:1 ratio converters that sample 625, 1250 and 0 milliV and create -an interpolation calibration for all other ADCs. - -Optional subnodes: any channels other than channels [0x00 0x0c], -[0x00 0x0d] and [0x00 0x0f] are optional. - -Required channel node properties: - -- reg: should contain the hardware channel number in the range - 0 .. 0xff (8 bits). - -Optional channel node properties: - -- qcom,decimation: - Value type: <u32> - Definition: This parameter is used to decrease the ADC sampling rate. - Quicker measurements can be made by reducing the decimation ratio. - Valid values are 512, 1024, 2048, 4096. - If the property is not found, a default value of 512 will be used. - -- qcom,ratiometric: - Value type: <u32> - Definition: Channel calibration type. If this property is specified - VADC will use a special voltage references for channel - calibration. The available references are specified in the - as a u32 value setting (see below) and it is compulsory - to also specify this reference if ratiometric calibration - is selected. - - If the property is not found, the channel will be - calibrated with the 0.625V and 1.25V reference channels, also - known as an absolute calibration. - The reference voltage pairs when using ratiometric calibration: - 0 = XO_IN/XOADC_GND - 1 = PMIC_IN/XOADC_GND - 2 = PMIC_IN/BMS_CSP - 3 (invalid) - 4 = XOADC_GND/XOADC_GND - 5 = XOADC_VREF/XOADC_GND - -Example: - -xoadc: xoadc@197 { - compatible = "qcom,pm8058-adc"; - reg = <0x197>; - interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>; - #address-cells = <2>; - #size-cells = <0>; - #io-channel-cells = <2>; - - vcoin: adc-channel@0 { - reg = <0x00 0x00>; - }; - vbat: adc-channel@1 { - reg = <0x00 0x01>; - }; - dcin: adc-channel@2 { - reg = <0x00 0x02>; - }; - ichg: adc-channel@3 { - reg = <0x00 0x03>; - }; - vph_pwr: adc-channel@4 { - reg = <0x00 0x04>; - }; - usb_vbus: adc-channel@a { - reg = <0x00 0x0a>; - }; - die_temp: adc-channel@b { - reg = <0x00 0x0b>; - }; - ref_625mv: adc-channel@c { - reg = <0x00 0x0c>; - }; - ref_1250mv: adc-channel@d { - reg = <0x00 0x0d>; - }; - ref_325mv: adc-channel@e { - reg = <0x00 0x0e>; - }; - ref_muxoff: adc-channel@f { - reg = <0x00 0x0f>; - }; -}; - -/* IIO client node */ -iio-hwmon { - compatible = "iio-hwmon"; - io-channels = <&xoadc 0x00 0x01>, /* Battery */ - <&xoadc 0x00 0x02>, /* DC in (charger) */ - <&xoadc 0x00 0x04>, /* VPH the main system voltage */ - <&xoadc 0x00 0x0b>, /* Die temperature */ - <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */ - <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */ - <&xoadc 0x00 0x0e>; /* Reference voltage 0.325V */ -}; |