diff options
Diffstat (limited to 'dts/Bindings/iio/adc/renesas,gyroadc.txt')
| -rw-r--r-- | dts/Bindings/iio/adc/renesas,gyroadc.txt | 98 |
1 files changed, 0 insertions, 98 deletions
diff --git a/dts/Bindings/iio/adc/renesas,gyroadc.txt b/dts/Bindings/iio/adc/renesas,gyroadc.txt deleted file mode 100644 index df5b9f2ad8..0000000000 --- a/dts/Bindings/iio/adc/renesas,gyroadc.txt +++ /dev/null @@ -1,98 +0,0 @@ -* Renesas R-Car GyroADC device driver - -The GyroADC block is a reduced SPI block with up to 8 chipselect lines, -which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs -are sampled by the GyroADC block in a round-robin fashion and the result -presented in the GyroADC registers. - -Required properties: -- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc". - The <soc-specific> should be one of: - renesas,r8a7791-gyroadc - for the GyroADC block present - in r8a7791 SoC - renesas,r8a7792-gyroadc - for the GyroADC with interrupt - block present in r8a7792 SoC -- reg: Address and length of the register set for the device -- clocks: References to all the clocks specified in the clock-names - property as specified in - Documentation/devicetree/bindings/clock/clock-bindings.txt. -- clock-names: Shall contain "fck". The "fck" is the GyroADC block clock. -- power-domains: Must contain a reference to the PM domain, if available. -- #address-cells: Should be <1> (setting for the subnodes) for all ADCs - except for "fujitsu,mb88101a". Should be <0> (setting for - only subnode) for "fujitsu,mb88101a". -- #size-cells: Should be <0> (setting for the subnodes) - -Sub-nodes: -You must define subnode(s) which select the connected ADC type and reference -voltage for the GyroADC channels. - -Required properties for subnodes: -- compatible: Should be either of: - "fujitsu,mb88101a" - - Fujitsu MB88101A compatible mode, - 12bit sampling, up to 4 channels can be sampled in - round-robin fashion. One Fujitsu chip supplies four - GyroADC channels with data as it contains four ADCs - on the chip and thus for 4-channel operation, single - MB88101A is required. The Cx chipselect lines of the - MB88101A connect directly to two CHS lines of the - GyroADC, no demuxer is required. The data out line - of each MB88101A connects to a shared input pin of - the GyroADC. - "ti,adcs7476" or "ti,adc121" or "adi,ad7476" - - TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, - 15bit sampling, up to 8 channels can be sampled in - round-robin fashion. One TI/ADI chip supplies single - ADC channel with data, thus for 8-channel operation, - 8 chips are required. A 3:8 chipselect demuxer is - required to connect the nCS line of the TI/ADI chips - to the GyroADC, while MISO line of each TI/ADI ADC - connects to a shared input pin of the GyroADC. - "maxim,max1162" or "maxim,max11100" - - Maxim MAX1162 / Maxim MAX11100 compatible mode, - 16bit sampling, up to 8 channels can be sampled in - round-robin fashion. One Maxim chip supplies single - ADC channel with data, thus for 8-channel operation, - 8 chips are required. A 3:8 chipselect demuxer is - required to connect the nCS line of the MAX chips - to the GyroADC, while MISO line of each Maxim ADC - connects to a shared input pin of the GyroADC. -- reg: Should be the number of the analog input. Should be present - for all ADCs except "fujitsu,mb88101a". -- vref-supply: Reference to the channel reference voltage regulator. - -Example: - vref_max1162: regulator-vref-max1162 { - compatible = "regulator-fixed"; - - regulator-name = "MAX1162 Vref"; - regulator-min-microvolt = <4096000>; - regulator-max-microvolt = <4096000>; - }; - - adc@e6e54000 { - compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; - reg = <0 0xe6e54000 0 64>; - clocks = <&mstp9_clks R8A7791_CLK_GYROADC>; - clock-names = "fck"; - power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; - - pinctrl-0 = <&adc_pins>; - pinctrl-names = "default"; - - #address-cells = <1>; - #size-cells = <0>; - - adc@0 { - reg = <0>; - compatible = "maxim,max1162"; - vref-supply = <&vref_max1162>; - }; - - adc@1 { - reg = <1>; - compatible = "maxim,max1162"; - vref-supply = <&vref_max1162>; - }; - }; |