1 files changed, 0 insertions, 86 deletions
diff --git a/dts/Bindings/iio/imu/adi,adis16480.txt b/dts/Bindings/iio/imu/adi,adis16480.txt
deleted file mode 100644
index cd903a1d88..0000000000
--- a/dts/Bindings/iio/imu/adi,adis16480.txt
+++ /dev/null
@@ -1,86 +0,0 @@
-
-Analog Devices ADIS16480 and similar IMUs
-
-Required properties for the ADIS16480:
-
-- compatible: Must be one of
-	* "adi,adis16375"
-	* "adi,adis16480"
-	* "adi,adis16485"
-	* "adi,adis16488"
-	* "adi,adis16490"
-	* "adi,adis16495-1"
-	* "adi,adis16495-2"
-	* "adi,adis16495-3"
-	* "adi,adis16497-1"
-	* "adi,adis16497-2"
-	* "adi,adis16497-3"
-- reg: SPI chip select number for the device
-- spi-max-frequency: Max SPI frequency to use
-	see: Documentation/devicetree/bindings/spi/spi-bus.txt
-- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
-- spi-cpol: See Documentation/devicetree/bindings/spi/spi-bus.txt
-- interrupts: interrupt mapping for IRQ, accepted values are:
-	* IRQF_TRIGGER_RISING
-	* IRQF_TRIGGER_FALLING
-
-Optional properties:
-
-- interrupt-names: Data ready line selection. Valid values are:
-	* DIO1
-	* DIO2
-	* DIO3
-	* DIO4
-	If this field is left empty, DIO1 is assigned as default data ready
-	signal.
-- reset-gpios: must be the device tree identifier of the RESET pin. As the line
-	is active low, it should be marked GPIO_ACTIVE_LOW.
-- clocks: phandle to the external clock. Should be set according to
-	"clock-names".
-	If this field is left empty together with the "clock-names" field, then
-	the internal clock is used.
-- clock-names: The name of the external clock to be used. Valid values are:
-	* sync: In sync mode, the internal clock is disabled and the frequency
-		of the external clock signal establishes therate of data
-		collection and processing. See Fig 14 and 15 in the datasheet.
-		The clock-frequency must be:
-		* 3000 to 4500 Hz for adis1649x devices.
-		* 700 to 2400 Hz for adis1648x devices.
-	* pps: In Pulse Per Second (PPS) Mode, the rate of data collection and
-	       production is equal to the product of the external clock
-	       frequency and the scale factor in the SYNC_SCALE register, see
-	       Table 154 in the datasheet.
-	       The clock-frequency must be:
-	       * 1 to 128 Hz for adis1649x devices.
-	       * This mode is not supported by adis1648x devices.
-	If this field is left empty together with the "clocks" field, then the
-	internal clock is used.
-- adi,ext-clk-pin: The DIOx line to be used as an external clock input.
-	Valid values are:
-	* DIO1
-	* DIO2
-	* DIO3
-	* DIO4
-	Each DIOx pin supports only one function at a time (data ready line
-	selection or external clock input). When a single pin has two
-	two assignments, the enable bit for the lower priority function
-	automatically resets to zero (disabling the lower priority function).
-	Data ready has highest priority.
-	If this field is left empty, DIO2 is assigned as default external clock
-	input pin.
-
-Example:
-
-	imu@0 {
-		compatible = "adi,adis16495-1";
-		reg = <0>;
-		spi-max-frequency = <3200000>;
-		spi-cpol;
-		spi-cpha;
-		interrupts = <25 IRQF_TRIGGER_FALLING>;
-		interrupt-parent = <&gpio>;
-		interrupt-names = "DIO2";
-		clocks = <&adis16495_sync>;
-		clock-names = "sync";
-		adi,ext-clk-pin = "DIO1";
-	};