diff options
Diffstat (limited to 'dts/Bindings/input/touchscreen')
| -rw-r--r-- | dts/Bindings/input/touchscreen/colibri-vf50-ts.txt | 36 | ||||
| -rw-r--r-- | dts/Bindings/input/touchscreen/edt-ft5x06.txt | 8 | ||||
| -rw-r--r-- | dts/Bindings/input/touchscreen/focaltech-ft6236.txt | 35 | ||||
| -rw-r--r-- | dts/Bindings/input/touchscreen/imx6ul_tsc.txt | 36 | ||||
| -rw-r--r-- | dts/Bindings/input/touchscreen/pixcir_i2c_ts.txt | 3 | ||||
| -rw-r--r-- | dts/Bindings/input/touchscreen/tsc2005.txt | 34 | ||||
| -rw-r--r-- | dts/Bindings/input/touchscreen/zforce_ts.txt | 8 |
7 files changed, 147 insertions, 13 deletions
diff --git a/dts/Bindings/input/touchscreen/colibri-vf50-ts.txt b/dts/Bindings/input/touchscreen/colibri-vf50-ts.txt new file mode 100644 index 0000000000..9d9e930f32 --- /dev/null +++ b/dts/Bindings/input/touchscreen/colibri-vf50-ts.txt @@ -0,0 +1,36 @@ +* Toradex Colibri VF50 Touchscreen driver + +Required Properties: +- compatible must be toradex,vf50-touchscreen +- io-channels: adc channels being used by the Colibri VF50 module +- xp-gpios: FET gate driver for input of X+ +- xm-gpios: FET gate driver for input of X- +- yp-gpios: FET gate driver for input of Y+ +- ym-gpios: FET gate driver for input of Y- +- interrupt-parent: phandle for the interrupt controller +- interrupts: pen irq interrupt for touch detection +- pinctrl-names: "idle", "default", "gpios" +- pinctrl-0: pinctrl node for pen/touch detection state pinmux +- pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux +- pinctrl-2: pinctrl node for gpios functioning as FET gate drivers +- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values + +Example: + + touchctrl: vf50_touchctrl { + compatible = "toradex,vf50-touchscreen"; + io-channels = <&adc1 0>,<&adc0 0>, + <&adc0 1>,<&adc1 2>; + xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; + yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "idle","default","gpios"; + pinctrl-0 = <&pinctrl_touchctrl_idle>; + pinctrl-1 = <&pinctrl_touchctrl_default>; + pinctrl-2 = <&pinctrl_touchctrl_gpios>; + vf50-ts-min-pressure = <200>; + status = "disabled"; + }; diff --git a/dts/Bindings/input/touchscreen/edt-ft5x06.txt b/dts/Bindings/input/touchscreen/edt-ft5x06.txt index 76db96704a..f99528da1b 100644 --- a/dts/Bindings/input/touchscreen/edt-ft5x06.txt +++ b/dts/Bindings/input/touchscreen/edt-ft5x06.txt @@ -5,6 +5,7 @@ There are 3 variants of the chip for various touch panel sizes FT5206GE1 2.8" .. 3.8" FT5306DE4 4.3" .. 7" FT5406EE8 7" .. 8.9" +FT5506EEG 7" .. 8.9" The software interface is identical for all those chips, so that currently there is no need for the driver to distinguish between the @@ -17,6 +18,7 @@ Required properties: - compatible: "edt,edt-ft5206" or: "edt,edt-ft5306" or: "edt,edt-ft5406" + or: "edt,edt-ft5506" - reg: I2C slave address of the chip (0x38) - interrupt-parent: a phandle pointing to the interrupt controller @@ -49,7 +51,7 @@ Example: pinctrl-names = "default"; pinctrl-0 = <&edt_ft5x06_pins>; interrupt-parent = <&gpio2>; - interrupts = <5 0>; - reset-gpios = <&gpio2 6 1>; - wake-gpios = <&gpio4 9 0>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; + wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>; }; diff --git a/dts/Bindings/input/touchscreen/focaltech-ft6236.txt b/dts/Bindings/input/touchscreen/focaltech-ft6236.txt new file mode 100644 index 0000000000..777521da3d --- /dev/null +++ b/dts/Bindings/input/touchscreen/focaltech-ft6236.txt @@ -0,0 +1,35 @@ +* FocalTech FT6236 I2C touchscreen controller + +Required properties: + - compatible : "focaltech,ft6236" + - reg : I2C slave address of the chip (0x38) + - interrupt-parent : a phandle pointing to the interrupt controller + serving the interrupt for this chip + - interrupts : interrupt specification for the touch controller + interrupt + - reset-gpios : GPIO specification for the RSTN input + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + +Optional properties: + - touchscreen-fuzz-x : horizontal noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input + device (in pixels) + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y: X and Y axis are swapped (boolean) + Swapping is done after inverting the axis + +Example: + + ft6x06@38 { + compatible = "focaltech,ft6236"; + reg = <0x38>; + interrupt-parent = <&gpio>; + interrupts = <23 2>; + touchscreen-size-x = <320>; + touchscreen-size-y = <480>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; diff --git a/dts/Bindings/input/touchscreen/imx6ul_tsc.txt b/dts/Bindings/input/touchscreen/imx6ul_tsc.txt new file mode 100644 index 0000000000..853dff96dd --- /dev/null +++ b/dts/Bindings/input/touchscreen/imx6ul_tsc.txt @@ -0,0 +1,36 @@ +* Freescale i.MX6UL Touch Controller + +Required properties: +- compatible: must be "fsl,imx6ul-tsc". +- reg: this touch controller address and the ADC2 address. +- interrupts: the interrupt of this touch controller and ADC2. +- clocks: the root clock of touch controller and ADC2. +- clock-names; must be "tsc" and "adc". +- xnur-gpio: the X- gpio this controller connect to. + This xnur-gpio returns to low once the finger leave the touch screen (The + last touch event the touch controller capture). + +Optional properties: +- measure-delay-time: the value of measure delay time. + Before X-axis or Y-axis measurement, the screen need some time before + even potential distribution ready. + This value depends on the touch screen. +- pre-charge-time: the touch screen need some time to precharge. + This value depends on the touch screen. + +Example: + tsc: tsc@02040000 { + compatible = "fsl,imx6ul-tsc"; + reg = <0x02040000 0x4000>, <0x0219c000 0x4000>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6UL_CLK_IPG>, + <&clks IMX6UL_CLK_ADC2>; + clock-names = "tsc", "adc"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc>; + xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; + measure-delay-time = <0xfff>; + pre-charge-time = <0xffff>; + status = "okay"; + }; diff --git a/dts/Bindings/input/touchscreen/pixcir_i2c_ts.txt b/dts/Bindings/input/touchscreen/pixcir_i2c_ts.txt index 6e551090f4..8eb240a287 100644 --- a/dts/Bindings/input/touchscreen/pixcir_i2c_ts.txt +++ b/dts/Bindings/input/touchscreen/pixcir_i2c_ts.txt @@ -8,6 +8,9 @@ Required properties: - touchscreen-size-x: horizontal resolution of touchscreen (in pixels) - touchscreen-size-y: vertical resolution of touchscreen (in pixels) +Optional properties: +- reset-gpio: GPIO connected to the RESET line of the chip + Example: i2c@00000000 { diff --git a/dts/Bindings/input/touchscreen/tsc2005.txt b/dts/Bindings/input/touchscreen/tsc2005.txt index 09089a6d69..b80c04b0e5 100644 --- a/dts/Bindings/input/touchscreen/tsc2005.txt +++ b/dts/Bindings/input/touchscreen/tsc2005.txt @@ -1,14 +1,15 @@ -* Texas Instruments tsc2005 touchscreen controller +* Texas Instruments tsc2004 and tsc2005 touchscreen controllers Required properties: - - compatible : "ti,tsc2005" - - reg : SPI device address - - spi-max-frequency : Maximal SPI speed + - compatible : "ti,tsc2004" or "ti,tsc2005" + - reg : Device address - interrupts : IRQ specifier - - reset-gpios : GPIO specifier - - vio-supply : Regulator specifier + - spi-max-frequency : Maximum SPI clocking speed of the device + (for tsc2005) Optional properties: + - vio-supply : Regulator specifier + - reset-gpios : GPIO specifier for the controller reset line - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates in ohm (defaults to 280) - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after @@ -18,6 +19,27 @@ Optional properties: Example: +&i2c3 { + tsc2004@48 { + compatible = "ti,tsc2004"; + reg = <0x48>; + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; + interrupts-extended = <&gpio1 27 IRQ_TYPE_EDGE_RISING>; + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +} + &mcspi1 { tsc2005@0 { compatible = "ti,tsc2005"; diff --git a/dts/Bindings/input/touchscreen/zforce_ts.txt b/dts/Bindings/input/touchscreen/zforce_ts.txt index 80c37df940..e3c27c4fd9 100644 --- a/dts/Bindings/input/touchscreen/zforce_ts.txt +++ b/dts/Bindings/input/touchscreen/zforce_ts.txt @@ -4,12 +4,12 @@ Required properties: - compatible: must be "neonode,zforce" - reg: I2C address of the chip - interrupts: interrupt to which the chip is connected -- gpios: gpios the chip is connected to - first one is the interrupt gpio and second one the reset gpio +- reset-gpios: reset gpio the chip is connected to - x-size: horizontal resolution of touchscreen - y-size: vertical resolution of touchscreen Optional properties: +- irq-gpios : interrupt gpio the chip is connected to - vdd-supply: Regulator controlling the controller supply Example: @@ -23,8 +23,8 @@ Example: interrupts = <2 0>; vdd-supply = <®_zforce_vdd>; - gpios = <&gpio5 6 0>, /* INT */ - <&gpio5 9 0>; /* RST */ + reset-gpios = <&gpio5 9 0>; /* RST */ + irq-gpios = <&gpio5 6 0>; /* IRQ, optional */ x-size = <800>; y-size = <600>; |