diff options
Diffstat (limited to 'dts/Bindings/interrupt-controller')
| -rw-r--r-- | dts/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt | 26 | ||||
| -rw-r--r-- | dts/Bindings/interrupt-controller/mips-gic.txt | 55 |
2 files changed, 73 insertions, 8 deletions
diff --git a/dts/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt b/dts/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt index ff812a8a82..bae1f21872 100644 --- a/dts/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt +++ b/dts/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt @@ -13,7 +13,12 @@ Such an interrupt controller has the following hardware design: or if they will output an interrupt signal at this 2nd level interrupt controller, in particular for UARTs -- not all 32-bits within the interrupt controller actually map to an interrupt +- typically has one 32-bit enable word and one 32-bit status word, but on + some hardware may have more than one enable/status pair + +- no atomic set/clear operations + +- not all bits within the interrupt controller actually map to an interrupt The typical hardware layout for this controller is represented below: @@ -48,7 +53,9 @@ The typical hardware layout for this controller is represented below: Required properties: - compatible: should be "brcm,bcm7120-l2-intc" -- reg: specifies the base physical address and size of the registers +- reg: specifies the base physical address and size of the registers; + multiple pairs may be specified, with the first pair handling IRQ offsets + 0..31 and the second pair handling 32..63 - interrupt-controller: identifies the node as an interrupt controller - #interrupt-cells: specifies the number of cells needed to encode an interrupt source, should be 1. @@ -59,18 +66,21 @@ Required properties: - brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts are wired to this 2nd level interrupt controller, and how they match their respective interrupt parents. Should match exactly the number of interrupts - specified in the 'interrupts' property. + specified in the 'interrupts' property, multiplied by the number of + enable/status register pairs implemented by this controller. For + multiple parent IRQs with multiple enable/status words, this looks like: + <irq0_w0 irq0_w1 irq1_w0 irq1_w1 ...> Optional properties: - brcm,irq-can-wake: if present, this means the L2 controller can be used as a wakeup source for system suspend/resume. -- brcm,int-fwd-mask: if present, a 32-bits bit mask to configure for the - interrupts which have a mux gate, typically UARTs. Setting these bits will - make their respective interrupts outputs bypass this 2nd level interrupt - controller completely, it completely transparent for the interrupt controller - parent +- brcm,int-fwd-mask: if present, a bit mask to configure the interrupts which + have a mux gate, typically UARTs. Setting these bits will make their + respective interrupt outputs bypass this 2nd level interrupt controller + completely; it is completely transparent for the interrupt controller + parent. This should have one 32-bit word per enable/status pair. Example: diff --git a/dts/Bindings/interrupt-controller/mips-gic.txt b/dts/Bindings/interrupt-controller/mips-gic.txt new file mode 100644 index 0000000000..5a65478e5d --- /dev/null +++ b/dts/Bindings/interrupt-controller/mips-gic.txt @@ -0,0 +1,55 @@ +MIPS Global Interrupt Controller (GIC) + +The MIPS GIC routes external interrupts to individual VPEs and IRQ pins. +It also supports local (per-processor) interrupts and software-generated +interrupts which can be used as IPIs. The GIC also includes a free-running +global timer, per-CPU count/compare timers, and a watchdog. + +Required properties: +- compatible : Should be "mti,gic". +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt specifier. Should be 3. + - The first cell is the type of interrupt, local or shared. + See <include/dt-bindings/interrupt-controller/mips-gic.h>. + - The second cell is the GIC interrupt number. + - The third cell encodes the interrupt flags. + See <include/dt-bindings/interrupt-controller/irq.h> for a list of valid + flags. + +Optional properties: +- reg : Base address and length of the GIC registers. If not present, + the base address reported by the hardware GCR_GIC_BASE will be used. +- mti,reserved-cpu-vectors : Specifies the list of CPU interrupt vectors + to which the GIC may not route interrupts. Valid values are 2 - 7. + This property is ignored if the CPU is started in EIC mode. + +Required properties for timer sub-node: +- compatible : Should be "mti,gic-timer". +- interrupts : Interrupt for the GIC local timer. +- clock-frequency : Clock frequency at which the GIC timers operate. + +Example: + + gic: interrupt-controller@1bdc0000 { + compatible = "mti,gic"; + reg = <0x1bdc0000 0x20000>; + + interrupt-controller; + #interrupt-cells = <3>; + + mti,reserved-cpu-vectors = <7>; + + timer { + compatible = "mti,gic-timer"; + interrupts = <GIC_LOCAL 1 IRQ_TYPE_NONE>; + clock-frequency = <50000000>; + }; + }; + + uart@18101400 { + ... + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>; + ... + }; |