diff options
Diffstat (limited to 'dts/Bindings/media/i2c')
| -rw-r--r-- | dts/Bindings/media/i2c/mt9m111.txt | 4 | ||||
| -rw-r--r-- | dts/Bindings/media/i2c/ov5640.txt | 46 | ||||
| -rw-r--r-- | dts/Bindings/media/i2c/ov7740.txt | 47 | ||||
| -rw-r--r-- | dts/Bindings/media/i2c/toshiba,et8ek8.txt | 7 |
4 files changed, 102 insertions, 2 deletions
diff --git a/dts/Bindings/media/i2c/mt9m111.txt b/dts/Bindings/media/i2c/mt9m111.txt index ed5a334b1e..6b910036b5 100644 --- a/dts/Bindings/media/i2c/mt9m111.txt +++ b/dts/Bindings/media/i2c/mt9m111.txt @@ -6,6 +6,8 @@ interface. Required Properties: - compatible: value should be "micron,mt9m111" +- clocks: reference to the master clock. +- clock-names: shall be "mclk". For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. @@ -16,6 +18,8 @@ Example: mt9m111@5d { compatible = "micron,mt9m111"; reg = <0x5d>; + clocks = <&mclk>; + clock-names = "mclk"; remote = <&pxa_camera>; port { diff --git a/dts/Bindings/media/i2c/ov5640.txt b/dts/Bindings/media/i2c/ov5640.txt index 540b36c4b1..8e36da0d84 100644 --- a/dts/Bindings/media/i2c/ov5640.txt +++ b/dts/Bindings/media/i2c/ov5640.txt @@ -1,4 +1,4 @@ -* Omnivision OV5640 MIPI CSI-2 sensor +* Omnivision OV5640 MIPI CSI-2 / parallel sensor Required Properties: - compatible: should be "ovti,ov5640" @@ -18,7 +18,25 @@ The device node must contain one 'port' child node for its digital output video port, in accordance with the video interface bindings defined in Documentation/devicetree/bindings/media/video-interfaces.txt. -Example: +OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint. + +Endpoint node required properties for CSI-2 connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- clock-lanes: should be set to <0> (clock lane on hardware lane 0) +- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported) + +Endpoint node required properties for parallel connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- bus-width: shall be set to <8> for 8 bits parallel bus + or <10> for 10 bits parallel bus +- data-shift: shall be set to <2> for 8 bits parallel bus + (lines 9:2 are used) or <0> for 10 bits parallel bus +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. +- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock + signal. + +Examples: &i2c1 { ov5640: camera@3c { @@ -35,6 +53,7 @@ Example: reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; port { + /* MIPI CSI-2 bus endpoint */ ov5640_to_mipi_csi2: endpoint { remote-endpoint = <&mipi_csi2_from_ov5640>; clock-lanes = <0>; @@ -43,3 +62,26 @@ Example: }; }; }; + +&i2c1 { + ov5640: camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + clock-names = "xclk"; + + port { + /* Parallel bus endpoint */ + ov5640_to_parallel: endpoint { + remote-endpoint = <¶llel_from_ov5640>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; +}; diff --git a/dts/Bindings/media/i2c/ov7740.txt b/dts/Bindings/media/i2c/ov7740.txt new file mode 100644 index 0000000000..af781c3a5f --- /dev/null +++ b/dts/Bindings/media/i2c/ov7740.txt @@ -0,0 +1,47 @@ +* Omnivision OV7740 CMOS image sensor + +The Omnivision OV7740 image sensor supports multiple output image +size, such as VGA, and QVGA, CIF and any size smaller. It also +supports the RAW RGB and YUV output formats. + +The common video interfaces bindings (see video-interfaces.txt) should +be used to specify link to the image data receiver. The OV7740 device +node should contain one 'port' child node with an 'endpoint' subnode. + +Required Properties: +- compatible: "ovti,ov7740". +- reg: I2C slave address of the sensor. +- clocks: Reference to the xvclk input clock. +- clock-names: "xvclk". + +Optional Properties: +- reset-gpios: Rreference to the GPIO connected to the reset_b pin, + if any. Active low with pull-ip resistor. +- powerdown-gpios: Reference to the GPIO connected to the pwdn pin, + if any. Active high with pull-down resistor. + +Endpoint node mandatory properties: +- remote-endpoint: A phandle to the bus receiver's endpoint node. + +Example: + + i2c1: i2c@fc028000 { + ov7740: camera@21 { + compatible = "ovti,ov7740"; + reg = <0x21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>; + clocks = <&isc>; + clock-names = "xvclk"; + assigned-clocks = <&isc>; + assigned-clock-rates = <24000000>; + reset-gpios = <&pioA 43 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pioA 44 GPIO_ACTIVE_HIGH>; + + port { + ov7740_0: endpoint { + remote-endpoint = <&isc_0>; + }; + }; + }; + }; diff --git a/dts/Bindings/media/i2c/toshiba,et8ek8.txt b/dts/Bindings/media/i2c/toshiba,et8ek8.txt index 0b7b6a4d84..e80d5891b7 100644 --- a/dts/Bindings/media/i2c/toshiba,et8ek8.txt +++ b/dts/Bindings/media/i2c/toshiba,et8ek8.txt @@ -20,6 +20,13 @@ Mandatory properties is in hardware standby mode when the signal is in the low state. +Optional properties +------------------- + +- flash-leds: See ../video-interfaces.txt +- lens-focus: See ../video-interfaces.txt + + Endpoint node mandatory properties ---------------------------------- |