diff options
Diffstat (limited to 'dts/Bindings/media')
| -rw-r--r-- | dts/Bindings/media/i2c/mt9v032.txt | 2 | ||||
| -rw-r--r-- | dts/Bindings/media/i2c/tvp5150.txt | 45 | ||||
| -rw-r--r-- | dts/Bindings/media/rcar_vin.txt | 1 | ||||
| -rw-r--r-- | dts/Bindings/media/renesas,jpu.txt | 13 | ||||
| -rw-r--r-- | dts/Bindings/media/renesas,vsp1.txt | 34 | ||||
| -rw-r--r-- | dts/Bindings/media/ti-cal.txt | 72 |
6 files changed, 135 insertions, 32 deletions
diff --git a/dts/Bindings/media/i2c/mt9v032.txt b/dts/Bindings/media/i2c/mt9v032.txt index 202565313e..100f0ae432 100644 --- a/dts/Bindings/media/i2c/mt9v032.txt +++ b/dts/Bindings/media/i2c/mt9v032.txt @@ -20,6 +20,8 @@ Optional Properties: - link-frequencies: List of allowed link frequencies in Hz. Each frequency is expressed as a 64-bit big-endian integer. +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. diff --git a/dts/Bindings/media/i2c/tvp5150.txt b/dts/Bindings/media/i2c/tvp5150.txt new file mode 100644 index 0000000000..8c0fc1a26b --- /dev/null +++ b/dts/Bindings/media/i2c/tvp5150.txt @@ -0,0 +1,45 @@ +* Texas Instruments TVP5150 and TVP5151 video decoders + +The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL +(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV +with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats. + +Required Properties: +- compatible: value must be "ti,tvp5150" +- reg: I2C slave address + +Optional Properties: +- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any. +- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Required Endpoint Properties for parallel synchronization: + +- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH). +- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH). +- field-even-active: field signal level during the even field data + transmission. Must be <0>. + +If none of hsync-active, vsync-active and field-even-active is specified, +the endpoint is assumed to use embedded BT.656 synchronization. + +Example: + +&i2c2 { + ... + tvp5150@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>; + + port { + tvp5150_1: endpoint { + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; diff --git a/dts/Bindings/media/rcar_vin.txt b/dts/Bindings/media/rcar_vin.txt index 9dafe6b06c..619193ccf7 100644 --- a/dts/Bindings/media/rcar_vin.txt +++ b/dts/Bindings/media/rcar_vin.txt @@ -6,6 +6,7 @@ family of devices. The current blocks are always slaves and suppot one input channel which can be either RGB, YUYV or BT656. - compatible: Must be one of the following + - "renesas,vin-r8a7795" for the R8A7795 device - "renesas,vin-r8a7794" for the R8A7794 device - "renesas,vin-r8a7793" for the R8A7793 device - "renesas,vin-r8a7791" for the R8A7791 device diff --git a/dts/Bindings/media/renesas,jpu.txt b/dts/Bindings/media/renesas,jpu.txt index 0cb94201bf..d3436e5190 100644 --- a/dts/Bindings/media/renesas,jpu.txt +++ b/dts/Bindings/media/renesas,jpu.txt @@ -5,11 +5,12 @@ and decoding function conforming to the JPEG baseline process, so that the JPU can encode image data and decode JPEG data quickly. Required properties: - - compatible: should containg one of the following: - - "renesas,jpu-r8a7790" for R-Car H2 - - "renesas,jpu-r8a7791" for R-Car M2-W - - "renesas,jpu-r8a7792" for R-Car V2H - - "renesas,jpu-r8a7793" for R-Car M2-N +- compatible: "renesas,jpu-<soctype>", "renesas,rcar-gen2-jpu" as fallback. + Examples with soctypes are: + - "renesas,jpu-r8a7790" for R-Car H2 + - "renesas,jpu-r8a7791" for R-Car M2-W + - "renesas,jpu-r8a7792" for R-Car V2H + - "renesas,jpu-r8a7793" for R-Car M2-N - reg: Base address and length of the registers block for the JPU. - interrupts: JPU interrupt specifier. @@ -17,7 +18,7 @@ Required properties: Example: R8A7790 (R-Car H2) JPU node jpeg-codec@fe980000 { - compatible = "renesas,jpu-r8a7790"; + compatible = "renesas,jpu-r8a7790", "renesas,rcar-gen2-jpu"; reg = <0 0xfe980000 0 0x10300>; interrupts = <0 272 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_JPU>; diff --git a/dts/Bindings/media/renesas,vsp1.txt b/dts/Bindings/media/renesas,vsp1.txt index 87fe08abf3..627405abd1 100644 --- a/dts/Bindings/media/renesas,vsp1.txt +++ b/dts/Bindings/media/renesas,vsp1.txt @@ -1,30 +1,18 @@ -* Renesas VSP1 Video Processing Engine +* Renesas VSP Video Processing Engine -The VSP1 is a video processing engine that supports up-/down-scaling, alpha +The VSP is a video processing engine that supports up-/down-scaling, alpha blending, color space conversion and various other image processing features. It can be found in the Renesas R-Car second generation SoCs. Required properties: - - compatible: Must contain "renesas,vsp1" + - compatible: Must contain one of the following values + - "renesas,vsp1" for the R-Car Gen2 VSP1 + - "renesas,vsp2" for the R-Car Gen3 VSP2 - - reg: Base address and length of the registers block for the VSP1. - - interrupts: VSP1 interrupt specifier. - - clocks: A phandle + clock-specifier pair for the VSP1 functional clock. - - - renesas,#rpf: Number of Read Pixel Formatter (RPF) modules in the VSP1. - - renesas,#uds: Number of Up Down Scaler (UDS) modules in the VSP1. - - renesas,#wpf: Number of Write Pixel Formatter (WPF) modules in the VSP1. - - -Optional properties: - - - renesas,has-lif: Boolean, indicates that the LCD Interface (LIF) module is - available. - - renesas,has-lut: Boolean, indicates that the Look Up Table (LUT) module is - available. - - renesas,has-sru: Boolean, indicates that the Super Resolution Unit (SRU) - module is available. + - reg: Base address and length of the registers block for the VSP. + - interrupts: VSP interrupt specifier. + - clocks: A phandle + clock-specifier pair for the VSP functional clock. Example: R8A7790 (R-Car H2) VSP1-S node @@ -34,10 +22,4 @@ Example: R8A7790 (R-Car H2) VSP1-S node reg = <0 0xfe928000 0 0x8000>; interrupts = <0 267 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>; - - renesas,has-lut; - renesas,has-sru; - renesas,#rpf = <5>; - renesas,#uds = <3>; - renesas,#wpf = <4>; }; diff --git a/dts/Bindings/media/ti-cal.txt b/dts/Bindings/media/ti-cal.txt new file mode 100644 index 0000000000..ae9b52f375 --- /dev/null +++ b/dts/Bindings/media/ti-cal.txt @@ -0,0 +1,72 @@ +Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) +------------------------------------------------------ + +The Camera Adaptation Layer (CAL) is a key component for image capture +applications. The capture module provides the system interface and the +processing capability to connect CSI2 image-sensor modules to the +DRA72x device. + +Required properties: +- compatible: must be "ti,dra72-cal" +- reg: CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX + control address space +- reg-names: cal_top, cal_rx_core0, cal_rx_core1, and camerrx_control + registers +- interrupts: should contain IRQ line for the CAL; + +CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes +should contain a 'port' child node with child 'endpoint' node. Please +refer to the bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + cal: cal@4845b000 { + compatible = "ti,dra72-cal"; + ti,hwmods = "cal"; + reg = <0x4845B000 0x400>, + <0x4845B800 0x40>, + <0x4845B900 0x40>, + <0x4A002e94 0x4>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1", + "camerrx_control"; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + endpoint { + slave-mode; + remote-endpoint = <&ar0330_1>; + }; + }; + csi2_1: port@1 { + reg = <1>; + }; + }; + }; + + i2c5: i2c@4807c000 { + ar0330@10 { + compatible = "ti,ar0330"; + reg = <0x10>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + ar0330_1: endpoint { + reg = <0>; + clock-lanes = <1>; + data-lanes = <0 2 3 4>; + remote-endpoint = <&csi2_0>; + }; + }; + }; + }; |