diff options
Diffstat (limited to 'dts/Bindings/memory-controllers/ti,gpmc-child.yaml')
| -rw-r--r-- | dts/Bindings/memory-controllers/ti,gpmc-child.yaml | 252 |
1 files changed, 252 insertions, 0 deletions
diff --git a/dts/Bindings/memory-controllers/ti,gpmc-child.yaml b/dts/Bindings/memory-controllers/ti,gpmc-child.yaml new file mode 100644 index 0000000000..383d19e0ba --- /dev/null +++ b/dts/Bindings/memory-controllers/ti,gpmc-child.yaml @@ -0,0 +1,252 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc-child.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments GPMC Bus Child Nodes + +maintainers: + - Tony Lindgren <tony@atomide.com> + - Roger Quadros <rogerq@kernel.org> + +description: + This binding is meant for the child nodes of the GPMC node. The node + represents any device connected to the GPMC bus. It may be a Flash chip, + RAM chip or Ethernet controller, etc. These properties are meant for + configuring the GPMC settings/timings and will accompany the bindings + supported by the respective device. + +properties: + reg: true + +# GPMC Timing properties for child nodes. All are optional and default to 0. + gpmc,sync-clk-ps: + description: Minimum clock period for synchronous mode + default: 0 + +# Chip-select signal timings corresponding to GPMC_CONFIG2: + gpmc,cs-on-ns: + description: Assertion time + default: 0 + + gpmc,cs-rd-off-ns: + description: Read deassertion time + default: 0 + + gpmc,cs-wr-off-ns: + description: Write deassertion time + default: 0 + +# ADV signal timings corresponding to GPMC_CONFIG3: + gpmc,adv-on-ns: + description: Assertion time + default: 0 + + gpmc,adv-rd-off-ns: + description: Read deassertion time + default: 0 + + gpmc,adv-wr-off-ns: + description: Write deassertion time + default: 0 + + gpmc,adv-aad-mux-on-ns: + description: Assertion time for AAD + default: 0 + + gpmc,adv-aad-mux-rd-off-ns: + description: Read deassertion time for AAD + default: 0 + + gpmc,adv-aad-mux-wr-off-ns: + description: Write deassertion time for AAD + default: 0 + +# WE signals timings corresponding to GPMC_CONFIG4: + gpmc,we-on-ns: + description: Assertion time + default: 0 + + gpmc,we-off-ns: + description: Deassertion time + default: 0 + +# OE signals timings corresponding to GPMC_CONFIG4: + gpmc,oe-on-ns: + description: Assertion time + default: 0 + + gpmc,oe-off-ns: + description: Deassertion time + default: 0 + + gpmc,oe-aad-mux-on-ns: + description: Assertion time for AAD + default: 0 + + gpmc,oe-aad-mux-off-ns: + description: Deassertion time for AAD + default: 0 + +# Access time and cycle time timings (in nanoseconds) corresponding to +# GPMC_CONFIG5: + gpmc,page-burst-access-ns: + description: Multiple access word delay + default: 0 + + gpmc,access-ns: + description: Start-cycle to first data valid delay + default: 0 + + gpmc,rd-cycle-ns: + description: Total read cycle time + default: 0 + + gpmc,wr-cycle-ns: + description: Total write cycle time + default: 0 + + gpmc,bus-turnaround-ns: + description: Turn-around time between successive accesses + default: 0 + + gpmc,cycle2cycle-delay-ns: + description: Delay between chip-select pulses + default: 0 + + gpmc,clk-activation-ns: + description: GPMC clock activation time + default: 0 + + gpmc,wait-monitoring-ns: + description: Start of wait monitoring with regard to valid data + default: 0 + +# Boolean timing parameters. If property is present, parameter is enabled +# otherwise disabled. + gpmc,adv-extra-delay: + description: ADV signal is delayed by half GPMC clock + type: boolean + + gpmc,cs-extra-delay: + description: CS signal is delayed by half GPMC clock + type: boolean + + gpmc,cycle2cycle-diffcsen: + description: | + Add "cycle2cycle-delay" between successive accesses + to a different CS + type: boolean + + gpmc,cycle2cycle-samecsen: + description: | + Add "cycle2cycle-delay" between successive accesses + to the same CS + type: boolean + + gpmc,oe-extra-delay: + description: OE signal is delayed by half GPMC clock + type: boolean + + gpmc,we-extra-delay: + description: WE signal is delayed by half GPMC clock + type: boolean + + gpmc,time-para-granularity: + description: Multiply all access times by 2 + type: boolean + +# The following two properties are applicable only to OMAP3+ and AM335x: + gpmc,wr-access-ns: + description: | + In synchronous write mode, for single or + burst accesses, defines the number of + GPMC_FCLK cycles from start access time + to the GPMC_CLK rising edge used by the + memory device for the first data capture. + default: 0 + + gpmc,wr-data-mux-bus-ns: + description: | + In address-data multiplex mode, specifies + the time when the first data is driven on + the address-data bus. + default: 0 + +# GPMC chip-select settings properties for child nodes. All are optional. + gpmc,burst-length: + description: Page/burst length. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 4, 8, 16] + default: 0 + + gpmc,burst-wrap: + description: Enables wrap bursting + type: boolean + + gpmc,burst-read: + description: Enables read page/burst mode + type: boolean + + gpmc,burst-write: + description: Enables write page/burst mode + type: boolean + + gpmc,device-width: + description: | + Total width of device(s) connected to a GPMC + chip-select in bytes. The GPMC supports 8-bit + and 16-bit devices and so this property must be + 1 or 2. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2] + default: 1 + + gpmc,mux-add-data: + description: | + Address and data multiplexing configuration. + Valid values are + 0 for Non multiplexed mode + 1 for address-address-data multiplexing mode and + 2 for address-data multiplexing mode. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + gpmc,sync-read: + description: | + Enables synchronous read. Defaults to asynchronous + is this is not set. + type: boolean + + gpmc,sync-write: + description: | + Enables synchronous writes. Defaults to asynchronous + is this is not set. + type: boolean + + gpmc,wait-pin: + description: | + Wait-pin used by client. Must be less than "gpmc,num-waitpins". + $ref: /schemas/types.yaml#/definitions/uint32 + + ti,wait-pin-polarity: + description: | + Set the desired polarity for the selected wait pin. + 0 for active low, 1 for active high. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + + gpmc,wait-on-read: + description: Enables wait monitoring on reads. + type: boolean + + gpmc,wait-on-write: + description: Enables wait monitoring on writes. + type: boolean + +required: + - reg + +# the GPMC child will have its own native properties +additionalProperties: true |