diff options
Diffstat (limited to 'dts/Bindings/memory-controllers')
| -rw-r--r-- | dts/Bindings/memory-controllers/exynos-srom.txt | 79 | ||||
| -rw-r--r-- | dts/Bindings/memory-controllers/nvidia,tegra124-emc.txt (renamed from dts/Bindings/memory-controllers/tegra-emc.txt) | 4 | ||||
| -rw-r--r-- | dts/Bindings/memory-controllers/nvidia,tegra30-mc.txt (renamed from dts/Bindings/memory-controllers/nvidia,tegra-mc.txt) | 6 | ||||
| -rw-r--r-- | dts/Bindings/memory-controllers/omap-gpmc.txt | 152 |
4 files changed, 236 insertions, 5 deletions
diff --git a/dts/Bindings/memory-controllers/exynos-srom.txt b/dts/Bindings/memory-controllers/exynos-srom.txt new file mode 100644 index 0000000000..f633b5d0f8 --- /dev/null +++ b/dts/Bindings/memory-controllers/exynos-srom.txt @@ -0,0 +1,79 @@ +SAMSUNG Exynos SoCs SROM Controller driver. + +Required properties: +- compatible : Should contain "samsung,exynos4210-srom". + +- reg: offset and length of the register set + +Optional properties: +The SROM controller can be used to attach external peripherals. In this case +extra properties, describing the bus behind it, should be specified as below: + +- #address-cells: Must be set to 2 to allow device address translation. + Address is specified as (bank#, offset). + +- #size-cells: Must be set to 1 to allow device size passing + +- ranges: Must be set up to reflect the memory layout with four integer values + per bank: + <bank-number> 0 <parent address of bank> <size> + +Sub-nodes: +The actual device nodes should be added as subnodes to the SROMc node. These +subnodes, in addition to regular device specification, should contain the following +properties, describing configuration of the relevant SROM bank: + +Required properties: +- reg: bank number, base address (relative to start of the bank) and size of + the memory mapped for the device. Note that base address will be + typically 0 as this is the start of the bank. + +- samsung,srom-timing : array of 6 integers, specifying bank timings in the + following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. + Each value is specified in cycles and has the following + meaning and valid range: + Tacp : Page mode access cycle at Page mode (0 - 15) + Tcah : Address holding time after CSn (0 - 15) + Tcoh : Chip selection hold on OEn (0 - 15) + Tacc : Access cycle (0 - 31, the actual time is N + 1) + Tcos : Chip selection set-up before OEn (0 - 15) + Tacs : Address set-up before CSn (0 - 15) + +Optional properties: +- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used. + +- samsung,srom-page-mode : if page mode is set, 4 data page mode will be configured, + else normal (1 data) page mode will be set. + +Example: basic definition, no banks are configured + memory-controller@12570000 { + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + }; + +Example: SROMc with SMSC911x ethernet chip on bank 3 + memory-controller@12570000 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x04000000 0x20000 // Bank0 + 1 0 0x05000000 0x20000 // Bank1 + 2 0 0x06000000 0x20000 // Bank2 + 3 0 0x07000000 0x20000>; // Bank3 + + compatible = "samsung,exynos4210-srom"; + reg = <0x12570000 0x14>; + + ethernet@3,0 { + compatible = "smsc,lan9115"; + reg = <3 0 0x10000>; // Bank 3, offset = 0 + phy-mode = "mii"; + interrupt-parent = <&gpx0>; + interrupts = <5 8>; + reg-io-width = <2>; + smsc,irq-push-pull; + smsc,force-internal-phy; + + samsung,srom-page-mode; + samsung,srom-timing = <9 12 1 9 1 1>; + }; + }; diff --git a/dts/Bindings/memory-controllers/tegra-emc.txt b/dts/Bindings/memory-controllers/nvidia,tegra124-emc.txt index b59c625d63..ba0bc3f124 100644 --- a/dts/Bindings/memory-controllers/tegra-emc.txt +++ b/dts/Bindings/memory-controllers/nvidia,tegra124-emc.txt @@ -190,7 +190,7 @@ be specified, according to the board documentation: Example SoC include file: / { - emc@0,7001b000 { + emc@7001b000 { compatible = "nvidia,tegra124-emc"; reg = <0x0 0x7001b000 0x0 0x1000>; @@ -201,7 +201,7 @@ Example SoC include file: Example board file: / { - emc@0,7001b000 { + emc@7001b000 { emc-timings-3 { nvidia,ram-code = <3>; diff --git a/dts/Bindings/memory-controllers/nvidia,tegra-mc.txt b/dts/Bindings/memory-controllers/nvidia,tegra30-mc.txt index 3338a2834a..8dbe47013c 100644 --- a/dts/Bindings/memory-controllers/nvidia,tegra-mc.txt +++ b/dts/Bindings/memory-controllers/nvidia,tegra30-mc.txt @@ -61,7 +61,7 @@ specified, according to the board documentation: Example SoC include file: / { - mc: memory-controller@0,70019000 { + mc: memory-controller@70019000 { compatible = "nvidia,tegra124-mc"; reg = <0x0 0x70019000 0x0 0x1000>; clocks = <&tegra_car TEGRA124_CLK_MC>; @@ -72,7 +72,7 @@ Example SoC include file: #iommu-cells = <1>; }; - sdhci@0,700b0000 { + sdhci@700b0000 { compatible = "nvidia,tegra124-sdhci"; ... iommus = <&mc TEGRA_SWGROUP_SDMMC1A>; @@ -82,7 +82,7 @@ Example SoC include file: Example board file: / { - memory-controller@0,70019000 { + memory-controller@70019000 { emc-timings-3 { nvidia,ram-code = <3>; diff --git a/dts/Bindings/memory-controllers/omap-gpmc.txt b/dts/Bindings/memory-controllers/omap-gpmc.txt new file mode 100644 index 0000000000..21055e2102 --- /dev/null +++ b/dts/Bindings/memory-controllers/omap-gpmc.txt @@ -0,0 +1,152 @@ +Device tree bindings for OMAP general purpose memory controllers (GPMC) + +The actual devices are instantiated from the child nodes of a GPMC node. + +Required properties: + + - compatible: Should be set to one of the following: + + ti,omap2420-gpmc (omap2420) + ti,omap2430-gpmc (omap2430) + ti,omap3430-gpmc (omap3430 & omap3630) + ti,omap4430-gpmc (omap4430 & omap4460 & omap543x) + ti,am3352-gpmc (am335x devices) + + - reg: A resource specifier for the register space + (see the example below) + - ti,hwmods: Should be set to "ti,gpmc" until the DT transition is + completed. + - #address-cells: Must be set to 2 to allow memory address translation + - #size-cells: Must be set to 1 to allow CS address passing + - gpmc,num-cs: The maximum number of chip-select lines that controller + can support. + - gpmc,num-waitpins: The maximum number of wait pins that controller can + support. + - ranges: Must be set up to reflect the memory layout with four + integer values for each chip-select line in use: + + <cs-number> 0 <physical address of mapping> <size> + + Currently, calculated values derived from the contents + of the per-CS register GPMC_CONFIG7 (as set up by the + bootloader) are used for the physical address decoding. + As this will change in the future, filling correct + values here is a requirement. + - interrupt-controller: The GPMC driver implements and interrupt controller for + the NAND events "fifoevent" and "termcount" plus the + rising/falling edges on the GPMC_WAIT pins. + The interrupt number mapping is as follows + 0 - NAND_fifoevent + 1 - NAND_termcount + 2 - GPMC_WAIT0 pin edge + 3 - GPMC_WAIT1 pin edge, and so on. + - interrupt-cells: Must be set to 2 + - gpio-controller: The GPMC driver implements a GPIO controller for the + GPMC WAIT pins that can be used as general purpose inputs. + 0 maps to GPMC_WAIT0 pin. + - gpio-cells: Must be set to 2 + +Timing properties for child nodes. All are optional and default to 0. + + - gpmc,sync-clk-ps: Minimum clock period for synchronous mode, in picoseconds + + Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2: + - gpmc,cs-on-ns: Assertion time + - gpmc,cs-rd-off-ns: Read deassertion time + - gpmc,cs-wr-off-ns: Write deassertion time + + ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3: + - gpmc,adv-on-ns: Assertion time + - gpmc,adv-rd-off-ns: Read deassertion time + - gpmc,adv-wr-off-ns: Write deassertion time + - gpmc,adv-aad-mux-on-ns: Assertion time for AAD + - gpmc,adv-aad-mux-rd-off-ns: Read deassertion time for AAD + - gpmc,adv-aad-mux-wr-off-ns: Write deassertion time for AAD + + WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: + - gpmc,we-on-ns Assertion time + - gpmc,we-off-ns: Deassertion time + + OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: + - gpmc,oe-on-ns: Assertion time + - gpmc,oe-off-ns: Deassertion time + - gpmc,oe-aad-mux-on-ns: Assertion time for AAD + - gpmc,oe-aad-mux-off-ns: Deassertion time for AAD + + Access time and cycle time timings (in nanoseconds) corresponding to + GPMC_CONFIG5: + - gpmc,page-burst-access-ns: Multiple access word delay + - gpmc,access-ns: Start-cycle to first data valid delay + - gpmc,rd-cycle-ns: Total read cycle time + - gpmc,wr-cycle-ns: Total write cycle time + - gpmc,bus-turnaround-ns: Turn-around time between successive accesses + - gpmc,cycle2cycle-delay-ns: Delay between chip-select pulses + - gpmc,clk-activation-ns: GPMC clock activation time + - gpmc,wait-monitoring-ns: Start of wait monitoring with regard to valid + data + +Boolean timing parameters. If property is present parameter enabled and +disabled if omitted: + - gpmc,adv-extra-delay: ADV signal is delayed by half GPMC clock + - gpmc,cs-extra-delay: CS signal is delayed by half GPMC clock + - gpmc,cycle2cycle-diffcsen: Add "cycle2cycle-delay" between successive + accesses to a different CS + - gpmc,cycle2cycle-samecsen: Add "cycle2cycle-delay" between successive + accesses to the same CS + - gpmc,oe-extra-delay: OE signal is delayed by half GPMC clock + - gpmc,we-extra-delay: WE signal is delayed by half GPMC clock + - gpmc,time-para-granularity: Multiply all access times by 2 + +The following are only applicable to OMAP3+ and AM335x: + - gpmc,wr-access-ns: In synchronous write mode, for single or + burst accesses, defines the number of + GPMC_FCLK cycles from start access time + to the GPMC_CLK rising edge used by the + memory device for the first data capture. + - gpmc,wr-data-mux-bus-ns: In address-data multiplex mode, specifies + the time when the first data is driven on + the address-data bus. + +GPMC chip-select settings properties for child nodes. All are optional. + +- gpmc,burst-length Page/burst length. Must be 4, 8 or 16. +- gpmc,burst-wrap Enables wrap bursting +- gpmc,burst-read Enables read page/burst mode +- gpmc,burst-write Enables write page/burst mode +- gpmc,device-width Total width of device(s) connected to a GPMC + chip-select in bytes. The GPMC supports 8-bit + and 16-bit devices and so this property must be + 1 or 2. +- gpmc,mux-add-data Address and data multiplexing configuration. + Valid values are 1 for address-address-data + multiplexing mode and 2 for address-data + multiplexing mode. +- gpmc,sync-read Enables synchronous read. Defaults to asynchronous + is this is not set. +- gpmc,sync-write Enables synchronous writes. Defaults to asynchronous + is this is not set. +- gpmc,wait-pin Wait-pin used by client. Must be less than + "gpmc,num-waitpins". +- gpmc,wait-on-read Enables wait monitoring on reads. +- gpmc,wait-on-write Enables wait monitoring on writes. + +Example for an AM33xx board: + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x50000000 0x2000>; + interrupts = <100>; + + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + /* child nodes go here */ + }; |