1 files changed, 0 insertions, 67 deletions
diff --git a/dts/Bindings/mmc/fsl-imx-esdhc.txt b/dts/Bindings/mmc/fsl-imx-esdhc.txt
deleted file mode 100644
index de1b8bd550..0000000000
--- a/dts/Bindings/mmc/fsl-imx-esdhc.txt
+++ /dev/null
@@ -1,67 +0,0 @@
-* Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX
-
-The Enhanced Secure Digital Host Controller on Freescale i.MX family
-provides an interface for MMC, SD, and SDIO types of memory cards.
-
-This file documents differences between the core properties described
-by mmc.txt and the properties used by the sdhci-esdhc-imx driver.
-
-Required properties:
-- compatible : Should be "fsl,<chip>-esdhc", the supported chips include
-	       "fsl,imx25-esdhc"
-	       "fsl,imx35-esdhc"
-	       "fsl,imx51-esdhc"
-	       "fsl,imx53-esdhc"
-	       "fsl,imx6q-usdhc"
-	       "fsl,imx6sl-usdhc"
-	       "fsl,imx6sx-usdhc"
-	       "fsl,imx6ull-usdhc"
-	       "fsl,imx7d-usdhc"
-	       "fsl,imx7ulp-usdhc"
-	       "fsl,imx8mq-usdhc"
-	       "fsl,imx8mm-usdhc"
-	       "fsl,imx8mn-usdhc"
-	       "fsl,imx8mp-usdhc"
-	       "fsl,imx8qm-usdhc"
-	       "fsl,imx8qxp-usdhc"
-
-Optional properties:
-- fsl,wp-controller : Indicate to use controller internal write protection
-- fsl,delay-line : Specify the number of delay cells for override mode.
-  This is used to set the clock delay for DLL(Delay Line) on override mode
-  to select a proper data sampling window in case the clock quality is not good
-  due to signal path is too long on the board. Please refer to eSDHC/uSDHC
-  chapter, DLL (Delay Line) section in RM for details.
-- voltage-ranges : Specify the voltage range in case there are software
-  transparent level shifters on the outputs of the controller. Two cells are
-  required, first cell specifies minimum slot voltage (mV), second cell
-  specifies maximum slot voltage (mV). Several ranges could be specified.
-- fsl,tuning-start-tap: Specify the start dealy cell point when send first CMD19
-  in tuning procedure.
-- fsl,tuning-step: Specify the increasing delay cell steps in tuning procedure.
-  The uSDHC use one delay cell as default increasing step to do tuning process.
-  This property allows user to change the tuning step to more than one delay
-  cells which is useful for some special boards or cards when the default
-  tuning step can't find the proper delay window within limited tuning retries.
-- fsl,strobe-dll-delay-target: Specify the strobe dll control slave delay target.
-  This delay target programming host controller loopback read clock, and this
-  property allows user to change the delay target for the strobe input read clock.
-  If not use this property, driver default set the delay target to value 7.
-  Only eMMC HS400 mode need to take care of this property.
-
-Examples:
-
-esdhc@70004000 {
-	compatible = "fsl,imx51-esdhc";
-	reg = <0x70004000 0x4000>;
-	interrupts = <1>;
-	fsl,wp-controller;
-};
-
-esdhc@70008000 {
-	compatible = "fsl,imx51-esdhc";
-	reg = <0x70008000 0x4000>;
-	interrupts = <2>;
-	cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */
-	wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */
-};