1 files changed, 0 insertions, 72 deletions
diff --git a/dts/Bindings/mmc/mmci.txt b/dts/Bindings/mmc/mmci.txt
deleted file mode 100644
index 6d3c626e01..0000000000
--- a/dts/Bindings/mmc/mmci.txt
+++ /dev/null
@@ -1,72 +0,0 @@
-* ARM PrimeCell MultiMedia Card Interface (MMCI) PL180/1
-
-The ARM PrimeCell MMCI PL180 and PL181 provides an interface for
-reading and writing to MultiMedia and SD cards alike.
-
-This file documents differences between the core properties described
-by mmc.txt and the properties used by the mmci driver. Using "st" as
-the prefix for a property, indicates support by the ST Micro variant.
-
-Required properties:
-- compatible             : contains "arm,pl18x", "arm,primecell".
-- vmmc-supply            : phandle to the regulator device tree node, mentioned
-                           as the VCC/VDD supply in the eMMC/SD specs.
-
-Optional properties:
-- arm,primecell-periphid : contains the PrimeCell Peripheral ID, it overrides
-                           the ID provided by the HW
-- resets                 : phandle to internal reset line.
-			   Should be defined for sdmmc variant.
-- vqmmc-supply           : phandle to the regulator device tree node, mentioned
-                           as the VCCQ/VDD_IO supply in the eMMC/SD specs.
-specific for ux500 variant:
-- st,sig-dir-dat0        : bus signal direction pin used for DAT[0].
-- st,sig-dir-dat2        : bus signal direction pin used for DAT[2].
-- st,sig-dir-dat31       : bus signal direction pin used for DAT[3] and DAT[1].
-- st,sig-dir-dat74       : bus signal direction pin used for DAT[4] to DAT[7].
-- st,sig-dir-cmd         : cmd signal direction pin used for CMD.
-- st,sig-pin-fbclk       : feedback clock signal pin used.
-
-specific for sdmmc variant:
-- st,sig-dir             : signal direction polarity used for cmd, dat0 dat123.
-- st,neg-edge            : data & command phase relation, generated on
-                           sd clock falling edge.
-- st,use-ckin            : use ckin pin from an external driver to sample
-                           the receive data (example: with voltage
-			   switch transceiver).
-
-Deprecated properties:
-- mmc-cap-mmc-highspeed  : indicates whether MMC is high speed capable.
-- mmc-cap-sd-highspeed   : indicates whether SD is high speed capable.
-
-Example:
-
-sdi0_per1@80126000 {
-	compatible = "arm,pl18x", "arm,primecell";
-	reg = <0x80126000 0x1000>;
-	interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>;
-
-	dmas = <&dma 29 0 0x2>, /* Logical - DevToMem */
-	       <&dma 29 0 0x0>; /* Logical - MemToDev */
-	dma-names = "rx", "tx";
-
-	clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>;
-	clock-names = "sdi", "apb_pclk";
-
-	max-frequency = <100000000>;
-	bus-width = <4>;
-	cap-sd-highspeed;
-	cap-mmc-highspeed;
-	cd-gpios  = <&gpio2 31 0x4>; // 95
-	st,sig-dir-dat0;
-	st,sig-dir-dat2;
-	st,sig-dir-cmd;
-	st,sig-pin-fbclk;
-
-	vmmc-supply = <&ab8500_ldo_aux3_reg>;
-	vqmmc-supply = <&vmmci>;
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdi0_default_mode>;
-	pinctrl-1 = <&sdi0_sleep_mode>;
-};