1 files changed, 72 insertions, 0 deletions
diff --git a/dts/Bindings/mmc/nvidia,tegra20-sdhci.txt b/dts/Bindings/mmc/nvidia,tegra20-sdhci.txt
index 9bce57862e..32b4b4e419 100644
--- a/dts/Bindings/mmc/nvidia,tegra20-sdhci.txt
+++ b/dts/Bindings/mmc/nvidia,tegra20-sdhci.txt
@@ -38,3 +38,75 @@ sdhci@c8000200 {
 	power-gpios = <&gpio 155 0>; /* gpio PT3 */
 	bus-width = <8>;
 };
+
+Optional properties for Tegra210 and Tegra186:
+- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage
+  configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8"
+  for controllers supporting multiple voltage levels. The order of names
+  should correspond to the pin configuration states in pinctrl-0 and
+  pinctrl-1.
+- nvidia,only-1-8-v : The presence of this property indicates that the
+  controller operates at a 1.8 V fixed I/O voltage.
+- nvidia,pad-autocal-pull-up-offset-3v3,
+  nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength
+  calibration offsets for 3.3 V signaling modes.
+- nvidia,pad-autocal-pull-up-offset-1v8,
+  nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength
+  calibration offsets for 1.8 V signaling modes.
+- nvidia,pad-autocal-pull-up-offset-3v3-timeout,
+  nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive
+  strength used as a fallback in case the automatic calibration times
+  out on a 3.3 V signaling mode.
+- nvidia,pad-autocal-pull-up-offset-1v8-timeout,
+  nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive
+  strength used as a fallback in case the automatic calibration times
+  out on a 1.8 V signaling mode.
+- nvidia,pad-autocal-pull-up-offset-sdr104,
+  nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength
+  calibration offsets for SDR104 mode.
+- nvidia,pad-autocal-pull-up-offset-hs400,
+  nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength
+  calibration offsets for HS400 mode.
+- nvidia,default-tap : Specify the default inbound sampling clock
+  trimmer value for non-tunable modes.
+- nvidia,default-trim : Specify the default outbound clock trimmer
+  value.
+- nvidia,dqs-trim : Specify DQS trim value for HS400 timing
+
+  Notes on the pad calibration pull up and pulldown offset values:
+    - The property values are drive codes which are programmed into the
+      PD_OFFSET and PU_OFFSET sections of the
+      SDHCI_TEGRA_AUTO_CAL_CONFIG register.
+    - A higher value corresponds to higher drive strength. Please refer
+      to the reference manual of the SoC for correct values.
+    - The SDR104 and HS400 timing specific values are used in
+      corresponding modes if specified.
+
+  Notes on tap and trim values:
+    - The values are used for compensating trace length differences
+      by adjusting the sampling point.
+    - The values are programmed to the Vendor Clock Control Register.
+      Please refer to the reference manual of the SoC for correct
+      values.
+    - The DQS trim values are only used on controllers which support
+      HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports
+      HS400.
+
+Example:
+sdhci@700b0000 {
+	compatible = "nvidia,tegra210-sdhci", "nvidia,tegra124-sdhci";
+	reg = <0x0 0x700b0000 0x0 0x200>;
+	interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&tegra_car TEGRA210_CLK_SDMMC1>;
+	clock-names = "sdhci";
+	resets = <&tegra_car 14>;
+	reset-names = "sdhci";
+	pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+	pinctrl-0 = <&sdmmc1_3v3>;
+	pinctrl-1 = <&sdmmc1_1v8>;
+	nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>;
+	nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>;
+	nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>;
+	nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>;
+	status = "disabled";
+};