summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/mtd/gpmc-nand.txt
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/mtd/gpmc-nand.txt')
-rw-r--r--dts/Bindings/mtd/gpmc-nand.txt47
1 files changed, 46 insertions, 1 deletions
diff --git a/dts/Bindings/mtd/gpmc-nand.txt b/dts/Bindings/mtd/gpmc-nand.txt
index 5e1f31b5ff..65f4f7c431 100644
--- a/dts/Bindings/mtd/gpmc-nand.txt
+++ b/dts/Bindings/mtd/gpmc-nand.txt
@@ -28,6 +28,8 @@ Optional properties:
"ham1" 1-bit Hamming ecc code
"bch4" 4-bit BCH ecc code
"bch8" 8-bit BCH ecc code
+ "bch16" 16-bit BCH ECC code
+ Refer below "How to select correct ECC scheme for your device ?"
- ti,nand-xfer-type: A string setting the data transfer type. One of:
@@ -43,7 +45,7 @@ Optional properties:
ELM hardware engines should specify this device node in .dtsi
Using ELM for ECC error correction frees some CPU cycles.
-For inline partiton table parsing (optional):
+For inline partition table parsing (optional):
- #address-cells: should be set to 1
- #size-cells: should be set to 1
@@ -90,3 +92,46 @@ Example for an AM33xx board:
};
};
+How to select correct ECC scheme for your device ?
+--------------------------------------------------
+Higher ECC scheme usually means better protection against bit-flips and
+increased system lifetime. However, selection of ECC scheme is dependent
+on various other factors also like;
+
+(1) support of built in hardware engines.
+ Some legacy OMAP SoC do not have ELM harware engine, so those SoC cannot
+ support ecc-schemes with hardware error-correction (BCHx_HW). However
+ such SoC can use ecc-schemes with software library for error-correction
+ (BCHx_HW_DETECTION_SW). The error correction capability with software
+ library remains equivalent to their hardware counter-part, but there is
+ slight CPU penalty when too many bit-flips are detected during reads.
+
+(2) Device parameters like OOBSIZE.
+ Other factor which governs the selection of ecc-scheme is oob-size.
+ Higher ECC schemes require more OOB/Spare area to store ECC syndrome,
+ so the device should have enough free bytes available its OOB/Spare
+ area to accomodate ECC for entire page. In general following expression
+ helps in determining if given device can accomodate ECC syndrome:
+ "2 + (PAGESIZE / 512) * ECC_BYTES" >= OOBSIZE"
+ where
+ OOBSIZE number of bytes in OOB/spare area
+ PAGESIZE number of bytes in main-area of device page
+ ECC_BYTES number of ECC bytes generated to protect
+ 512 bytes of data, which is:
+ '3' for HAM1_xx ecc schemes
+ '7' for BCH4_xx ecc schemes
+ '14' for BCH8_xx ecc schemes
+ '26' for BCH16_xx ecc schemes
+
+ Example(a): For a device with PAGESIZE = 2048 and OOBSIZE = 64 and
+ trying to use BCH16 (ECC_BYTES=26) ecc-scheme.
+ Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B
+ which is greater than capacity of NAND device (OOBSIZE=64)
+ Hence, BCH16 cannot be supported on given device. But it can
+ probably use lower ecc-schemes like BCH8.
+
+ Example(b): For a device with PAGESIZE = 2048 and OOBSIZE = 128 and
+ trying to use BCH16 (ECC_BYTES=26) ecc-scheme.
+ Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B
+ which can be accomodate in the OOB/Spare area of this device
+ (OOBSIZE=128). So this device can use BCH16 ecc-scheme.