1 files changed, 0 insertions, 157 deletions
diff --git a/dts/Bindings/mux/mux-controller.txt b/dts/Bindings/mux/mux-controller.txt
deleted file mode 100644
index 4f47e4bd2f..0000000000
--- a/dts/Bindings/mux/mux-controller.txt
+++ /dev/null
@@ -1,157 +0,0 @@
-Common multiplexer controller bindings
-======================================
-
-A multiplexer (or mux) controller will have one, or several, consumer devices
-that uses the mux controller. Thus, a mux controller can possibly control
-several parallel multiplexers. Presumably there will be at least one
-multiplexer needed by each consumer, but a single mux controller can of course
-control several multiplexers for a single consumer.
-
-A mux controller provides a number of states to its consumers, and the state
-space is a simple zero-based enumeration. I.e. 0-1 for a 2-way multiplexer,
-0-7 for an 8-way multiplexer, etc.
-
-
-Consumers
----------
-
-Mux controller consumers should specify a list of mux controllers that they
-want to use with a property containing a 'mux-ctrl-list':
-
-	mux-ctrl-list ::= <single-mux-ctrl> [mux-ctrl-list]
-	single-mux-ctrl ::= <mux-ctrl-phandle> [mux-ctrl-specifier]
-	mux-ctrl-phandle : phandle to mux controller node
-	mux-ctrl-specifier : array of #mux-control-cells specifying the
-			     given mux controller (controller specific)
-
-Mux controller properties should be named "mux-controls". The exact meaning of
-each mux controller property must be documented in the device tree binding for
-each consumer. An optional property "mux-control-names" may contain a list of
-strings to label each of the mux controllers listed in the "mux-controls"
-property.
-
-Drivers for devices that use more than a single mux controller can use the
-"mux-control-names" property to map the name of the requested mux controller
-to an index into the list given by the "mux-controls" property.
-
-mux-ctrl-specifier typically encodes the chip-relative mux controller number.
-If the mux controller chip only provides a single mux controller, the
-mux-ctrl-specifier can typically be left out.
-
-Example:
-
-	/* One consumer of a 2-way mux controller (one GPIO-line) */
-	mux: mux-controller {
-		compatible = "gpio-mux";
-		#mux-control-cells = <0>;
-
-		mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>;
-	};
-
-	adc-mux {
-		compatible = "io-channel-mux";
-		io-channels = <&adc 0>;
-		io-channel-names = "parent";
-
-		mux-controls = <&mux>;
-		mux-control-names = "adc";
-
-		channels = "sync", "in";
-	};
-
-Note that in the example above, specifying the "mux-control-names" is redundant
-because there is only one mux controller in the list. However, if the driver
-for the consumer node in fact asks for a named mux controller, that name is of
-course still required.
-
-	/*
-	 * Two consumers (one for an ADC line and one for an i2c bus) of
-	 * parallel 4-way multiplexers controlled by the same two GPIO-lines.
-	 */
-	mux: mux-controller {
-		compatible = "gpio-mux";
-		#mux-control-cells = <0>;
-
-		mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
-			    <&pioA 1 GPIO_ACTIVE_HIGH>;
-	};
-
-	adc-mux {
-		compatible = "io-channel-mux";
-		io-channels = <&adc 0>;
-		io-channel-names = "parent";
-
-		mux-controls = <&mux>;
-
-		channels = "sync-1", "in", "out", "sync-2";
-	};
-
-	i2c-mux {
-		compatible = "i2c-mux";
-		i2c-parent = <&i2c1>;
-
-		mux-controls = <&mux>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			ssd1307: oled@3c {
-				/* ... */
-			};
-		};
-
-		i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			pca9555: pca9555@20 {
-				/* ... */
-			};
-		};
-	};
-
-
-Mux controller nodes
---------------------
-
-Mux controller nodes must specify the number of cells used for the
-specifier using the '#mux-control-cells' property.
-
-Optionally, mux controller nodes can also specify the state the mux should
-have when it is idle. The idle-state property is used for this. If the
-idle-state is not present, the mux controller is typically left as is when
-it is idle. For multiplexer chips that expose several mux controllers, the
-idle-state property is an array with one idle state for each mux controller.
-
-The special value (-1) may be used to indicate that the mux should be left
-as is when it is idle. This is the default, but can still be useful for
-mux controller chips with more than one mux controller, particularly when
-there is a need to "step past" a mux controller and set some other idle
-state for a mux controller with a higher index.
-
-Some mux controllers have the ability to disconnect the input/output of the
-multiplexer. Using this disconnected high-impedance state as the idle state
-is indicated with idle state (-2).
-
-These constants are available in
-
-      #include <dt-bindings/mux/mux.h>
-
-as MUX_IDLE_AS_IS (-1) and MUX_IDLE_DISCONNECT (-2).
-
-An example mux controller node look like this (the adg972a chip is a triple
-4-way multiplexer):
-
-	mux: mux-controller@50 {
-		compatible = "adi,adg792a";
-		reg = <0x50>;
-		#mux-control-cells = <1>;
-
-		idle-state = <MUX_IDLE_DISCONNECT MUX_IDLE_AS_IS 2>;
-	};