diff options
Diffstat (limited to 'dts/Bindings/net/dsa/qca8k.yaml')
| -rw-r--r-- | dts/Bindings/net/dsa/qca8k.yaml | 321 |
1 files changed, 321 insertions, 0 deletions
diff --git a/dts/Bindings/net/dsa/qca8k.yaml b/dts/Bindings/net/dsa/qca8k.yaml new file mode 100644 index 0000000000..167398ab25 --- /dev/null +++ b/dts/Bindings/net/dsa/qca8k.yaml @@ -0,0 +1,321 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/qca8k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Atheros QCA83xx switch family + +maintainers: + - John Crispin <john@phrozen.org> + +description: + If the QCA8K switch is connect to an SoC's external mdio-bus, each subnode + describing a port needs to have a valid phandle referencing the internal PHY + it is connected to. This is because there is no N:N mapping of port and PHY + ID. To declare the internal mdio-bus configuration, declare an MDIO node in + the switch node and declare the phandle for the port, referencing the internal + PHY it is connected to. In this config, an internal mdio-bus is registered and + the MDIO master is used for communication. Mixed external and internal + mdio-bus configurations are not supported by the hardware. + Each phy has at most 3 LEDs connected and can be declared + using the standard LEDs structure. + +properties: + compatible: + oneOf: + - enum: + - qca,qca8327 + - qca,qca8328 + - qca,qca8334 + - qca,qca8337 + description: | + qca,qca8328: referenced as AR8328(N)-AK1(A/B) QFN 176 pin package + qca,qca8327: referenced as AR8327(N)-AL1A DR-QFN 148 pin package + qca,qca8334: referenced as QCA8334-AL3C QFN 88 pin package + qca,qca8337: referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package + + reg: + maxItems: 1 + + reset-gpios: + description: + GPIO to be used to reset the whole device + maxItems: 1 + + qca,ignore-power-on-sel: + $ref: /schemas/types.yaml#/definitions/flag + description: + Ignore power-on pin strapping to configure LED open-drain or EEPROM + presence. This is needed for devices with incorrect configuration or when + the OEM has decided not to use pin strapping and falls back to SW regs. + + qca,led-open-drain: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set LEDs to open-drain mode. This requires the qca,ignore-power-on-sel to + be set, otherwise the driver will fail at probe. This is required if the + OEM does not use pin strapping to set this mode and prefers to set it + using SW regs. The pin strappings related to LED open-drain mode are + B68 on the QCA832x and B49 on the QCA833x. + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Qca8k switch have an internal mdio to access switch port. + If this is not present, the legacy mapping is used and the + internal mdio access is used. + With the legacy mapping the reg corresponding to the internal + mdio is the switch reg with an offset of -1. + +$ref: dsa.yaml# + +patternProperties: + "^(ethernet-)?ports$": + type: object + additionalProperties: true + patternProperties: + "^(ethernet-)?port@[0-6]$": + type: object + description: Ethernet switch ports + + $ref: dsa-port.yaml# + + properties: + qca,sgmii-rxclk-falling-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set the receive clock phase to falling edge. Mostly commonly used on + the QCA8327 with CPU port 0 set to SGMII. + + qca,sgmii-txclk-falling-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: + Set the transmit clock phase to falling edge. + + qca,sgmii-enable-pll: + $ref: /schemas/types.yaml#/definitions/flag + description: + For SGMII CPU port, explicitly enable PLL, TX and RX chain along with + Signal Detection. On the QCA8327 this should not be enabled, otherwise + the SGMII port will not initialize. When used on the QCA8337, revision 3 + or greater, a warning will be displayed. When the CPU port is set to + SGMII on the QCA8337, it is advised to set this unless a communication + issue is observed. + + unevaluatedProperties: false + +oneOf: + - required: + - ports + - required: + - ethernet-ports + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/leds/common.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + external_phy_port1: ethernet-phy@0 { + reg = <0>; + }; + + external_phy_port2: ethernet-phy@1 { + reg = <1>; + }; + + external_phy_port3: ethernet-phy@2 { + reg = <2>; + }; + + external_phy_port4: ethernet-phy@3 { + reg = <3>; + }; + + external_phy_port5: ethernet-phy@4 { + reg = <4>; + }; + + switch@10 { + compatible = "qca,qca8337"; + reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&external_phy_port1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&external_phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&external_phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-handle = <&external_phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-handle = <&external_phy_port5>; + }; + }; + }; + }; + - | + #include <dt-bindings/gpio/gpio.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@10 { + compatible = "qca,qca8337"; + reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port1>; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + color = <LED_COLOR_ID_WHITE>; + function = LED_FUNCTION_LAN; + default-state = "keep"; + }; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_AMBER>; + function = LED_FUNCTION_LAN; + default-state = "keep"; + }; + }; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-mode = "internal"; + phy-handle = <&internal_phy_port5>; + }; + + port@6 { + reg = <0>; + ethernet = <&gmac1>; + phy-mode = "sgmii"; + + qca,sgmii-rxclk-falling-edge; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + internal_phy_port1: ethernet-phy@0 { + reg = <0>; + }; + + internal_phy_port2: ethernet-phy@1 { + reg = <1>; + }; + + internal_phy_port3: ethernet-phy@2 { + reg = <2>; + }; + + internal_phy_port4: ethernet-phy@3 { + reg = <3>; + }; + + internal_phy_port5: ethernet-phy@4 { + reg = <4>; + }; + }; + }; + }; |