diff options
Diffstat (limited to 'dts/Bindings/net/dsa')
23 files changed, 1599 insertions, 725 deletions
diff --git a/dts/Bindings/net/dsa/ar9331.txt b/dts/Bindings/net/dsa/ar9331.txt deleted file mode 100644 index 320607cbbb..0000000000 --- a/dts/Bindings/net/dsa/ar9331.txt +++ /dev/null @@ -1,148 +0,0 @@ -Atheros AR9331 built-in switch -============================= - -It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal -MDIO bus. All PHYs are built-in as well. - -Required properties: - - - compatible: should be: "qca,ar9331-switch" - - reg: Address on the MII bus for the switch. - - resets : Must contain an entry for each entry in reset-names. - - reset-names : Must include the following entries: "switch" - - interrupt-parent: Phandle to the parent interrupt controller - - interrupts: IRQ line for the switch - - interrupt-controller: Indicates the switch is itself an interrupt - controller. This is used for the PHY interrupts. - - #interrupt-cells: must be 1 - - mdio: Container of PHY and devices on the switches MDIO bus. - -See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional -required and optional properties. -Examples: - -eth0: ethernet@19000000 { - compatible = "qca,ar9330-eth"; - reg = <0x19000000 0x200>; - interrupts = <4>; - - resets = <&rst 9>, <&rst 22>; - reset-names = "mac", "mdio"; - clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>; - clock-names = "eth", "mdio"; - - phy-mode = "mii"; - phy-handle = <&phy_port4>; -}; - -eth1: ethernet@1a000000 { - compatible = "qca,ar9330-eth"; - reg = <0x1a000000 0x200>; - interrupts = <5>; - resets = <&rst 13>, <&rst 23>; - reset-names = "mac", "mdio"; - clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>; - clock-names = "eth", "mdio"; - - phy-mode = "gmii"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - switch10: switch@10 { - #address-cells = <1>; - #size-cells = <0>; - - compatible = "qca,ar9331-switch"; - reg = <0x10>; - resets = <&rst 8>; - reset-names = "switch"; - - interrupt-parent = <&miscintc>; - interrupts = <12>; - - interrupt-controller; - #interrupt-cells = <1>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - switch_port0: port@0 { - reg = <0x0>; - label = "cpu"; - ethernet = <ð1>; - - phy-mode = "gmii"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - switch_port1: port@1 { - reg = <0x1>; - phy-handle = <&phy_port0>; - phy-mode = "internal"; - }; - - switch_port2: port@2 { - reg = <0x2>; - phy-handle = <&phy_port1>; - phy-mode = "internal"; - }; - - switch_port3: port@3 { - reg = <0x3>; - phy-handle = <&phy_port2>; - phy-mode = "internal"; - }; - - switch_port4: port@4 { - reg = <0x4>; - phy-handle = <&phy_port3>; - phy-mode = "internal"; - }; - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - interrupt-parent = <&switch10>; - - phy_port0: phy@0 { - reg = <0x0>; - interrupts = <0>; - }; - - phy_port1: phy@1 { - reg = <0x1>; - interrupts = <0>; - }; - - phy_port2: phy@2 { - reg = <0x2>; - interrupts = <0>; - }; - - phy_port3: phy@3 { - reg = <0x3>; - interrupts = <0>; - }; - - phy_port4: phy@4 { - reg = <0x4>; - interrupts = <0>; - }; - }; - }; - }; -}; diff --git a/dts/Bindings/net/dsa/arrow,xrs700x.yaml b/dts/Bindings/net/dsa/arrow,xrs700x.yaml index 3f01b65f3b..9565a74021 100644 --- a/dts/Bindings/net/dsa/arrow,xrs700x.yaml +++ b/dts/Bindings/net/dsa/arrow,xrs700x.yaml @@ -4,10 +4,10 @@ $id: http://devicetree.org/schemas/net/dsa/arrow,xrs700x.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Arrow SpeedChips XRS7000 Series Switch Device Tree Bindings +title: Arrow SpeedChips XRS7000 Series Switch allOf: - - $ref: dsa.yaml# + - $ref: dsa.yaml#/$defs/ethernet-ports maintainers: - George McCollister <george.mccollister@gmail.com> @@ -61,8 +61,9 @@ examples: }; ethernet-port@3 { reg = <3>; - label = "cpu"; ethernet = <&fec1>; + phy-mode = "rgmii-id"; + fixed-link { speed = <1000>; full-duplex; diff --git a/dts/Bindings/net/dsa/brcm,b53.yaml b/dts/Bindings/net/dsa/brcm,b53.yaml index 23114d691d..4c78c54634 100644 --- a/dts/Bindings/net/dsa/brcm,b53.yaml +++ b/dts/Bindings/net/dsa/brcm,b53.yaml @@ -19,6 +19,7 @@ properties: - const: brcm,bcm53115 - const: brcm,bcm53125 - const: brcm,bcm53128 + - const: brcm,bcm53134 - const: brcm,bcm5365 - const: brcm,bcm5395 - const: brcm,bcm5389 @@ -57,8 +58,11 @@ properties: - items: - enum: - brcm,bcm3384-switch + - brcm,bcm6318-switch - brcm,bcm6328-switch + - brcm,bcm6362-switch - brcm,bcm6368-switch + - brcm,bcm63268-switch - const: brcm,bcm63xx-switch required: @@ -66,7 +70,7 @@ required: - reg allOf: - - $ref: dsa.yaml# + - $ref: dsa.yaml#/$defs/ethernet-ports - if: properties: compatible: @@ -169,7 +173,6 @@ examples: port@8 { reg = <8>; - label = "cpu"; phy-mode = "rgmii-txid"; ethernet = <ð0>; fixed-link { @@ -252,8 +255,9 @@ examples: port@8 { ethernet = <&amac2>; - label = "cpu"; reg = <8>; + phy-mode = "internal"; + fixed-link { speed = <1000>; full-duplex; diff --git a/dts/Bindings/net/dsa/brcm,sf2.yaml b/dts/Bindings/net/dsa/brcm,sf2.yaml index d159ac78ce..f21bdd0f40 100644 --- a/dts/Bindings/net/dsa/brcm,sf2.yaml +++ b/dts/Bindings/net/dsa/brcm,sf2.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/dsa/brcm,sf2.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Broadcom Starfighter 2 integrated swich +title: Broadcom Starfighter 2 integrated switch maintainers: - Florian Fainelli <f.fainelli@gmail.com> @@ -76,29 +76,27 @@ properties: supports reporting the number of packets in-flight in a switch queue type: boolean - "#address-cells": - const: 1 - - "#size-cells": - const: 0 - ports: type: object + additionalProperties: true + + patternProperties: + '^port@[0-9a-f]$': + $ref: dsa-port.yaml# + unevaluatedProperties: false - properties: - brcm,use-bcm-hdr: - description: if present, indicates that the switch port has Broadcom - tags enabled (per-packet metadata) - type: boolean + properties: + brcm,use-bcm-hdr: + description: if present, indicates that the switch port has Broadcom + tags enabled (per-packet metadata) + type: boolean required: - reg - interrupts - - "#address-cells" - - "#size-cells" allOf: - - $ref: "dsa.yaml#" + - $ref: dsa.yaml# - if: properties: compatible: @@ -140,8 +138,6 @@ examples: - | switch@f0b00000 { compatible = "brcm,bcm7445-switch-v4.0"; - #address-cells = <1>; - #size-cells = <0>; reg = <0xf0b00000 0x40000>, <0xf0b40000 0x110>, <0xf0b40340 0x30>, diff --git a/dts/Bindings/net/dsa/dsa-port.yaml b/dts/Bindings/net/dsa/dsa-port.yaml index 09317e16cb..4801204699 100644 --- a/dts/Bindings/net/dsa/dsa-port.yaml +++ b/dts/Bindings/net/dsa/dsa-port.yaml @@ -4,22 +4,24 @@ $id: http://devicetree.org/schemas/net/dsa/dsa-port.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Ethernet Switch port Device Tree Bindings +title: Generic DSA Switch Port maintainers: - Andrew Lunn <andrew@lunn.ch> - Florian Fainelli <f.fainelli@gmail.com> - - Vivien Didelot <vivien.didelot@gmail.com> + - Vladimir Oltean <olteanv@gmail.com> description: - Ethernet switch port Description + A DSA switch port is a component of a switch that manages one MAC, and can + pass Ethernet frames. It can act as a stanadard Ethernet switch port, or have + DSA-specific functionality. -allOf: - - $ref: /schemas/net/ethernet-controller.yaml# +$ref: /schemas/net/ethernet-switch-port.yaml# properties: reg: - description: Port number + items: + - description: Port number label: description: @@ -57,24 +59,22 @@ properties: - rtl8_4t - seville - phy-handle: true - - phy-mode: true - - fixed-link: true - - mac-address: true - - sfp: true - - managed: true - - rx-internal-delay-ps: true - - tx-internal-delay-ps: true - -required: - - reg +# CPU and DSA ports must have phylink-compatible link descriptions +if: + oneOf: + - required: [ ethernet ] + - required: [ link ] +then: + allOf: + - required: + - phy-mode + - oneOf: + - required: + - fixed-link + - required: + - phy-handle + - required: + - managed additionalProperties: true diff --git a/dts/Bindings/net/dsa/dsa.yaml b/dts/Bindings/net/dsa/dsa.yaml index b9d48e357e..2abd036578 100644 --- a/dts/Bindings/net/dsa/dsa.yaml +++ b/dts/Bindings/net/dsa/dsa.yaml @@ -4,12 +4,12 @@ $id: http://devicetree.org/schemas/net/dsa/dsa.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Ethernet Switch Device Tree Bindings +title: Ethernet Switch maintainers: - Andrew Lunn <andrew@lunn.ch> - Florian Fainelli <f.fainelli@gmail.com> - - Vivien Didelot <vivien.didelot@gmail.com> + - Vladimir Oltean <olteanv@gmail.com> description: This binding represents Ethernet Switches which have a dedicated CPU @@ -18,10 +18,9 @@ description: select: false -properties: - $nodename: - pattern: "^(ethernet-)?switch(@.*)?$" +$ref: /schemas/net/ethernet-switch.yaml# +properties: dsa,member: minItems: 2 maxItems: 2 @@ -32,23 +31,20 @@ properties: (single device hanging off a CPU port) must not specify this property $ref: /schemas/types.yaml#/definitions/uint32-array -patternProperties: - "^(ethernet-)?ports$": - type: object - properties: - '#address-cells': - const: 1 - '#size-cells': - const: 0 - - patternProperties: - "^(ethernet-)?port@[0-9]+$": - type: object - description: Ethernet switch ports +additionalProperties: true - $ref: dsa-port.yaml# +$defs: + ethernet-ports: + description: A DSA switch without any extra port properties + $ref: '#' - unevaluatedProperties: false + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-9a-f]+$": + description: Ethernet switch ports + $ref: dsa-port.yaml# + unevaluatedProperties: false oneOf: - required: @@ -56,6 +52,4 @@ oneOf: - required: - ethernet-ports -additionalProperties: true - ... diff --git a/dts/Bindings/net/dsa/hirschmann,hellcreek.yaml b/dts/Bindings/net/dsa/hirschmann,hellcreek.yaml index 2286837731..4021b054f6 100644 --- a/dts/Bindings/net/dsa/hirschmann,hellcreek.yaml +++ b/dts/Bindings/net/dsa/hirschmann,hellcreek.yaml @@ -4,15 +4,15 @@ $id: http://devicetree.org/schemas/net/dsa/hirschmann,hellcreek.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Hirschmann Hellcreek TSN Switch Device Tree Bindings +title: Hirschmann Hellcreek TSN Switch allOf: - - $ref: dsa.yaml# + - $ref: dsa.yaml#/$defs/ethernet-ports maintainers: - Andrew Lunn <andrew@lunn.ch> - Florian Fainelli <f.fainelli@gmail.com> - - Vivien Didelot <vivien.didelot@gmail.com> + - Vladimir Oltean <olteanv@gmail.com> - Kurt Kanzenbach <kurt@linutronix.de> description: @@ -91,8 +91,13 @@ examples: port@0 { reg = <0>; - label = "cpu"; ethernet = <&gmac0>; + phy-mode = "mii"; + + fixed-link { + speed = <100>; + full-duplex; + }; }; port@2 { diff --git a/dts/Bindings/net/dsa/lan9303.txt b/dts/Bindings/net/dsa/lan9303.txt index 464d6bf876..46a732087f 100644 --- a/dts/Bindings/net/dsa/lan9303.txt +++ b/dts/Bindings/net/dsa/lan9303.txt @@ -46,7 +46,6 @@ I2C managed mode: port@0 { /* RMII fixed link to master */ reg = <0>; - label = "cpu"; ethernet = <&master>; }; @@ -83,7 +82,6 @@ MDIO managed mode: port@0 { reg = <0>; - label = "cpu"; ethernet = <&master>; }; diff --git a/dts/Bindings/net/dsa/lantiq-gswip.txt b/dts/Bindings/net/dsa/lantiq-gswip.txt index e3829d3e48..8bb1eff21c 100644 --- a/dts/Bindings/net/dsa/lantiq-gswip.txt +++ b/dts/Bindings/net/dsa/lantiq-gswip.txt @@ -96,7 +96,6 @@ switch@e108000 { port@6 { reg = <0x6>; - label = "cpu"; ethernet = <ð0>; }; }; diff --git a/dts/Bindings/net/dsa/marvell,mv88e6060.yaml b/dts/Bindings/net/dsa/marvell,mv88e6060.yaml new file mode 100644 index 0000000000..4f1adf0043 --- /dev/null +++ b/dts/Bindings/net/dsa/marvell,mv88e6060.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6060.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MV88E6060 DSA switch + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + +description: + The Marvell MV88E6060 switch has been produced and sold by Marvell + since at least 2008. The switch has one pin ADDR4 that controls the + MDIO address of the switch to be 0x10 or 0x00, and on the MDIO bus + connected to the switch, the PHYs inside the switch appear as + independent devices on address 0x00-0x04 or 0x10-0x14, so in difference + from many other DSA switches this switch does not have an internal + MDIO bus for the PHY devices. + +properties: + compatible: + const: marvell,mv88e6060 + description: + The MV88E6060 is the oldest Marvell DSA switch product, and + as such a bit limited in features compared to later hardware. + + reg: + maxItems: 1 + + reset-gpios: + description: + GPIO to be used to reset the whole device + maxItems: 1 + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@16 { + compatible = "marvell,mv88e6060"; + reg = <16>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-port@0 { + reg = <0>; + label = "lan1"; + }; + ethernet-port@1 { + reg = <1>; + label = "lan2"; + }; + ethernet-port@2 { + reg = <2>; + label = "lan3"; + }; + ethernet-port@3 { + reg = <3>; + label = "lan4"; + }; + ethernet-port@5 { + reg = <5>; + phy-mode = "rev-mii"; + ethernet = <ðc>; + fixed-link { + speed = <100>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/dts/Bindings/net/dsa/marvell,mv88e6xxx.yaml b/dts/Bindings/net/dsa/marvell,mv88e6xxx.yaml new file mode 100644 index 0000000000..19f15bdd1c --- /dev/null +++ b/dts/Bindings/net/dsa/marvell,mv88e6xxx.yaml @@ -0,0 +1,337 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MV88E6xxx DSA switch family + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + +description: + The Marvell MV88E6xxx switch series has been produced and sold + by Marvell since at least 2008. The switch has a few compatibles which + just indicate the base address of the switch, then operating systems + can investigate switch ID registers to find out which actual version + of the switch it is dealing with. + +properties: + compatible: + oneOf: + - enum: + - marvell,mv88e6085 + - marvell,mv88e6190 + - marvell,mv88e6250 + description: | + marvell,mv88e6085: This switch uses base address 0x10. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6085" should be + specified. This includes the following list of MV88Exxxx switches: + 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176, + 6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352 + marvell,mv88e6190: This switch uses base address 0x00. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6190" should be + specified. This includes the following list of MV88Exxxx switches: + 6190, 6190X, 6191, 6290, 6361, 6390, 6390X + marvell,mv88e6250: This switch uses base address 0x08 or 0x18. + This switch and its siblings will be autodetected from + ID registers found in the switch, so only "marvell,mv88e6250" should be + specified. This includes the following list of MV88Exxxx switches: + 6220, 6250 + - items: + - const: marvell,turris-mox-mv88e6085 + - const: marvell,mv88e6085 + - items: + - const: marvell,turris-mox-mv88e6190 + - const: marvell,mv88e6190 + + reg: + maxItems: 1 + + eeprom-length: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Set to the length of an EEPROM connected to the switch. Must be + set if the switch can not detect the presence and/or size of a connected + EEPROM, otherwise optional. + + reset-gpios: + description: + GPIO to be used to reset the whole device + maxItems: 1 + + interrupts: + description: The switch provides an external interrupt line, but it is + not always used by target systems. + maxItems: 1 + + interrupt-controller: + description: The switch has an internal interrupt controller used by + the different sub-blocks. + + '#interrupt-cells': + description: The internal interrupt controller only supports triggering + on active high level interrupts so the second cell must alway be set to + IRQ_TYPE_LEVEL_HIGH. + const: 2 + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Marvell MV88E6xxx switches have an varying combination of + internal and external MDIO buses, in some cases a combined bus that + can be used both internally and externally. This node is for the + primary bus, used internally and sometimes also externally. + + mdio-external: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + description: Marvell MV88E6xxx switches that have a separate external + MDIO bus use this port to access external components on the MDIO bus. + + properties: + compatible: + const: marvell,mv88e6xxx-mdio-external + + required: + - compatible + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + sw_phy0: ethernet-phy@0 { + reg = <0x0>; + }; + + sw_phy1: ethernet-phy@1 { + reg = <0x1>; + }; + + sw_phy2: ethernet-phy@2 { + reg = <0x2>; + }; + + sw_phy3: ethernet-phy@3 { + reg = <0x3>; + }; + }; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-port@0 { + reg = <0>; + label = "lan4"; + phy-handle = <&sw_phy0>; + phy-mode = "internal"; + }; + + ethernet-port@1 { + reg = <1>; + label = "lan3"; + phy-handle = <&sw_phy1>; + phy-mode = "internal"; + }; + + ethernet-port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&sw_phy2>; + phy-mode = "internal"; + }; + + ethernet-port@3 { + reg = <3>; + label = "lan1"; + phy-handle = <&sw_phy3>; + phy-mode = "internal"; + }; + + ethernet-port@5 { + reg = <5>; + ethernet = <&fec>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-switch@0 { + compatible = "marvell,mv88e6190"; + #interrupt-cells = <2>; + interrupt-controller; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&switch_interrupt_pins>; + pinctrl-names = "default"; + reg = <0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0phy1: ethernet-phy@1 { + reg = <0x1>; + }; + + switch0phy2: ethernet-phy@2 { + reg = <0x2>; + }; + + switch0phy3: ethernet-phy@3 { + reg = <0x3>; + }; + + switch0phy4: ethernet-phy@4 { + reg = <0x4>; + }; + + switch0phy5: ethernet-phy@5 { + reg = <0x5>; + }; + + switch0phy6: ethernet-phy@6 { + reg = <0x6>; + }; + + switch0phy7: ethernet-phy@7 { + reg = <0x7>; + }; + + switch0phy8: ethernet-phy@8 { + reg = <0x8>; + }; + }; + + mdio-external { + compatible = "marvell,mv88e6xxx-mdio-external"; + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@b { + reg = <0xb>; + compatible = "ethernet-phy-ieee802.3-c45"; + }; + + phy2: ethernet-phy@c { + reg = <0xc>; + compatible = "ethernet-phy-ieee802.3-c45"; + }; + }; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-port@0 { + ethernet = <ð0>; + phy-mode = "rgmii"; + reg = <0>; + + fixed-link { + full-duplex; + pause; + speed = <1000>; + }; + }; + + ethernet-port@1 { + label = "lan1"; + phy-handle = <&switch0phy1>; + reg = <1>; + }; + + ethernet-port@2 { + label = "lan2"; + phy-handle = <&switch0phy2>; + reg = <2>; + }; + + ethernet-port@3 { + label = "lan3"; + phy-handle = <&switch0phy3>; + reg = <3>; + }; + + ethernet-port@4 { + label = "lan4"; + phy-handle = <&switch0phy4>; + reg = <4>; + }; + + ethernet-port@5 { + label = "lan5"; + phy-handle = <&switch0phy5>; + reg = <5>; + }; + + ethernet-port@6 { + label = "lan6"; + phy-handle = <&switch0phy6>; + reg = <6>; + }; + + ethernet-port@7 { + label = "lan7"; + phy-handle = <&switch0phy7>; + reg = <7>; + }; + + ethernet-port@8 { + label = "lan8"; + phy-handle = <&switch0phy8>; + reg = <8>; + }; + + ethernet-port@9 { + /* 88X3310P external phy */ + label = "lan9"; + phy-handle = <&phy1>; + phy-mode = "xaui"; + reg = <9>; + }; + + ethernet-port@a { + /* 88X3310P external phy */ + label = "lan10"; + phy-handle = <&phy2>; + phy-mode = "xaui"; + reg = <0xa>; + }; + }; + }; + }; diff --git a/dts/Bindings/net/dsa/marvell.txt b/dts/Bindings/net/dsa/marvell.txt deleted file mode 100644 index 2363b41241..0000000000 --- a/dts/Bindings/net/dsa/marvell.txt +++ /dev/null @@ -1,109 +0,0 @@ -Marvell DSA Switch Device Tree Bindings ---------------------------------------- - -WARNING: This binding is currently unstable. Do not program it into a -FLASH never to be changed again. Once this binding is stable, this -warning will be removed. - -If you need a stable binding, use the old dsa.txt binding. - -Marvell Switches are MDIO devices. The following properties should be -placed as a child node of an mdio device. - -The properties described here are those specific to Marvell devices. -Additional required and optional properties can be found in dsa.txt. - -The compatibility string is used only to find an identification register, -which is at a different MDIO base address in different switch families. -- "marvell,mv88e6085" : Switch has base address 0x10. Use with models: - 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, - 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321, - 6341, 6350, 6351, 6352 -- "marvell,mv88e6190" : Switch has base address 0x00. Use with models: - 6190, 6190X, 6191, 6290, 6390, 6390X -- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model: - 6220, 6250 - -Required properties: -- compatible : Should be one of "marvell,mv88e6085", - "marvell,mv88e6190" or "marvell,mv88e6250" as - indicated above -- reg : Address on the MII bus for the switch. - -Optional properties: - -- reset-gpios : Should be a gpio specifier for a reset line -- interrupts : Interrupt from the switch -- interrupt-controller : Indicates the switch is itself an interrupt - controller. This is used for the PHY interrupts. -#interrupt-cells = <2> : Controller uses two cells, number and flag -- eeprom-length : Set to the length of an EEPROM connected to the - switch. Must be set if the switch can not detect - the presence and/or size of a connected EEPROM, - otherwise optional. -- mdio : Container of PHY and devices on the switches MDIO - bus. -- mdio? : Container of PHYs and devices on the external MDIO - bus. The node must contains a compatible string of - "marvell,mv88e6xxx-mdio-external" - -Example: - - mdio { - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&gpio0>; - interrupts = <27 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - - switch0: switch@0 { - compatible = "marvell,mv88e6085"; - reg = <0>; - reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - switch1phy0: switch1phy0@0 { - reg = <0>; - interrupt-parent = <&switch0>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; - }; - }; - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&gpio0>; - interrupts = <27 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - - switch0: switch@0 { - compatible = "marvell,mv88e6190"; - reg = <0>; - reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - switch1phy0: switch1phy0@0 { - reg = <0>; - interrupt-parent = <&switch0>; - interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; - }; - }; - - mdio1 { - compatible = "marvell,mv88e6xxx-mdio-external"; - #address-cells = <1>; - #size-cells = <0>; - switch1phy9: switch1phy0@9 { - reg = <9>; - }; - }; - }; - }; diff --git a/dts/Bindings/net/dsa/mediatek,mt7530.yaml b/dts/Bindings/net/dsa/mediatek,mt7530.yaml index 17ab6c69ec..1c2444121e 100644 --- a/dts/Bindings/net/dsa/mediatek,mt7530.yaml +++ b/dts/Bindings/net/dsa/mediatek,mt7530.yaml @@ -4,67 +4,93 @@ $id: http://devicetree.org/schemas/net/dsa/mediatek,mt7530.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT7530 Ethernet switch +title: Mediatek MT7530 and MT7531 Ethernet Switches maintainers: - - Sean Wang <sean.wang@mediatek.com> + - Arınç ÃœNAL <arinc.unal@arinc9.com> - Landen Chao <Landen.Chao@mediatek.com> - DENG Qingfang <dqfext@gmail.com> + - Sean Wang <sean.wang@mediatek.com> + - Daniel Golle <daniel@makrotopia.org> description: | - Port 5 of mt7530 and mt7621 switch is muxed between: - 1. GMAC5: GMAC5 can interface with another external MAC or PHY. - 2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC - of the SOC. Used in many setups where port 0/4 becomes the WAN port. - Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to - GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not - connected to external component! - - Port 5 modes/configurations: - 1. Port 5 is disabled and isolated: An external phy can interface to the 2nd - GMAC of the SOC. - In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd - GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC! - 2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC. - It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode - and RGMII delay. - 3. Port 5 is muxed to GMAC5 and can interface to an external phy. - Port 5 becomes an extra switch port. - Only works on platform where external phy TX<->RX lines are swapped. - Like in the Ubiquiti ER-X-SFP. - 4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port. - Currently a 2nd CPU port is not supported by DSA code. - - Depending on how the external PHY is wired: - 1. normal: The PHY can only connect to 2nd GMAC but not to the switch - 2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as - a ethernet port. But can't interface to the 2nd GMAC. - - Based on the DT the port 5 mode is configured. - - Driver tries to lookup the phy-handle of the 2nd GMAC of the master device. - When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2. - phy-mode must be set, see also example 2 below! - * mt7621: phy-mode = "rgmii-txid"; - * mt7623: phy-mode = "rgmii"; - - CPU-Ports need a phy-mode property: - Allowed values on mt7530 and mt7621: - - "rgmii" - - "trgmii" - On mt7531: - - "1000base-x" - - "2500base-x" - - "rgmii" - - "sgmii" + There are three versions of MT7530, standalone, in a multi-chip module and + built-into a SoC. + + MT7530 is a part of the multi-chip module in MT7620AN, MT7620DA, MT7620DAN, + MT7620NN, MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs. + + The MT7988 SoC comes with a built-in switch similar to MT7531 as well as four + Gigabit Ethernet PHYs. The switch registers are directly mapped into the SoC's + memory map rather than using MDIO. The switch got an internally connected 10G + CPU port and 4 user ports connected to the built-in Gigabit Ethernet PHYs. + + MT7530 in MT7620AN, MT7620DA, MT7620DAN and MT7620NN SoCs has got 10/100 PHYs + and the switch registers are directly mapped into SoC's memory map rather than + using MDIO. The DSA driver currently doesn't support MT7620 variants. + + There is only the standalone version of MT7531. + + Port 5 on MT7530 has got various ways of configuration: + + - Port 5 can be used as a CPU port. + + - PHY 0 or 4 of the switch can be muxed to gmac5 of the switch. Therefore, + the gmac of the SoC which is wired to port 5 can connect to the PHY. + This is usually used for connecting the wan port directly to the CPU to + achieve 2 Gbps routing in total. + + The driver looks up the reg on the ethernet-phy node, which the phy-handle + property on the gmac node refers to, to mux the specified phy. + + The driver requires the gmac of the SoC to have "mediatek,eth-mac" as the + compatible string and the reg must be 1. So, for now, only gmac1 of a + MediaTek SoC can benefit this. Banana Pi BPI-R2 suits this. + + For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function. + + Check out example 5. + + - For the multi-chip module MT7530, in case of an external phy wired to + gmac1 of the SoC, port 5 must not be enabled. + + In case of muxing PHY 0 or 4, the external phy must not be enabled. + + For the MT7621 SoCs, rgmii2 group must be claimed with rgmii2 function. + + Check out example 6. + + - Port 5 can be wired to an external phy. Port 5 becomes a DSA user port. + + For the multi-chip module MT7530, the external phy must be wired TX to TX + to gmac1 of the SoC for this to work. Ubiquiti EdgeRouter X SFP is wired + this way. + + For the multi-chip module MT7530, muxing PHY 0 or 4 won't work when the + external phy is connected TX to TX. + For the MT7621 SoCs, rgmii2 group must be claimed with gpio function. + + Check out example 7. properties: compatible: - enum: - - mediatek,mt7530 - - mediatek,mt7531 - - mediatek,mt7621 + oneOf: + - description: + Standalone MT7530 and multi-chip module MT7530 in MT7623AI SoC + const: mediatek,mt7530 + + - description: + Standalone MT7531 + const: mediatek,mt7531 + + - description: + Multi-chip module MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs + const: mediatek,mt7621 + + - description: + Built-in switch of the MT7988 SoC + const: mediatek,mt7988-switch reg: maxItems: 1 @@ -78,8 +104,15 @@ properties: gpio-controller: type: boolean - description: - if defined, MT7530's LED controller will run on GPIO mode. + description: | + If defined, LED controller of the MT7530 switch will run on GPIO mode. + + There are 15 controllable pins. + port 0 LED 0..2 as GPIO 0..2 + port 1 LED 0..2 as GPIO 3..5 + port 2 LED 0..2 as GPIO 6..8 + port 3 LED 0..2 as GPIO 9..11 + port 4 LED 0..2 as GPIO 12..14 "#interrupt-cells": const: 1 @@ -90,19 +123,23 @@ properties: maxItems: 1 io-supply: - description: + description: | Phandle to the regulator node necessary for the I/O power. - See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt - for details for the regulator setup on these boards. + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt for + details for the regulator setup on these boards. mediatek,mcm: type: boolean description: - if defined, indicates that either MT7530 is the part on multi-chip - module belong to MT7623A has or the remotely standalone chip as the - function MT7623N reference board provided for. + Used for MT7621AT, MT7621DAT, MT7621ST and MT7623AI SoCs which the MT7530 + switch is a part of the multi-chip module. reset-gpios: + description: | + GPIO to reset the switch. Use this if mediatek,mcm is not used. + This property is optional because some boards share the reset line with + other components which makes it impossible to probe the switch if the + reset line is used. maxItems: 1 reset-names: @@ -110,49 +147,104 @@ properties: resets: description: - Phandle pointing to the system reset controller with line index for - the ethsys. + Phandle pointing to the system reset controller with line index for the + ethsys. maxItems: 1 patternProperties: "^(ethernet-)?ports$": type: object + additionalProperties: true patternProperties: - "^(ethernet-)?port@[0-9]+$": + "^(ethernet-)?port@[0-6]$": type: object - description: Ethernet switch ports - - unevaluatedProperties: false + additionalProperties: true properties: reg: description: - Port address described must be 5 or 6 for CPU port and from 0 - to 5 for user ports. + Port address described must be 5 or 6 for CPU port and from 0 to 5 + for user ports. allOf: - - $ref: dsa-port.yaml# - if: - properties: - label: - items: - - const: cpu + required: [ ethernet ] then: - required: - - reg - - phy-mode + properties: + reg: + enum: + - 5 + - 6 required: - compatible - reg +$defs: + mt7530-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-6]$": + if: + required: [ ethernet ] + then: + if: + properties: + reg: + const: 5 + then: + properties: + phy-mode: + enum: + - gmii + - mii + - rgmii + else: + properties: + phy-mode: + enum: + - rgmii + - trgmii + + mt7531-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-6]$": + if: + required: [ ethernet ] + then: + if: + properties: + reg: + const: 5 + then: + properties: + phy-mode: + enum: + - 1000base-x + - 2500base-x + - rgmii + - sgmii + else: + properties: + phy-mode: + enum: + - 1000base-x + - 2500base-x + - sgmii + allOf: - - $ref: "dsa.yaml#" + - $ref: dsa.yaml#/$defs/ethernet-ports - if: required: - mediatek,mcm then: + properties: + reset-gpios: false + required: - resets - reset-names @@ -163,52 +255,150 @@ allOf: - if: properties: compatible: - items: - - const: mediatek,mt7530 + const: mediatek,mt7530 then: + $ref: "#/$defs/mt7530-dsa-port" required: - core-supply - io-supply + - if: + properties: + compatible: + const: mediatek,mt7531 + then: + $ref: "#/$defs/mt7531-dsa-port" + properties: + gpio-controller: false + mediatek,mcm: false + + - if: + properties: + compatible: + const: mediatek,mt7621 + then: + $ref: "#/$defs/mt7530-dsa-port" + required: + - mediatek,mcm + + - if: + properties: + compatible: + const: mediatek,mt7988-switch + then: + $ref: "#/$defs/mt7530-dsa-port" + properties: + gpio-controller: false + mediatek,mcm: false + reset-names: false + unevaluatedProperties: false examples: + # Example 1: Standalone MT7530 - | #include <dt-bindings/gpio/gpio.h> + mdio { #address-cells = <1>; #size-cells = <0>; - switch@0 { + + switch@1f { compatible = "mediatek,mt7530"; - reg = <0>; + reg = <0x1f>; + + reset-gpios = <&pio 33 0>; core-supply = <&mt6323_vpa_reg>; io-supply = <&mt6323_vemc3v3_reg>; - reset-gpios = <&pio 33 GPIO_ACTIVE_HIGH>; ethernet-ports { #address-cells = <1>; #size-cells = <0>; + port@0 { reg = <0>; - label = "lan0"; + label = "lan1"; }; port@1 { reg = <1>; - label = "lan1"; + label = "lan2"; }; port@2 { reg = <2>; - label = "lan2"; + label = "lan3"; }; port@3 { reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 2: MT7530 in MT7623AI SoC + - | + #include <dt-bindings/reset/mt2701-resets.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7530"; + reg = <0x1f>; + + mediatek,mcm; + resets = <ðsys MT2701_ETHSYS_MCM_RST>; + reset-names = "mcm"; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; label = "lan3"; }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@4 { reg = <4>; label = "wan"; @@ -216,96 +406,226 @@ examples: port@6 { reg = <6>; - label = "cpu"; ethernet = <&gmac0>; phy-mode = "trgmii"; + fixed-link { speed = <1000>; full-duplex; + pause; }; }; }; }; }; + # Example 3: Standalone MT7531 - | - //Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4. + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> - ethernet { + mdio { #address-cells = <1>; #size-cells = <0>; - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; + + switch@0 { + compatible = "mediatek,mt7531"; reg = <0>; - phy-mode = "rgmii"; - fixed-link { - speed = <1000>; - full-duplex; - pause; + reset-gpios = <&pio 54 0>; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; + + # Example 4: MT7530 in MT7621AT, MT7621DAT and MT7621ST SoCs + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; }; }; + }; + + # Example 5: MT7621: mux MT7530's phy4 to SoC's gmac1 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> - gmac1: mac@1 { + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mac@1 { compatible = "mediatek,eth-mac"; reg = <1>; - phy-mode = "rgmii-txid"; - phy-handle = <&phy4>; + + phy-mode = "rgmii"; + phy-handle = <&example5_ethphy4>; }; - mdio: mdio-bus { + mdio { #address-cells = <1>; #size-cells = <0>; - /* Internal phy */ - phy4: ethernet-phy@4 { + /* MT7530's phy4 */ + example5_ethphy4: ethernet-phy@4 { reg = <4>; }; - mt7530: switch@1f { + switch@1f { compatible = "mediatek,mt7621"; reg = <0x1f>; - mediatek,mcm; - resets = <&rstctrl 2>; + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; reset-names = "mcm"; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + ethernet-ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; - label = "lan0"; + label = "lan1"; }; port@1 { reg = <1>; - label = "lan1"; + label = "lan2"; }; port@2 { reg = <2>; - label = "lan2"; + label = "lan3"; }; port@3 { reg = <3>; - label = "lan3"; + label = "lan4"; }; - /* Commented out. Port 4 is handled by 2nd GMAC. + /* Commented out, phy4 is connected to gmac1. port@4 { reg = <4>; - label = "lan4"; + label = "wan"; }; */ port@6 { reg = <6>; - label = "cpu"; ethernet = <&gmac0>; - phy-mode = "rgmii"; + phy-mode = "trgmii"; fixed-link { speed = <1000>; @@ -318,82 +638,169 @@ examples: }; }; + # Example 6: MT7621: mux external phy to SoC's gmac1 - | - //Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY. + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> ethernet { #address-cells = <1>; #size-cells = <0>; - gmac_0: mac@0 { + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mac@1 { compatible = "mediatek,eth-mac"; - reg = <0>; + reg = <1>; + phy-mode = "rgmii"; + phy-handle = <&example6_ethphy7>; + }; - fixed-link { - speed = <1000>; - full-duplex; - pause; + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* External PHY */ + example6_ethphy7: ethernet-phy@7 { + reg = <7>; + phy-mode = "rgmii"; + }; + + switch@1f { + compatible = "mediatek,mt7621"; + reg = <0x1f>; + + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; + reset-names = "mcm"; + + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; }; }; + }; - mdio0: mdio-bus { + # Example 7: MT7621: mux external phy to MT7530's port 5 + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + #include <dt-bindings/reset/mt7621-reset.h> + + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&rgmii2_pins>; + + mdio { #address-cells = <1>; #size-cells = <0>; - /* External phy */ - ephy5: ethernet-phy@7 { + /* External PHY */ + example7_ethphy7: ethernet-phy@7 { reg = <7>; + phy-mode = "rgmii"; }; switch@1f { compatible = "mediatek,mt7621"; reg = <0x1f>; - mediatek,mcm; - resets = <&rstctrl 2>; + mediatek,mcm; + resets = <&sysc MT7621_RST_MCM>; reset-names = "mcm"; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>; + ethernet-ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; - label = "lan0"; + label = "lan1"; }; port@1 { reg = <1>; - label = "lan1"; + label = "lan2"; }; port@2 { reg = <2>; - label = "lan2"; + label = "lan3"; }; port@3 { reg = <3>; - label = "lan3"; + label = "lan4"; }; port@4 { reg = <4>; - label = "lan4"; + label = "wan"; }; port@5 { reg = <5>; - label = "lan5"; - phy-mode = "rgmii"; - phy-handle = <&ephy5>; + label = "extphy"; + phy-mode = "rgmii-txid"; + phy-handle = <&example7_ethphy7>; }; - cpu_port0: port@6 { + port@6 { reg = <6>; - label = "cpu"; - ethernet = <&gmac_0>; - phy-mode = "rgmii"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; fixed-link { speed = <1000>; diff --git a/dts/Bindings/net/dsa/microchip,ksz.yaml b/dts/Bindings/net/dsa/microchip,ksz.yaml index 6bbd8145b6..52acc15ebc 100644 --- a/dts/Bindings/net/dsa/microchip,ksz.yaml +++ b/dts/Bindings/net/dsa/microchip,ksz.yaml @@ -11,7 +11,6 @@ maintainers: - Woojung Huh <Woojung.Huh@microchip.com> allOf: - - $ref: dsa.yaml# - $ref: /schemas/spi/spi-peripheral-props.yaml# properties: @@ -32,12 +31,15 @@ properties: - microchip,ksz9893 - microchip,ksz9563 - microchip,ksz8563 + - microchip,ksz8567 reset-gpios: description: Should be a gpio specifier for a reset line. maxItems: 1 + wakeup-source: true + microchip,synclko-125: $ref: /schemas/types.yaml#/definitions/flag description: @@ -49,10 +51,66 @@ properties: Set if the output SYNCLKO clock should be disabled. Do not mix with microchip,synclko-125. + microchip,io-drive-strength-microamp: + description: + IO Pad Drive Strength + enum: [8000, 16000] + default: 16000 + + microchip,hi-drive-strength-microamp: + description: + High Speed Drive Strength. Controls drive strength of GMII / RGMII / + MII / RMII (except TX_CLK/REFCLKI, COL and CRS) and CLKO_25_125 lines. + enum: [2000, 4000, 8000, 12000, 16000, 20000, 24000, 28000] + default: 24000 + + microchip,lo-drive-strength-microamp: + description: + Low Speed Drive Strength. Controls drive strength of TX_CLK / REFCLKI, + COL, CRS, LEDs, PME_N, NTRP_N, SDO and SDI/SDA/MDIO lines. + enum: [2000, 4000, 8000, 12000, 16000, 20000, 24000, 28000] + default: 8000 + + interrupts: + maxItems: 1 + required: - compatible - reg +if: + not: + properties: + compatible: + enum: + - microchip,ksz8863 + - microchip,ksz8873 +then: + $ref: dsa.yaml#/$defs/ethernet-ports +else: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-2]$": + $ref: dsa-port.yaml# + unevaluatedProperties: false + properties: + microchip,rmii-clk-internal: + $ref: /schemas/types.yaml#/definitions/flag + description: + When ksz88x3 is acting as clock provier (via REFCLKO) it + can select between internal and external RMII reference + clock. Internal reference clock means that the clock for + the RMII of ksz88x3 is provided by the ksz88x3 internally + and the REFCLKI pin is unconnected. For the external + reference clock, the clock needs to be fed back to ksz88x3 + via REFCLKI. + If microchip,rmii-clk-internal is set, ksz88x3 will provide + rmii reference clock internally, otherwise reference clock + should be provided externally. + dependencies: + microchip,rmii-clk-internal: [ethernet] + unevaluatedProperties: false examples: @@ -67,7 +125,7 @@ examples: }; }; - spi0 { + spi { #address-cells = <1>; #size-cells = <0>; @@ -107,8 +165,9 @@ examples: }; port@5 { reg = <5>; - label = "cpu"; ethernet = <ð0>; + phy-mode = "rgmii"; + fixed-link { speed = <1000>; full-duplex; @@ -144,8 +203,9 @@ examples: }; port@6 { reg = <6>; - label = "cpu"; ethernet = <ð0>; + phy-mode = "rgmii"; + fixed-link { speed = <1000>; full-duplex; diff --git a/dts/Bindings/net/dsa/microchip,lan937x.yaml b/dts/Bindings/net/dsa/microchip,lan937x.yaml index 630bf0f829..9973d64f15 100644 --- a/dts/Bindings/net/dsa/microchip,lan937x.yaml +++ b/dts/Bindings/net/dsa/microchip,lan937x.yaml @@ -4,13 +4,13 @@ $id: http://devicetree.org/schemas/net/dsa/microchip,lan937x.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: LAN937x Ethernet Switch Series Tree Bindings +title: LAN937x Ethernet Switch Series maintainers: - UNGLinuxDriver@microchip.com allOf: - - $ref: dsa.yaml# + - $ref: dsa.yaml#/$defs/ethernet-ports properties: compatible: @@ -37,8 +37,9 @@ properties: patternProperties: "^(ethernet-)?ports$": + additionalProperties: true patternProperties: - "^(ethernet-)?port@[0-9]+$": + "^(ethernet-)?port@[0-7]$": allOf: - if: properties: diff --git a/dts/Bindings/net/dsa/mscc,ocelot.yaml b/dts/Bindings/net/dsa/mscc,ocelot.yaml new file mode 100644 index 0000000000..fe02d05196 --- /dev/null +++ b/dts/Bindings/net/dsa/mscc,ocelot.yaml @@ -0,0 +1,260 @@ +# SPDX-License-Identifier: (GPL-2.0 OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/mscc,ocelot.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip Ocelot Switch Family + +maintainers: + - Vladimir Oltean <vladimir.oltean@nxp.com> + - Claudiu Manoil <claudiu.manoil@nxp.com> + - Alexandre Belloni <alexandre.belloni@bootlin.com> + - UNGLinuxDriver@microchip.com + +description: | + There are multiple switches which are either part of the Ocelot-1 family, or + derivatives of this architecture. These switches can be found embedded in + various SoCs and accessed using MMIO, or as discrete chips and accessed over + SPI or PCIe. The present DSA binding shall be used when the host controlling + them performs packet I/O primarily through an Ethernet port of the switch + (which is attached to an Ethernet port of the host), rather than through + Frame DMA or register-based I/O. + + VSC9953 (Seville): + + This is found in the NXP T1040, where it is a memory-mapped platform + device. + + The following PHY interface types are supported: + + - phy-mode = "internal": on ports 8 and 9 + - phy-mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 + - phy-mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 + - phy-mode = "1000base-x": on ports 0, 1, 2, 3, 4, 5, 6, 7 + + VSC9959 (Felix): + + This is found in the NXP LS1028A. It is a PCI device, part of the larger + enetc root complex. As a result, the ethernet-switch node is a sub-node of + the PCIe root complex node and its "reg" property conforms to the parent + node bindings, describing it as PF 5 of device 0, bus 0. + + If any external switch port is enabled, the enetc PF2 (enetc_port2) should + be enabled as well. This is because the internal MDIO bus (exposed through + EA BAR 0) used to access the MAC PCS registers truly belongs to the enetc + port 2 and not to Felix. + + The following PHY interface types are supported: + + - phy-mode = "internal": on ports 4 and 5 + - phy-mode = "sgmii": on ports 0, 1, 2, 3 + - phy-mode = "qsgmii": on ports 0, 1, 2, 3 + - phy-mode = "usxgmii": on ports 0, 1, 2, 3 + - phy-mode = "1000base-x": on ports 0, 1, 2, 3 + - phy-mode = "2500base-x": on ports 0, 1, 2, 3 + +properties: + compatible: + enum: + - mscc,vsc9953-switch + - pci1957,eef0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + description: + Used to signal availability of PTP TX timestamps, and state changes of + the MAC merge layer of ports that support Frame Preemption. + + little-endian: true + big-endian: true + +required: + - compatible + - reg + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + - if: + properties: + compatible: + const: pci1957,eef0 + then: + required: + - interrupts + +unevaluatedProperties: false + +examples: + # Felix VSC9959 (NXP LS1028A) + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + pcie { /* Integrated Endpoint Root Complex */ + #address-cells = <3>; + #size-cells = <2>; + + ethernet-switch@0,5 { + compatible = "pci1957,eef0"; + reg = <0x000500 0 0 0 0>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "qsgmii"; + phy-handle = <&phy0>; + managed = "in-band-status"; + }; + + port@1 { + reg = <1>; + phy-mode = "qsgmii"; + phy-handle = <&phy1>; + managed = "in-band-status"; + }; + + port@2 { + reg = <2>; + phy-mode = "qsgmii"; + phy-handle = <&phy2>; + managed = "in-band-status"; + }; + + port@3 { + reg = <3>; + phy-mode = "qsgmii"; + phy-handle = <&phy3>; + managed = "in-band-status"; + }; + + port@4 { + reg = <4>; + ethernet = <&enetc_port2>; + phy-mode = "internal"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + port@5 { + reg = <5>; + ethernet = <&enetc_port3>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + # Seville VSC9953 (NXP T1040) + - | + soc { + #address-cells = <1>; + #size-cells = <1>; + + ethernet-switch@800000 { + compatible = "mscc,vsc9953-switch"; + reg = <0x800000 0x290000>; + little-endian; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "qsgmii"; + phy-handle = <&phy0>; + managed = "in-band-status"; + }; + + port@1 { + reg = <1>; + phy-mode = "qsgmii"; + phy-handle = <&phy1>; + managed = "in-band-status"; + }; + + port@2 { + reg = <2>; + phy-mode = "qsgmii"; + phy-handle = <&phy2>; + managed = "in-band-status"; + }; + + port@3 { + reg = <3>; + phy-mode = "qsgmii"; + phy-handle = <&phy3>; + managed = "in-band-status"; + }; + + port@4 { + reg = <4>; + phy-mode = "qsgmii"; + phy-handle = <&phy4>; + managed = "in-band-status"; + }; + + port@5 { + reg = <5>; + phy-mode = "qsgmii"; + phy-handle = <&phy5>; + managed = "in-band-status"; + }; + + port@6 { + reg = <6>; + phy-mode = "qsgmii"; + phy-handle = <&phy6>; + managed = "in-band-status"; + }; + + port@7 { + reg = <7>; + phy-mode = "qsgmii"; + phy-handle = <&phy7>; + managed = "in-band-status"; + }; + + port@8 { + reg = <8>; + phy-mode = "internal"; + ethernet = <&enet0>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + port@9 { + reg = <9>; + phy-mode = "internal"; + ethernet = <&enet1>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; diff --git a/dts/Bindings/net/dsa/nxp,sja1105.yaml b/dts/Bindings/net/dsa/nxp,sja1105.yaml index 1e26d876d1..9432565f4f 100644 --- a/dts/Bindings/net/dsa/nxp,sja1105.yaml +++ b/dts/Bindings/net/dsa/nxp,sja1105.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/dsa/nxp,sja1105.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: NXP SJA1105 Automotive Ethernet Switch Family Device Tree Bindings +title: NXP SJA1105 Automotive Ethernet Switch Family description: The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944.pdf) of at @@ -12,10 +12,6 @@ description: cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed depends on the SPI bus master driver. -allOf: - - $ref: "dsa.yaml#" - - $ref: /schemas/spi/spi-peripheral-props.yaml# - maintainers: - Vladimir Oltean <vladimir.oltean@nxp.com> @@ -36,6 +32,9 @@ properties: reg: maxItems: 1 + spi-cpha: true + spi-cpol: true + # Optional container node for the 2 internal MDIO buses of the SJA1110 # (one for the internal 100base-T1 PHYs and the other for the single # 100base-TX PHY). The "reg" property does not have physical significance. @@ -44,6 +43,7 @@ properties: # PHY 1. mdios: type: object + additionalProperties: false properties: '#address-cells': @@ -75,8 +75,9 @@ properties: patternProperties: "^(ethernet-)?ports$": + additionalProperties: true patternProperties: - "^(ethernet-)?port@[0-9]+$": + "^(ethernet-)?port@[0-9]$": allOf: - if: properties: @@ -109,6 +110,30 @@ $defs: 1860, 1880, 1900, 1920, 1940, 1960, 1980, 2000, 2020, 2040, 2060, 2080, 2100, 2120, 2140, 2160, 2180, 2200, 2220, 2240, 2260] +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: + properties: + compatible: + enum: + - nxp,sja1105e + - nxp,sja1105p + - nxp,sja1105q + - nxp,sja1105r + - nxp,sja1105s + - nxp,sja1105t + then: + properties: + spi-cpol: false + required: + - spi-cpha + else: + properties: + spi-cpha: false + required: + - spi-cpol + unevaluatedProperties: false examples: @@ -120,6 +145,7 @@ examples: ethernet-switch@1 { reg = <0x1>; compatible = "nxp,sja1105t"; + spi-cpha; ethernet-ports { #address-cells = <1>; diff --git a/dts/Bindings/net/dsa/ocelot.txt b/dts/Bindings/net/dsa/ocelot.txt deleted file mode 100644 index 7a271d070b..0000000000 --- a/dts/Bindings/net/dsa/ocelot.txt +++ /dev/null @@ -1,213 +0,0 @@ -Microchip Ocelot switch driver family -===================================== - -Felix ------ - -Currently the switches supported by the felix driver are: - -- VSC9959 (Felix) -- VSC9953 (Seville) - -The VSC9959 switch is found in the NXP LS1028A. It is a PCI device, part of the -larger ENETC root complex. As a result, the ethernet-switch node is a sub-node -of the PCIe root complex node and its "reg" property conforms to the parent -node bindings: - -* reg: Specifies PCIe Device Number and Function Number of the endpoint device, - in this case for the Ethernet L2Switch it is PF5 (of device 0, bus 0). - -It does not require a "compatible" string. - -The interrupt line is used to signal availability of PTP TX timestamps and for -TSN frame preemption. - -For the external switch ports, depending on board configuration, "phy-mode" and -"phy-handle" are populated by board specific device tree instances. Ports 4 and -5 are fixed as internal ports in the NXP LS1028A instantiation. - -The CPU port property ("ethernet") configures the feature called "NPI port" in -the Ocelot hardware core. The CPU port in Ocelot is a set of queues, which are -connected, in the Node Processor Interface (NPI) mode, to an Ethernet port. -By default, in fsl-ls1028a.dtsi, the NPI port is assigned to the internal -2.5Gbps port@4, but can be moved to the 1Gbps port@5, depending on the specific -use case. Moving the NPI port to an external switch port is hardware possible, -but there is no platform support for the Linux system on the LS1028A chip to -operate as an entire slave DSA chip. NPI functionality (and therefore DSA -tagging) is supported on a single port at a time. - -Any port can be disabled (and in fsl-ls1028a.dtsi, they are indeed all disabled -by default, and should be enabled on a per-board basis). But if any external -switch port is enabled at all, the ENETC PF2 (enetc_port2) should be enabled as -well, regardless of whether it is configured as the DSA master or not. This is -because the Felix PHYLINK implementation accesses the MAC PCS registers, which -in hardware truly belong to the ENETC port #2 and not to Felix. - -Supported PHY interface types (appropriate SerDes protocol setting changes are -needed in the RCW binary): - -* phy_mode = "internal": on ports 4 and 5 -* phy_mode = "sgmii": on ports 0, 1, 2, 3 -* phy_mode = "qsgmii": on ports 0, 1, 2, 3 -* phy_mode = "usxgmii": on ports 0, 1, 2, 3 -* phy_mode = "2500base-x": on ports 0, 1, 2, 3 - -For the rest of the device tree binding definitions, which are standard DSA and -PCI, refer to the following documents: - -Documentation/devicetree/bindings/net/dsa/dsa.txt -Documentation/devicetree/bindings/pci/pci.txt - -Example: - -&soc { - pcie@1f0000000 { /* Integrated Endpoint Root Complex */ - ethernet-switch@0,5 { - reg = <0x000500 0 0 0 0>; - /* IEP INT_B */ - interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - /* External ports */ - port@0 { - reg = <0>; - label = "swp0"; - }; - - port@1 { - reg = <1>; - label = "swp1"; - }; - - port@2 { - reg = <2>; - label = "swp2"; - }; - - port@3 { - reg = <3>; - label = "swp3"; - }; - - /* Tagging CPU port */ - port@4 { - reg = <4>; - ethernet = <&enetc_port2>; - phy-mode = "internal"; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - - /* Non-tagging CPU port */ - port@5 { - reg = <5>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - }; -}; - -The VSC9953 switch is found inside NXP T1040. It is a platform device with the -following required properties: - -- compatible: - Must be "mscc,vsc9953-switch". - -Supported PHY interface types (appropriate SerDes protocol setting changes are -needed in the RCW binary): - -* phy_mode = "internal": on ports 8 and 9 -* phy_mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 -* phy_mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 - -Example: - -&soc { - ethernet-switch@800000 { - #address-cells = <0x1>; - #size-cells = <0x0>; - compatible = "mscc,vsc9953-switch"; - little-endian; - reg = <0x800000 0x290000>; - - ports { - #address-cells = <0x1>; - #size-cells = <0x0>; - - port@0 { - reg = <0x0>; - label = "swp0"; - }; - - port@1 { - reg = <0x1>; - label = "swp1"; - }; - - port@2 { - reg = <0x2>; - label = "swp2"; - }; - - port@3 { - reg = <0x3>; - label = "swp3"; - }; - - port@4 { - reg = <0x4>; - label = "swp4"; - }; - - port@5 { - reg = <0x5>; - label = "swp5"; - }; - - port@6 { - reg = <0x6>; - label = "swp6"; - }; - - port@7 { - reg = <0x7>; - label = "swp7"; - }; - - port@8 { - reg = <0x8>; - phy-mode = "internal"; - ethernet = <&enet0>; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - - port@9 { - reg = <0x9>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <2500>; - full-duplex; - }; - }; - }; - }; -}; diff --git a/dts/Bindings/net/dsa/qca,ar9331.yaml b/dts/Bindings/net/dsa/qca,ar9331.yaml new file mode 100644 index 0000000000..fd9ddc59d3 --- /dev/null +++ b/dts/Bindings/net/dsa/qca,ar9331.yaml @@ -0,0 +1,161 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/qca,ar9331.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Atheros AR9331 built-in switch + +maintainers: + - Oleksij Rempel <o.rempel@pengutronix.de> + +description: + Qualcomm Atheros AR9331 is a switch built-in to Atheros AR9331 WiSoC and + addressable over internal MDIO bus. All PHYs are built-in as well. + +properties: + compatible: + const: qca,ar9331-switch + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + const: 1 + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + properties: + interrupt-parent: true + + patternProperties: + '(ethernet-)?phy@[0-4]+$': + type: object + unevaluatedProperties: false + + properties: + reg: true + interrupts: + maxItems: 1 + + resets: + maxItems: 1 + + reset-names: + items: + - const: switch + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - mdio + - ports + - resets + - reset-names + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +unevaluatedProperties: false + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch10: switch@10 { + compatible = "qca,ar9331-switch"; + reg = <0x10>; + + interrupt-parent = <&miscintc>; + interrupts = <12>; + interrupt-controller; + #interrupt-cells = <1>; + + resets = <&rst 8>; + reset-names = "switch"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0x0>; + ethernet = <ð1>; + + phy-mode = "gmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <0x1>; + phy-handle = <&phy_port0>; + phy-mode = "internal"; + }; + + port@2 { + reg = <0x2>; + phy-handle = <&phy_port1>; + phy-mode = "internal"; + }; + + port@3 { + reg = <0x3>; + phy-handle = <&phy_port2>; + phy-mode = "internal"; + }; + + port@4 { + reg = <0x4>; + phy-handle = <&phy_port3>; + phy-mode = "internal"; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&switch10>; + + phy_port0: ethernet-phy@0 { + reg = <0x0>; + interrupts = <0>; + }; + + phy_port1: ethernet-phy@1 { + reg = <0x1>; + interrupts = <0>; + }; + + phy_port2: ethernet-phy@2 { + reg = <0x2>; + interrupts = <0>; + }; + + phy_port3: ethernet-phy@3 { + reg = <0x3>; + interrupts = <0>; + }; + + phy_port4: ethernet-phy@4 { + reg = <0x4>; + interrupts = <0>; + }; + }; + }; + }; diff --git a/dts/Bindings/net/dsa/qca8k.yaml b/dts/Bindings/net/dsa/qca8k.yaml index f3c88371d7..167398ab25 100644 --- a/dts/Bindings/net/dsa/qca8k.yaml +++ b/dts/Bindings/net/dsa/qca8k.yaml @@ -18,6 +18,8 @@ description: PHY it is connected to. In this config, an internal mdio-bus is registered and the MDIO master is used for communication. Mixed external and internal mdio-bus configurations are not supported by the hardware. + Each phy has at most 3 LEDs connected and can be declared + using the standard LEDs structure. properties: compatible: @@ -66,15 +68,12 @@ properties: With the legacy mapping the reg corresponding to the internal mdio is the switch reg with an offset of -1. +$ref: dsa.yaml# + patternProperties: "^(ethernet-)?ports$": type: object - properties: - '#address-cells': - const: 1 - '#size-cells': - const: 0 - + additionalProperties: true patternProperties: "^(ethernet-)?port@[0-6]$": type: object @@ -116,11 +115,12 @@ required: - compatible - reg -additionalProperties: true +unevaluatedProperties: false examples: - | #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/leds/common.h> mdio { #address-cells = <1>; @@ -148,8 +148,6 @@ examples: switch@10 { compatible = "qca,qca8337"; - #address-cells = <1>; - #size-cells = <0>; reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; reg = <0x10>; @@ -159,7 +157,6 @@ examples: port@0 { reg = <0>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; @@ -210,8 +207,6 @@ examples: switch@10 { compatible = "qca,qca8337"; - #address-cells = <1>; - #size-cells = <0>; reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; reg = <0x10>; @@ -221,7 +216,6 @@ examples: port@0 { reg = <0>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; @@ -236,6 +230,25 @@ examples: label = "lan1"; phy-mode = "internal"; phy-handle = <&internal_phy_port1>; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + color = <LED_COLOR_ID_WHITE>; + function = LED_FUNCTION_LAN; + default-state = "keep"; + }; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_AMBER>; + function = LED_FUNCTION_LAN; + default-state = "keep"; + }; + }; }; port@2 { @@ -268,7 +281,6 @@ examples: port@6 { reg = <0>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "sgmii"; diff --git a/dts/Bindings/net/dsa/realtek.yaml b/dts/Bindings/net/dsa/realtek.yaml index 4f99aff029..70b6bda3cf 100644 --- a/dts/Bindings/net/dsa/realtek.yaml +++ b/dts/Bindings/net/dsa/realtek.yaml @@ -7,7 +7,7 @@ $schema: http://devicetree.org/meta-schemas/core.yaml# title: Realtek switches for unmanaged switches allOf: - - $ref: dsa.yaml# + - $ref: dsa.yaml#/$defs/ethernet-ports maintainers: - Linus Walleij <linus.walleij@linaro.org> @@ -59,6 +59,9 @@ properties: description: GPIO to be used to reset the whole device maxItems: 1 + resets: + maxItems: 1 + realtek,disable-leds: type: boolean description: | @@ -68,6 +71,8 @@ properties: interrupt-controller: type: object + additionalProperties: false + description: | This defines an interrupt controller with an IRQ line (typically a GPIO) that will demultiplex and handle the interrupt from the single @@ -125,7 +130,6 @@ else: - mdc-gpios - mdio-gpios - mdio - - reset-gpios required: - compatible @@ -189,7 +193,6 @@ examples: }; port@5 { reg = <5>; - label = "cpu"; ethernet = <&gmac0>; phy-mode = "rgmii"; fixed-link { @@ -277,7 +280,6 @@ examples: }; port@6 { reg = <6>; - label = "cpu"; ethernet = <&fec1>; phy-mode = "rgmii"; tx-internal-delay-ps = <2000>; diff --git a/dts/Bindings/net/dsa/renesas,rzn1-a5psw.yaml b/dts/Bindings/net/dsa/renesas,rzn1-a5psw.yaml index 4d428f5ad0..ea285ef3e6 100644 --- a/dts/Bindings/net/dsa/renesas,rzn1-a5psw.yaml +++ b/dts/Bindings/net/dsa/renesas,rzn1-a5psw.yaml @@ -14,7 +14,7 @@ description: | handles 4 ports + 1 CPU management port. allOf: - - $ref: dsa.yaml# + - $ref: dsa.yaml#/$defs/ethernet-ports properties: compatible: @@ -61,23 +61,17 @@ properties: ethernet-ports: type: object - properties: - '#address-cells': - const: 1 - '#size-cells': - const: 0 - + additionalProperties: true patternProperties: "^(ethernet-)?port@[0-4]$": type: object - description: Ethernet switch ports - + additionalProperties: true properties: pcs-handle: + maxItems: 1 description: phandle pointing to a PCS sub-node compatible with renesas,rzn1-miic.yaml# - $ref: /schemas/types.yaml#/definitions/phandle unevaluatedProperties: false @@ -130,7 +124,8 @@ examples: port@4 { reg = <4>; ethernet = <&gmac2>; - label = "cpu"; + phy-mode = "internal"; + fixed-link { speed = <1000>; full-duplex; diff --git a/dts/Bindings/net/dsa/vitesse,vsc73xx.txt b/dts/Bindings/net/dsa/vitesse,vsc73xx.txt index bbf4a13f6d..258bef4836 100644 --- a/dts/Bindings/net/dsa/vitesse,vsc73xx.txt +++ b/dts/Bindings/net/dsa/vitesse,vsc73xx.txt @@ -75,7 +75,6 @@ switch@0 { }; vsc: port@6 { reg = <6>; - label = "cpu"; ethernet = <&gmac1>; phy-mode = "rgmii"; fixed-link { @@ -117,7 +116,6 @@ switch@2,0 { }; vsc: port@6 { reg = <6>; - label = "cpu"; ethernet = <&enet0>; phy-mode = "rgmii"; fixed-link { |