diff options
Diffstat (limited to 'dts/Bindings/net/hisilicon-hns-dsaf.txt')
| -rw-r--r-- | dts/Bindings/net/hisilicon-hns-dsaf.txt | 57 |
1 files changed, 47 insertions, 10 deletions
diff --git a/dts/Bindings/net/hisilicon-hns-dsaf.txt b/dts/Bindings/net/hisilicon-hns-dsaf.txt index ecacfa44b1..d4b7f2e499 100644 --- a/dts/Bindings/net/hisilicon-hns-dsaf.txt +++ b/dts/Bindings/net/hisilicon-hns-dsaf.txt @@ -7,19 +7,45 @@ Required properties: - mode: dsa fabric mode string. only support one of dsaf modes like these: "2port-64vf", "6port-16rss", - "6port-16vf". + "6port-16vf", + "single-port". - interrupt-parent: the interrupt parent of this device. - interrupts: should contain the DSA Fabric and rcb interrupt. - reg: specifies base physical address(es) and size of the device registers. - The first region is external interface control register base and size. - The second region is SerDes base register and size. + The first region is external interface control register base and size(optional, + only used when subctrl-syscon does not exist). It is recommended using + subctrl-syscon rather than this address. + The second region is SerDes base register and size(optional, only used when + serdes-syscon in port node does not exist). It is recommended using + serdes-syscon rather than this address. The third region is the PPE register base and size. - The fourth region is dsa fabric base register and size. - The fifth region is cpld base register and size, it is not required if do not use cpld. -- phy-handle: phy handle of physicl port, 0 if not any phy device. see ethernet.txt [1]. + The fourth region is dsa fabric base register and size. It is not required for + single-port mode. +- reg-names: may be ppe-base and(or) dsaf-base. It is used to find the + corresponding reg's index. + +- phy-handle: phy handle of physical port, 0 if not any phy device. It is optional + attribute. If port node exists, phy-handle in each port node will be used. + see ethernet.txt [1]. +- subctrl-syscon: is syscon handle for external interface control register. +- reset-field-offset: is offset of reset field. Its value depends on the hardware + user manual. - buf-size: rx buffer size, should be 16-1024. - desc-num: number of description in TX and RX queue, should be 512, 1024, 2048 or 4096. +- port: subnodes of dsaf. A dsaf node may contain several port nodes(Depending + on mode of dsaf). Port node contain some attributes listed below: +- reg: is physical port index in one dsaf. +- phy-handle: phy handle of physical port. It is not required if there isn't + phy device. see ethernet.txt [1]. +- serdes-syscon: is syscon handle for SerDes register. +- cpld-syscon: is syscon handle + register offset pair for cpld register. It is + not required if there isn't cpld device. +- port-rst-offset: is offset of reset field for each port in dsaf. Its value + depends on the hardware user manual. +- port-mode-offset: is offset of port mode field for each port in dsaf. Its + value depends on the hardware user manual. + [1] Documentation/devicetree/bindings/net/phy.txt Example: @@ -28,11 +54,11 @@ dsaf0: dsa@c7000000 { compatible = "hisilicon,hns-dsaf-v1"; mode = "6port-16rss"; interrupt-parent = <&mbigen_dsa>; - reg = <0x0 0xC0000000 0x0 0x420000 - 0x0 0xC2000000 0x0 0x300000 - 0x0 0xc5000000 0x0 0x890000 + reg = <0x0 0xc5000000 0x0 0x890000 0x0 0xc7000000 0x0 0x60000>; - phy-handle = <0 0 0 0 &soc0_phy4 &soc0_phy5 0 0>; + reg-names = "ppe-base", "dsaf-base"; + subctrl-syscon = <&subctrl>; + reset-field-offset = 0; interrupts = <131 4>,<132 4>, <133 4>,<134 4>, <135 4>,<136 4>, <137 4>,<138 4>, <139 4>,<140 4>, <141 4>,<142 4>, @@ -43,4 +69,15 @@ dsaf0: dsa@c7000000 { buf-size = <4096>; desc-num = <1024>; dma-coherent; + + port@0 { + reg = 0; + phy-handle = <&phy0>; + serdes-syscon = <&serdes>; + }; + + port@1 { + reg = 1; + serdes-syscon = <&serdes>; + }; }; |