1 files changed, 0 insertions, 60 deletions
diff --git a/dts/Bindings/net/macb.txt b/dts/Bindings/net/macb.txt
deleted file mode 100644
index a1b06fd196..0000000000
--- a/dts/Bindings/net/macb.txt
+++ /dev/null
@@ -1,60 +0,0 @@
-* Cadence MACB/GEM Ethernet controller
-
-Required properties:
-- compatible: Should be "cdns,[<chip>-]{macb|gem}"
-  Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC.
-  Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs.
-  Use "cdns,sam9x60-macb" for Microchip sam9x60 SoC.
-  Use "cdns,np4-macb" for NP4 SoC devices.
-  Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
-  Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs.
-  Use "atmel,sama5d29-gem" for GEM XL IP (10/100) available on Atmel sama5d29 SoCs.
-  Use "atmel,sama5d3-macb" for the 10/100Mbit IP available on Atmel sama5d3 SoCs.
-  Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs.
-  Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs.
-  Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC.
-  Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC.
-  Use "sifive,fu540-c000-gem" for SiFive FU540-C000 SoC.
-  Use "microchip,sama7g5-emac" for Microchip SAMA7G5 ethernet interface.
-  Use "microchip,sama7g5-gem" for Microchip SAMA7G5 gigabit ethernet interface.
-  Or the generic form: "cdns,emac".
-- reg: Address and length of the register set for the device
-	For "sifive,fu540-c000-gem", second range is required to specify the
-	address and length of the registers for GEMGXL Management block.
-- interrupts: Should contain macb interrupt
-- phy-mode: See ethernet.txt file in the same directory.
-- clock-names: Tuple listing input clock names.
-	Required elements: 'pclk', 'hclk'
-	Optional elements: 'tx_clk'
-	Optional elements: 'rx_clk' applies to cdns,zynqmp-gem
-	Optional elements: 'tsu_clk'
-- clocks: Phandles to input clocks.
-
-Optional properties:
-- mdio: node containing PHY children. If this node is not present, then PHYs
-        will be direct children.
-
-The MAC address will be determined using the optional properties
-defined in ethernet.txt.
-
-Optional properties for PHY child node:
-- reset-gpios : Should specify the gpio for phy reset
-- magic-packet : If present, indicates that the hardware supports waking
-  up via magic packet.
-- phy-handle : see ethernet.txt file in the same directory
-
-Examples:
-
-	macb0: ethernet@fffc4000 {
-		compatible = "cdns,at32ap7000-macb";
-		reg = <0xfffc4000 0x4000>;
-		interrupts = <21>;
-		phy-mode = "rmii";
-		local-mac-address = [3a 0e 03 04 05 06];
-		clock-names = "pclk", "hclk", "tx_clk";
-		clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>;
-		ethernet-phy@1 {
-			reg = <0x1>;
-			reset-gpios = <&pioE 6 1>;
-		};
-	};