1 files changed, 0 insertions, 85 deletions
diff --git a/dts/Bindings/net/sff,sfp.txt b/dts/Bindings/net/sff,sfp.txt
deleted file mode 100644
index 832139919f..0000000000
--- a/dts/Bindings/net/sff,sfp.txt
+++ /dev/null
@@ -1,85 +0,0 @@
-Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
-Transceiver
-
-Required properties:
-
-- compatible : must be one of
-  "sff,sfp" for SFP modules
-  "sff,sff" for soldered down SFF modules
-
-- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial
-  interface
-
-Optional Properties:
-
-- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS)
-  module presence input gpio signal, active (module absent) high. Must
-  not be present for SFF modules
-
-- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal
-  Indication input gpio signal, active (signal lost) high
-
-- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter
-  Fault input gpio signal, active (fault condition) high
-
-- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable
-  output gpio signal, active (Tx disable) high
-
-- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate
-  Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate
-  Must not be present for SFF modules
-
-- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate
-  Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
-  high Tx rate. Must not be present for SFF modules
-
-- maximum-power-milliwatt : Maximum module power consumption
-  Specifies the maximum power consumption allowable by a module in the
-  slot, in milli-Watts.  Presently, modules can be up to 1W, 1.5W or 2W.
-
-Example #1: Direct serdes to SFP connection
-
-sfp_eth3: sfp-eth3 {
-	compatible = "sff,sfp";
-	i2c-bus = <&sfp_1g_i2c>;
-	los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
-	mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
-	maximum-power-milliwatt = <1000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
-	tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
-	tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
-};
-
-&cps_emac3 {
-	phy-names = "comphy";
-	phys = <&cps_comphy5 0>;
-	sfp = <&sfp_eth3>;
-};
-
-Example #2: Serdes to PHY to SFP connection
-
-sfp_eth0: sfp-eth0 {
-	compatible = "sff,sfp";
-	i2c-bus = <&sfpp0_i2c>;
-	los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
-	mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&cps_sfpp0_pins>;
-	tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
-	tx-fault-gpios  = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
-};
-
-p0_phy: ethernet-phy@0 {
-	compatible = "ethernet-phy-ieee802.3-c45";
-	pinctrl-names = "default";
-	pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
-	reg = <0>;
-	interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
-	sfp = <&sfp_eth0>;
-};
-
-&cpm_eth0 {
-	phy = <&p0_phy>;
-	phy-mode = "10gbase-kr";
-};