1 files changed, 143 insertions, 0 deletions
diff --git a/dts/Bindings/net/sff,sfp.yaml b/dts/Bindings/net/sff,sfp.yaml
new file mode 100644
index 0000000000..bf6cbc7c2b
--- /dev/null
+++ b/dts/Bindings/net/sff,sfp.yaml
@@ -0,0 +1,143 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/sff,sfp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
+  Transceiver
+
+maintainers:
+  - Russell King <linux@armlinux.org.uk>
+
+properties:
+  compatible:
+    enum:
+      - sff,sfp  # for SFP modules
+      - sff,sff  # for soldered down SFF modules
+
+  i2c-bus:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      phandle of an I2C bus controller for the SFP two wire serial
+
+  maximum-power-milliwatt:
+    minimum: 1000
+    default: 1000
+    description:
+      Maximum module power consumption Specifies the maximum power consumption
+      allowable by a module in the slot, in milli-Watts. Presently, modules can
+      be up to 1W, 1.5W or 2W.
+
+  "mod-def0-gpios":
+    maxItems: 1
+    description:
+      GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module
+      presence input gpio signal, active (module absent) high. Must not be
+      present for SFF modules
+
+  "los-gpios":
+    maxItems: 1
+    description:
+      GPIO phandle and a specifier of the Receiver Loss of Signal Indication
+      input gpio signal, active (signal lost) high
+
+  "tx-fault-gpios":
+    maxItems: 1
+    description:
+      GPIO phandle and a specifier of the Module Transmitter Fault input gpio
+      signal, active (fault condition) high
+
+  "tx-disable-gpios":
+    maxItems: 1
+    description:
+      GPIO phandle and a specifier of the Transmitter Disable output gpio
+      signal, active (Tx disable) high
+
+  "rate-select0-gpios":
+    maxItems: 1
+    description:
+      GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0)
+      output gpio signal, low - low Rx rate, high - high Rx rate Must not be
+      present for SFF modules
+
+  "rate-select1-gpios":
+    maxItems: 1
+    description:
+      GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1)
+      output gpio signal (SFP+ only), low - low Tx rate, high - high Tx rate. Must
+      not be present for SFF modules
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: sff,sff
+    then:
+      properties:
+        mod-def0-gpios: false
+        rate-select0-gpios: false
+        rate-select1-gpios: false
+
+required:
+  - compatible
+  - i2c-bus
+
+additionalProperties: false
+
+examples:
+  - | # Direct serdes to SFP connection
+    #include <dt-bindings/gpio/gpio.h>
+
+    sfp1: sfp {
+      compatible = "sff,sfp";
+      i2c-bus = <&sfp_1g_i2c>;
+      los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
+      mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
+      maximum-power-milliwatt = <1000>;
+      pinctrl-names = "default";
+      pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
+      tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
+      tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
+    };
+
+    ethernet {
+      phy-names = "comphy";
+      phys = <&cps_comphy5 0>;
+      sfp = <&sfp1>;
+    };
+
+  - | # Serdes to PHY to SFP connection
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    sfp2: sfp {
+      compatible = "sff,sfp";
+      i2c-bus = <&sfp_i2c>;
+      los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
+      mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
+      pinctrl-names = "default";
+      pinctrl-0 = <&cps_sfpp0_pins>;
+      tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
+      tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
+    };
+
+    mdio {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      phy: ethernet-phy@0 {
+        compatible = "ethernet-phy-ieee802.3-c45";
+        pinctrl-names = "default";
+        pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
+        reg = <0>;
+        interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
+        sfp = <&sfp2>;
+      };
+    };
+
+    ethernet {
+      phy = <&phy>;
+      phy-mode = "10gbase-kr";
+    };