diff options
Diffstat (limited to 'dts/Bindings/pci/nvidia,tegra194-pcie.txt')
| -rw-r--r-- | dts/Bindings/pci/nvidia,tegra194-pcie.txt | 127 |
1 files changed, 100 insertions, 27 deletions
diff --git a/dts/Bindings/pci/nvidia,tegra194-pcie.txt b/dts/Bindings/pci/nvidia,tegra194-pcie.txt index b739f92da5..bd43f3c3ec 100644 --- a/dts/Bindings/pci/nvidia,tegra194-pcie.txt +++ b/dts/Bindings/pci/nvidia,tegra194-pcie.txt @@ -1,11 +1,11 @@ NVIDIA Tegra PCIe controller (Synopsys DesignWare Core based) -This PCIe host controller is based on the Synopsis Designware PCIe IP +This PCIe controller is based on the Synopsis Designware PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. +Some of the controller instances are dual mode where in they can work either +in root port mode or endpoint mode but one at a time. Required properties: -- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". -- device_type: Must be "pci" - power-domains: A phandle to the node that controls power to the respective PCIe controller and a specifier name for the PCIe controller. Following are the specifiers for the different PCIe controllers @@ -32,6 +32,32 @@ Required properties: entry for each entry in the interrupt-names property. - interrupt-names: Must include the following entries: "intr": The Tegra interrupt that is asserted for controller interrupts +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - core +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - apb + - core +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. +- phy-names: Must include an entry for each active lane. + "p2u-N": where N ranges from 0 to one less than the total number of lanes +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed + by controller-id. Following are the controller ids for each controller. + 0: C0 + 1: C1 + 2: C2 + 3: C3 + 4: C4 + 5: C5 +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals + +RC mode: +- compatible: Tegra19x must contain "nvidia,tegra194-pcie" +- device_type: Must be "pci" for RC mode +- interrupt-names: Must include the following entries: "msi": The Tegra interrupt that is asserted when an MSI is received - bus-range: Range of bus numbers associated with this controller - #address-cells: Address representation for root ports (must be 3) @@ -60,27 +86,15 @@ Required properties: - interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties Please refer to the standard PCI bus binding document for a more detailed explanation. -- clocks: Must contain an entry for each entry in clock-names. - See ../clocks/clock-bindings.txt for details. -- clock-names: Must include the following entries: - - core -- resets: Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names: Must include the following entries: - - apb - - core -- phys: Must contain a phandle to P2U PHY for each entry in phy-names. -- phy-names: Must include an entry for each active lane. - "p2u-N": where N ranges from 0 to one less than the total number of lanes -- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed - by controller-id. Following are the controller ids for each controller. - 0: C0 - 1: C1 - 2: C2 - 3: C3 - 4: C4 - 5: C5 -- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals + +EP mode: +In Tegra194, Only controllers C0, C4 & C5 support EP mode. +- compatible: Tegra19x must contain "nvidia,tegra194-pcie-ep" +- reg-names: Must include the following entries: + "addr_space": Used to map remote RC address space +- reset-gpios: Must contain a phandle to a GPIO controller followed by + GPIO that is being used as PERST input signal. Please refer to pci.txt + document. Optional properties: - pinctrl-names: A list of pinctrl state names. @@ -104,6 +118,8 @@ Optional properties: specified in microseconds - nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be specified in microseconds + +RC mode: - vpcie3v3-supply: A phandle to the regulator node that supplies 3.3V to the slot if the platform has one such slot. (Ex:- x16 slot owned by C5 controller in p2972-0000 platform). @@ -111,14 +127,21 @@ Optional properties: if the platform has one such slot. (Ex:- x16 slot owned by C5 controller in p2972-0000 platform). +EP mode: +- nvidia,refclk-select-gpios: Must contain a phandle to a GPIO controller + followed by GPIO that is being used to enable REFCLK to controller from host + +NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to +operate in the endpoint mode because of the way the platform is designed. + Examples: ========= -Tegra194: --------- +Tegra194 RC mode: +----------------- pcie@14180000 { - compatible = "nvidia,tegra194-pcie", "snps,dw-pcie"; + compatible = "nvidia,tegra194-pcie"; power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8B>; reg = <0x00 0x14180000 0x0 0x00020000 /* appl registers (128K) */ 0x00 0x38000000 0x0 0x00040000 /* configuration space (256K) */ @@ -169,3 +192,53 @@ Tegra194: <&p2u_hsio_5>; phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3"; }; + +Tegra194 EP mode: +----------------- + + pcie_ep@141a0000 { + compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep"; + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>; + reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ + 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ + 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ + 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ + reg-names = "appl", "atu_dma", "dbi", "addr_space"; + + num-lanes = <8>; + num-ib-windows = <2>; + num-ob-windows = <8>; + + pinctrl-names = "default"; + pinctrl-0 = <&clkreq_c5_bi_dir_state>; + + clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>; + clock-names = "core"; + + resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>, + <&bpmp TEGRA194_RESET_PEX1_CORE_5>; + reset-names = "apb", "core"; + + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ + interrupt-names = "intr"; + + nvidia,bpmp = <&bpmp 5>; + + nvidia,aspm-cmrt-us = <60>; + nvidia,aspm-pwr-on-t-us = <20>; + nvidia,aspm-l0s-entrance-latency-us = <3>; + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + + reset-gpios = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; + + nvidia,refclk-select-gpios = <&gpio_aon TEGRA194_AON_GPIO(AA, 5) + GPIO_ACTIVE_HIGH>; + + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, + <&p2u_nvhs_6>, <&p2u_nvhs_7>; + + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", + "p2u-5", "p2u-6", "p2u-7"; + }; |