1 files changed, 0 insertions, 84 deletions
diff --git a/dts/Bindings/pci/pci-rcar-gen2.txt b/dts/Bindings/pci/pci-rcar-gen2.txt
deleted file mode 100644
index aeba38f0a3..0000000000
--- a/dts/Bindings/pci/pci-rcar-gen2.txt
+++ /dev/null
@@ -1,84 +0,0 @@
-Renesas AHB to PCI bridge
--------------------------
-
-This is the bridge used internally to connect the USB controllers to the
-AHB. There is one bridge instance per USB port connected to the internal
-OHCI and EHCI controllers.
-
-Required properties:
-- compatible: "renesas,pci-r8a7742" for the R8A7742 SoC;
-	      "renesas,pci-r8a7743" for the R8A7743 SoC;
-	      "renesas,pci-r8a7744" for the R8A7744 SoC;
-	      "renesas,pci-r8a7745" for the R8A7745 SoC;
-	      "renesas,pci-r8a7790" for the R8A7790 SoC;
-	      "renesas,pci-r8a7791" for the R8A7791 SoC;
-	      "renesas,pci-r8a7793" for the R8A7793 SoC;
-	      "renesas,pci-r8a7794" for the R8A7794 SoC;
-	      "renesas,pci-rcar-gen2" for a generic R-Car Gen2 or
-				      RZ/G1 compatible device.
-
-
-	      When compatible with the generic version, nodes must list the
-	      SoC-specific version corresponding to the platform first
-	      followed by the generic version.
-
-- reg:	A list of physical regions to access the device: the first is
-	the operational registers for the OHCI/EHCI controllers and the
-	second is for the bridge configuration and control registers.
-- interrupts: interrupt for the device.
-- clocks: The reference to the device clock.
-- bus-range: The PCI bus number range; as this is a single bus, the range
-	     should be specified as the same value twice.
-- #address-cells: must be 3.
-- #size-cells: must be 2.
-- #interrupt-cells: must be 1.
-- interrupt-map: standard property used to define the mapping of the PCI
-  interrupts to the GIC interrupts.
-- interrupt-map-mask: standard property that helps to define the interrupt
-  mapping.
-
-Optional properties:
-- dma-ranges: a single range for the inbound memory region. If not supplied,
-  defaults to 1GiB at 0x40000000. Note there are hardware restrictions on the
-  allowed combinations of address and size.
-
-Example SoC configuration:
-
-	pci0: pci@ee090000  {
-		compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2";
-		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
-		reg = <0x0 0xee090000 0x0 0xc00>,
-		      <0x0 0xee080000 0x0 0x1100>;
-		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
-		status = "disabled";
-
-		bus-range = <0 0>;
-		#address-cells = <3>;
-		#size-cells = <2>;
-		#interrupt-cells = <1>;
-		dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>;
-		interrupt-map-mask = <0xff00 0 0 0x7>;
-		interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
-				 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
-				 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>;
-
-		usb@1,0 {
-			reg = <0x800 0 0 0 0>;
-			phys = <&usb0 0>;
-			phy-names = "usb";
-		};
-
-		usb@2,0 {
-			reg = <0x1000 0 0 0 0>;
-			phys = <&usb0 0>;
-			phy-names = "usb";
-		};
-	};
-
-Example board setup:
-
-&pci0 {
-	status = "okay";
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-};