summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/pci
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/pci')
-rw-r--r--dts/Bindings/pci/amlogic,meson-pcie.txt70
-rw-r--r--dts/Bindings/pci/fsl,imx6q-pcie.txt4
-rw-r--r--dts/Bindings/pci/host-generic-pci.txt2
-rw-r--r--dts/Bindings/pci/layerscape-pci.txt7
-rw-r--r--dts/Bindings/pci/mediatek-pcie.txt8
-rw-r--r--dts/Bindings/pci/uniphier-pcie.txt81
6 files changed, 159 insertions, 13 deletions
diff --git a/dts/Bindings/pci/amlogic,meson-pcie.txt b/dts/Bindings/pci/amlogic,meson-pcie.txt
new file mode 100644
index 0000000000..12b18f82d4
--- /dev/null
+++ b/dts/Bindings/pci/amlogic,meson-pcie.txt
@@ -0,0 +1,70 @@
+Amlogic Meson AXG DWC PCIE SoC controller
+
+Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
+It shares common functions with the PCIe DesignWare core driver and
+inherits common properties defined in
+Documentation/devicetree/bindings/pci/designware-pci.txt.
+
+Additional properties are described here:
+
+Required properties:
+- compatible:
+ should contain "amlogic,axg-pcie" to identify the core.
+- reg:
+ should contain the configuration address space.
+- reg-names: Must be
+ - "elbi" External local bus interface registers
+ - "cfg" Meson specific registers
+ - "phy" Meson PCIE PHY registers
+ - "config" PCIe configuration space
+- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Must include the following entries:
+ - "pclk" PCIe GEN 100M PLL clock
+ - "port" PCIe_x(A or B) RC clock gate
+ - "general" PCIe Phy clock
+ - "mipi" PCIe_x(A or B) 100M ref clock gate
+- resets: phandle to the reset lines.
+- reset-names: must contain "phy" "port" and "apb"
+ - "phy" Share PHY reset
+ - "port" Port A or B reset
+ - "apb" Share APB reset
+- device_type:
+ should be "pci". As specified in designware-pcie.txt
+
+
+Example configuration:
+
+ pcie: pcie@f9800000 {
+ compatible = "amlogic,axg-pcie", "snps,dw-pcie";
+ reg = <0x0 0xf9800000 0x0 0x400000
+ 0x0 0xff646000 0x0 0x2000
+ 0x0 0xff644000 0x0 0x2000
+ 0x0 0xf9f00000 0x0 0x100000>;
+ reg-names = "elbi", "cfg", "phy", "config";
+ reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
+ bus-range = <0x0 0xff>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
+
+ clocks = <&clkc CLKID_USB
+ &clkc CLKID_MIPI_ENABLE
+ &clkc CLKID_PCIE_A
+ &clkc CLKID_PCIE_CML_EN0>;
+ clock-names = "general",
+ "mipi",
+ "pclk",
+ "port";
+ resets = <&reset RESET_PCIE_PHY>,
+ <&reset RESET_PCIE_A>,
+ <&reset RESET_PCIE_APB>;
+ reset-names = "phy",
+ "port",
+ "apb";
+ };
diff --git a/dts/Bindings/pci/fsl,imx6q-pcie.txt b/dts/Bindings/pci/fsl,imx6q-pcie.txt
index f37494d5a7..d514c1f236 100644
--- a/dts/Bindings/pci/fsl,imx6q-pcie.txt
+++ b/dts/Bindings/pci/fsl,imx6q-pcie.txt
@@ -41,7 +41,9 @@ Optional properties:
Additional required properties for imx6sx-pcie:
- clock names: Must include the following additional entries:
- "pcie_inbound_axi"
-- power-domains: Must be set to a phandle pointing to the PCIE_PHY power domain
+- power-domains: Must be set to phandles pointing to the DISPLAY and
+ PCIE_PHY power domains
+- power-domain-names: Must be "pcie", "pcie_phy"
Additional required properties for imx7d-pcie:
- power-domains: Must be set to a phandle pointing to PCIE_PHY power domain
diff --git a/dts/Bindings/pci/host-generic-pci.txt b/dts/Bindings/pci/host-generic-pci.txt
index 3f1d3fca62..614b594f4e 100644
--- a/dts/Bindings/pci/host-generic-pci.txt
+++ b/dts/Bindings/pci/host-generic-pci.txt
@@ -56,7 +56,7 @@ For CAM, this 24-bit offset is:
cfg_offset(bus, device, function, register) =
bus << 16 | device << 11 | function << 8 | register
-Whilst ECAM extends this by 4 bits to accommodate 4k of function space:
+While ECAM extends this by 4 bits to accommodate 4k of function space:
cfg_offset(bus, device, function, register) =
bus << 20 | device << 15 | function << 12 | register
diff --git a/dts/Bindings/pci/layerscape-pci.txt b/dts/Bindings/pci/layerscape-pci.txt
index 66df1e81e0..9b2b8d66d1 100644
--- a/dts/Bindings/pci/layerscape-pci.txt
+++ b/dts/Bindings/pci/layerscape-pci.txt
@@ -13,11 +13,12 @@ information.
Required properties:
- compatible: should contain the platform identifier such as:
- "fsl,ls1021a-pcie", "snps,dw-pcie"
- "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", "snps,dw-pcie"
+ "fsl,ls1021a-pcie"
+ "fsl,ls2080a-pcie", "fsl,ls2085a-pcie"
"fsl,ls2088a-pcie"
"fsl,ls1088a-pcie"
"fsl,ls1046a-pcie"
+ "fsl,ls1043a-pcie"
"fsl,ls1012a-pcie"
- reg: base addresses and lengths of the PCIe controller register blocks.
- interrupts: A list of interrupt outputs of the controller. Must contain an
@@ -35,7 +36,7 @@ Required properties:
Example:
pcie@3400000 {
- compatible = "fsl,ls1021a-pcie", "snps,dw-pcie";
+ compatible = "fsl,ls1021a-pcie";
reg = <0x00 0x03400000 0x0 0x00010000 /* controller registers */
0x40 0x00000000 0x0 0x00002000>; /* configuration space */
reg-names = "regs", "config";
diff --git a/dts/Bindings/pci/mediatek-pcie.txt b/dts/Bindings/pci/mediatek-pcie.txt
index 20227a875a..92437a366e 100644
--- a/dts/Bindings/pci/mediatek-pcie.txt
+++ b/dts/Bindings/pci/mediatek-pcie.txt
@@ -65,7 +65,6 @@ Required properties:
explanation.
- ranges: Sub-ranges distributed from the PCIe controller node. An empty
property is sufficient.
-- num-lanes: Number of lanes to use for this port.
Examples for MT7623:
@@ -118,7 +117,6 @@ Examples for MT7623:
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>;
ranges;
- num-lanes = <1>;
};
pcie@1,0 {
@@ -129,7 +127,6 @@ Examples for MT7623:
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
ranges;
- num-lanes = <1>;
};
pcie@2,0 {
@@ -140,7 +137,6 @@ Examples for MT7623:
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
ranges;
- num-lanes = <1>;
};
};
@@ -172,7 +168,6 @@ Examples for MT2712:
#size-cells = <2>;
#interrupt-cells = <1>;
ranges;
- num-lanes = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie_intc0 0>,
<0 0 0 2 &pcie_intc0 1>,
@@ -191,7 +186,6 @@ Examples for MT2712:
#size-cells = <2>;
#interrupt-cells = <1>;
ranges;
- num-lanes = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie_intc1 0>,
<0 0 0 2 &pcie_intc1 1>,
@@ -245,7 +239,6 @@ Examples for MT7622:
#size-cells = <2>;
#interrupt-cells = <1>;
ranges;
- num-lanes = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie_intc0 0>,
<0 0 0 2 &pcie_intc0 1>,
@@ -264,7 +257,6 @@ Examples for MT7622:
#size-cells = <2>;
#interrupt-cells = <1>;
ranges;
- num-lanes = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &pcie_intc1 0>,
<0 0 0 2 &pcie_intc1 1>,
diff --git a/dts/Bindings/pci/uniphier-pcie.txt b/dts/Bindings/pci/uniphier-pcie.txt
new file mode 100644
index 0000000000..1fa2c5906d
--- /dev/null
+++ b/dts/Bindings/pci/uniphier-pcie.txt
@@ -0,0 +1,81 @@
+Socionext UniPhier PCIe host controller bindings
+
+This describes the devicetree bindings for PCIe host controller implemented
+on Socionext UniPhier SoCs.
+
+UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core.
+It shares common functions with the PCIe DesignWare core driver and inherits
+common properties defined in
+Documentation/devicetree/bindings/pci/designware-pcie.txt.
+
+Required properties:
+- compatible: Should be "socionext,uniphier-pcie".
+- reg: Specifies offset and length of the register set for the device.
+ According to the reg-names, appropriate register sets are required.
+- reg-names: Must include the following entries:
+ "dbi" - controller configuration registers
+ "link" - SoC-specific glue layer registers
+ "config" - PCIe configuration space
+- clocks: A phandle to the clock gate for PCIe glue layer including
+ the host controller.
+- resets: A phandle to the reset line for PCIe glue layer including
+ the host controller.
+- interrupts: A list of interrupt specifiers. According to the
+ interrupt-names, appropriate interrupts are required.
+- interrupt-names: Must include the following entries:
+ "dma" - DMA interrupt
+ "msi" - MSI interrupt
+
+Optional properties:
+- phys: A phandle to generic PCIe PHY. According to the phy-names, appropriate
+ phys are required.
+- phy-names: Must be "pcie-phy".
+
+Required sub-node:
+- legacy-interrupt-controller: Specifies interrupt controller for legacy PCI
+ interrupts.
+
+Required properties for legacy-interrupt-controller:
+- interrupt-controller: identifies the node as an interrupt controller.
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+- interrupt-parent: Phandle to the parent interrupt controller.
+- interrupts: An interrupt specifier for legacy interrupt.
+
+Example:
+
+ pcie: pcie@66000000 {
+ compatible = "socionext,uniphier-pcie", "snps,dw-pcie";
+ status = "disabled";
+ reg-names = "dbi", "link", "config";
+ reg = <0x66000000 0x1000>, <0x66010000 0x10000>,
+ <0x2fff0000 0x10000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ clocks = <&sys_clk 24>;
+ resets = <&sys_rst 24>;
+ num-lanes = <1>;
+ num-viewport = <1>;
+ bus-range = <0x0 0xff>;
+ device_type = "pci";
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 0x00000000 0x2ffe0000 0 0x00010000
+ /* non-prefetchable memory */
+ 0x82000000 0 0x00000000 0x20000000 0 0x0ffe0000>;
+ #interrupt-cells = <1>;
+ interrupt-names = "dma", "msi";
+ interrupts = <0 224 4>, <0 225 4>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie_intc 0>, /* INTA */
+ <0 0 0 2 &pcie_intc 1>, /* INTB */
+ <0 0 0 3 &pcie_intc 2>, /* INTC */
+ <0 0 0 4 &pcie_intc 3>; /* INTD */
+
+ pcie_intc: legacy-interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 226 4>;
+ };
+ };
generated by cgit v1.2.3 (git 2.39.1) at 2024-04-19 08:06:37 +0000