diff options
Diffstat (limited to 'dts/Bindings/pci')
| -rw-r--r-- | dts/Bindings/pci/aardvark-pci.txt | 56 | ||||
| -rw-r--r-- | dts/Bindings/pci/axis,artpec6-pcie.txt | 46 | ||||
| -rw-r--r-- | dts/Bindings/pci/layerscape-pci.txt | 4 |
3 files changed, 106 insertions, 0 deletions
diff --git a/dts/Bindings/pci/aardvark-pci.txt b/dts/Bindings/pci/aardvark-pci.txt new file mode 100644 index 0000000000..bbcd9f4c50 --- /dev/null +++ b/dts/Bindings/pci/aardvark-pci.txt @@ -0,0 +1,56 @@ +Aardvark PCIe controller + +This PCIe controller is used on the Marvell Armada 3700 ARM64 SoC. + +The Device Tree node describing an Aardvark PCIe controller must +contain the following properties: + + - compatible: Should be "marvell,armada-3700-pcie" + - reg: range of registers for the PCIe controller + - interrupts: the interrupt line of the PCIe controller + - #address-cells: set to <3> + - #size-cells: set to <2> + - device_type: set to "pci" + - ranges: ranges for the PCI memory and I/O regions + - #interrupt-cells: set to <1> + - msi-controller: indicates that the PCIe controller can itself + handle MSI interrupts + - msi-parent: pointer to the MSI controller to be used + - interrupt-map-mask and interrupt-map: standard PCI properties to + define the mapping of the PCIe interface to interrupt numbers. + - bus-range: PCI bus numbers covered + +In addition, the Device Tree describing an Aardvark PCIe controller +must include a sub-node that describes the legacy interrupt controller +built into the PCIe controller. This sub-node must have the following +properties: + + - interrupt-controller + - #interrupt-cells: set to <1> + +Example: + + pcie0: pcie@d0070000 { + compatible = "marvell,armada-3700-pcie"; + device_type = "pci"; + status = "disabled"; + reg = <0 0xd0070000 0 0x20000>; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x00 0xff>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <1>; + msi-controller; + msi-parent = <&pcie0>; + ranges = <0x82000000 0 0xe8000000 0 0xe8000000 0 0x1000000 /* Port 0 MEM */ + 0x81000000 0 0xe9000000 0 0xe9000000 0 0x10000>; /* Port 0 IO*/ + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 0>, + <0 0 0 2 &pcie_intc 1>, + <0 0 0 3 &pcie_intc 2>, + <0 0 0 4 &pcie_intc 3>; + pcie_intc: interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + }; + }; diff --git a/dts/Bindings/pci/axis,artpec6-pcie.txt b/dts/Bindings/pci/axis,artpec6-pcie.txt new file mode 100644 index 0000000000..330a45b5f0 --- /dev/null +++ b/dts/Bindings/pci/axis,artpec6-pcie.txt @@ -0,0 +1,46 @@ +* Axis ARTPEC-6 PCIe interface + +This PCIe host controller is based on the Synopsys DesignWare PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "axis,artpec6-pcie", "snps,dw-pcie" +- reg: base addresses and lengths of the PCIe controller (DBI), + the phy controller, and configuration address space. +- reg-names: Must include the following entries: + - "dbi" + - "phy" + - "config" +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + - "msi": The interrupt that is asserted when an MSI is received +- axis,syscon-pcie: A phandle pointing to the ARTPEC-6 system controller, + used to enable and control the Synopsys IP. + +Example: + + pcie@f8050000 { + compatible = "axis,artpec6-pcie", "snps,dw-pcie"; + reg = <0xf8050000 0x2000 + 0xf8040000 0x1000 + 0xc0000000 0x1000>; + reg-names = "dbi", "phy", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + /* downstream I/O */ + ranges = <0x81000000 0 0x00010000 0xc0010000 0 0x00010000 + /* non-prefetchable memory */ + 0x82000000 0 0xc0020000 0xc0020000 0 0x1ffe0000>; + num-lanes = <2>; + interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + axis,syscon-pcie = <&syscon>; + }; diff --git a/dts/Bindings/pci/layerscape-pci.txt b/dts/Bindings/pci/layerscape-pci.txt index ef683b2fd2..41e9f55a14 100644 --- a/dts/Bindings/pci/layerscape-pci.txt +++ b/dts/Bindings/pci/layerscape-pci.txt @@ -24,6 +24,9 @@ Required properties: The first entry must be a link to the SCFG device node The second entry must be '0' or '1' based on physical PCIe controller index. This is used to get SCFG PEXN registers +- dma-coherent: Indicates that the hardware IP block can ensure the coherency + of the data transferred from/to the IP block. This can avoid the software + cache flush/invalid actions, and improve the performance significantly. Example: @@ -38,6 +41,7 @@ Example: #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; num-lanes = <4>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */ |