diff options
Diffstat (limited to 'dts/Bindings/phy/phy-mtk-tphy.txt')
| -rw-r--r-- | dts/Bindings/phy/phy-mtk-tphy.txt | 162 |
1 files changed, 0 insertions, 162 deletions
diff --git a/dts/Bindings/phy/phy-mtk-tphy.txt b/dts/Bindings/phy/phy-mtk-tphy.txt deleted file mode 100644 index dd75b676b7..0000000000 --- a/dts/Bindings/phy/phy-mtk-tphy.txt +++ /dev/null @@ -1,162 +0,0 @@ -MediaTek T-PHY binding --------------------------- - -T-phy controller supports physical layer functionality for a number of -controllers on MediaTek SoCs, such as, USB2.0, USB3.0, PCIe, and SATA. - -Required properties (controller (parent) node): - - compatible : should be one of - "mediatek,generic-tphy-v1" - "mediatek,generic-tphy-v2" - "mediatek,mt2701-u3phy" (deprecated) - "mediatek,mt2712-u3phy" (deprecated) - "mediatek,mt8173-u3phy"; - make use of "mediatek,generic-tphy-v1" on mt2701 instead and - "mediatek,generic-tphy-v2" on mt2712 instead. - -- #address-cells: the number of cells used to represent physical - base addresses. -- #size-cells: the number of cells used to represent the size of an address. -- ranges: the address mapping relationship to the parent, defined with - - empty value: if optional 'reg' is used. - - non-empty value: if optional 'reg' is not used. should set - the child's base address to 0, the physical address - within parent's address space, and the length of - the address map. - -Required nodes : a sub-node is required for each port the controller - provides. Address range information including the usual - 'reg' property is used inside these nodes to describe - the controller's topology. - -Optional properties (controller (parent) node): - - reg : offset and length of register shared by multiple ports, - exclude port's private register. It is needed on mt2701 - and mt8173, but not on mt2712. - - mediatek,src-ref-clk-mhz : frequency of reference clock for slew rate - calibrate - - mediatek,src-coef : coefficient for slew rate calibrate, depends on - SoC process - -Required properties (port (child) node): -- reg : address and length of the register set for the port. -- #phy-cells : should be 1 (See second example) - cell after port phandle is phy type from: - - PHY_TYPE_USB2 - - PHY_TYPE_USB3 - - PHY_TYPE_PCIE - - PHY_TYPE_SATA - -Optional properties (PHY_TYPE_USB2 port (child) node): -- clocks : a list of phandle + clock-specifier pairs, one for each - entry in clock-names -- clock-names : may contain - "ref": 48M reference clock for HighSpeed (digital) phy; and 26M - reference clock for SuperSpeed (digital) phy, sometimes is - 24M, 25M or 27M, depended on platform. - "da_ref": the reference clock of analog phy, used if the clocks - of analog and digital phys are separated, otherwise uses - "ref" clock only if needed. - -- mediatek,eye-src : u32, the value of slew rate calibrate -- mediatek,eye-vrt : u32, the selection of VRT reference voltage -- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage -- mediatek,bc12 : bool, enable BC12 of u2phy if support it -- mediatek,discth : u32, the selection of disconnect threshold -- mediatek,intr : u32, the selection of internal R (resistance) - -Example: - -u3phy: usb-phy@11290000 { - compatible = "mediatek,mt8173-u3phy"; - reg = <0 0x11290000 0 0x800>; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - u2port0: usb-phy@11290800 { - reg = <0 0x11290800 0 0x100>; - clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; - clock-names = "ref"; - #phy-cells = <1>; - }; - - u3port0: usb-phy@11290900 { - reg = <0 0x11290800 0 0x700>; - clocks = <&clk26m>; - clock-names = "ref"; - #phy-cells = <1>; - }; - - u2port1: usb-phy@11291000 { - reg = <0 0x11291000 0 0x100>; - clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; - clock-names = "ref"; - #phy-cells = <1>; - }; -}; - -Specifying phy control of devices ---------------------------------- - -Device nodes should specify the configuration required in their "phys" -property, containing a phandle to the phy port node and a device type; -phy-names for each port are optional. - -Example: - -#include <dt-bindings/phy/phy.h> - -usb30: usb@11270000 { - ... - phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>; - phy-names = "usb2-0", "usb3-0"; - ... -}; - - -Layout differences of banks between mt8173/mt2701 and mt2712 -------------------------------------------------------------- -mt8173 and mt2701: -port offset bank -shared 0x0000 SPLLC - 0x0100 FMREG -u2 port0 0x0800 U2PHY_COM -u3 port0 0x0900 U3PHYD - 0x0a00 U3PHYD_BANK2 - 0x0b00 U3PHYA - 0x0c00 U3PHYA_DA -u2 port1 0x1000 U2PHY_COM -u3 port1 0x1100 U3PHYD - 0x1200 U3PHYD_BANK2 - 0x1300 U3PHYA - 0x1400 U3PHYA_DA -u2 port2 0x1800 U2PHY_COM - ... - -mt2712: -port offset bank -u2 port0 0x0000 MISC - 0x0100 FMREG - 0x0300 U2PHY_COM -u3 port0 0x0700 SPLLC - 0x0800 CHIP - 0x0900 U3PHYD - 0x0a00 U3PHYD_BANK2 - 0x0b00 U3PHYA - 0x0c00 U3PHYA_DA -u2 port1 0x1000 MISC - 0x1100 FMREG - 0x1300 U2PHY_COM -u3 port1 0x1700 SPLLC - 0x1800 CHIP - 0x1900 U3PHYD - 0x1a00 U3PHYD_BANK2 - 0x1b00 U3PHYA - 0x1c00 U3PHYA_DA -u2 port2 0x2000 MISC - ... - - SPLLC shared by u3 ports and FMREG shared by u2 ports on -mt8173/mt2701 are put back into each port; a new bank MISC for -u2 ports and CHIP for u3 ports are added on mt2712. |