summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/phy
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/phy')
-rw-r--r--dts/Bindings/phy/brcm,cygnus-pcie-phy.txt47
-rw-r--r--dts/Bindings/phy/calxeda-combophy.txt17
-rw-r--r--dts/Bindings/phy/keystone-usb-phy.txt20
-rw-r--r--dts/Bindings/phy/mxs-usb-phy.txt21
-rw-r--r--dts/Bindings/phy/nvidia,tegra20-usb-phy.txt72
-rw-r--r--dts/Bindings/phy/phy-mt65xx-usb.txt68
-rw-r--r--dts/Bindings/phy/qcom,usb-8x16-phy.txt76
-rw-r--r--dts/Bindings/phy/samsung-phy.txt3
8 files changed, 324 insertions, 0 deletions
diff --git a/dts/Bindings/phy/brcm,cygnus-pcie-phy.txt b/dts/Bindings/phy/brcm,cygnus-pcie-phy.txt
new file mode 100644
index 0000000000..761c4bc24a
--- /dev/null
+++ b/dts/Bindings/phy/brcm,cygnus-pcie-phy.txt
@@ -0,0 +1,47 @@
+Broadcom Cygnus PCIe PHY
+
+Required properties:
+- compatible: must be "brcm,cygnus-pcie-phy"
+- reg: base address and length of the PCIe PHY block
+- #address-cells: must be 1
+- #size-cells: must be 0
+
+Each PCIe PHY should be represented by a child node
+
+Required properties For the child node:
+- reg: the PHY ID
+0 - PCIe RC 0
+1 - PCIe RC 1
+- #phy-cells: must be 0
+
+Example:
+ pcie_phy: phy@0301d0a0 {
+ compatible = "brcm,cygnus-pcie-phy";
+ reg = <0x0301d0a0 0x14>;
+
+ pcie0_phy: phy@0 {
+ reg = <0>;
+ #phy-cells = <0>;
+ };
+
+ pcie1_phy: phy@1 {
+ reg = <1>;
+ #phy-cells = <0>;
+ };
+ };
+
+ /* users of the PCIe phy */
+
+ pcie0: pcie@18012000 {
+ ...
+ ...
+ phys = <&pcie0_phy>;
+ phy-names = "pcie-phy";
+ };
+
+ pcie1: pcie@18013000 {
+ ...
+ ...
+ phys = <pcie1_phy>;
+ phy-names = "pcie-phy";
+ };
diff --git a/dts/Bindings/phy/calxeda-combophy.txt b/dts/Bindings/phy/calxeda-combophy.txt
new file mode 100644
index 0000000000..6622bdb2e8
--- /dev/null
+++ b/dts/Bindings/phy/calxeda-combophy.txt
@@ -0,0 +1,17 @@
+Calxeda Highbank Combination Phys for SATA
+
+Properties:
+- compatible : Should be "calxeda,hb-combophy"
+- #phy-cells: Should be 1.
+- reg : Address and size for Combination Phy registers.
+- phydev: device ID for programming the combophy.
+
+Example:
+
+ combophy5: combo-phy@fff5d000 {
+ compatible = "calxeda,hb-combophy";
+ #phy-cells = <1>;
+ reg = <0xfff5d000 0x1000>;
+ phydev = <31>;
+ };
+
diff --git a/dts/Bindings/phy/keystone-usb-phy.txt b/dts/Bindings/phy/keystone-usb-phy.txt
new file mode 100644
index 0000000000..f37b3a8634
--- /dev/null
+++ b/dts/Bindings/phy/keystone-usb-phy.txt
@@ -0,0 +1,20 @@
+TI Keystone USB PHY
+
+Required properties:
+ - compatible: should be "ti,keystone-usbphy".
+ - #address-cells, #size-cells : should be '1' if the device has sub-nodes
+ with 'reg' property.
+ - reg : Address and length of the usb phy control register set.
+
+The main purpose of this PHY driver is to enable the USB PHY reference clock
+gate on the Keystone SOC for both the USB2 and USB3 PHY. Otherwise it is just
+an NOP PHY driver. Hence this node is referenced as both the usb2 and usb3
+phy node in the USB Glue layer driver node.
+
+usb_phy: usb_phy@2620738 {
+ compatible = "ti,keystone-usbphy";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x2620738 32>;
+ status = "disabled";
+};
diff --git a/dts/Bindings/phy/mxs-usb-phy.txt b/dts/Bindings/phy/mxs-usb-phy.txt
new file mode 100644
index 0000000000..379b84a567
--- /dev/null
+++ b/dts/Bindings/phy/mxs-usb-phy.txt
@@ -0,0 +1,21 @@
+* Freescale MXS USB Phy Device
+
+Required properties:
+- compatible: should contain:
+ * "fsl,imx23-usbphy" for imx23 and imx28
+ * "fsl,imx6q-usbphy" for imx6dq and imx6dl
+ * "fsl,imx6sl-usbphy" for imx6sl
+ * "fsl,vf610-usbphy" for Vybrid vf610
+ * "fsl,imx6sx-usbphy" for imx6sx
+ "fsl,imx23-usbphy" is still a fallback for other strings
+- reg: Should contain registers location and length
+- interrupts: Should contain phy interrupt
+- fsl,anatop: phandle for anatop register, it is only for imx6 SoC series
+
+Example:
+usbphy1: usbphy@020c9000 {
+ compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy";
+ reg = <0x020c9000 0x1000>;
+ interrupts = <0 44 0x04>;
+ fsl,anatop = <&anatop>;
+};
diff --git a/dts/Bindings/phy/nvidia,tegra20-usb-phy.txt b/dts/Bindings/phy/nvidia,tegra20-usb-phy.txt
new file mode 100644
index 0000000000..a9aa79fb90
--- /dev/null
+++ b/dts/Bindings/phy/nvidia,tegra20-usb-phy.txt
@@ -0,0 +1,72 @@
+Tegra SOC USB PHY
+
+The device node for Tegra SOC USB PHY:
+
+Required properties :
+ - compatible : For Tegra20, must contain "nvidia,tegra20-usb-phy".
+ For Tegra30, must contain "nvidia,tegra30-usb-phy". Otherwise, must contain
+ "nvidia,<chip>-usb-phy" plus at least one of the above, where <chip> is
+ tegra114, tegra124, tegra132, or tegra210.
+ - reg : Defines the following set of registers, in the order listed:
+ - The PHY's own register set.
+ Always present.
+ - The register set of the PHY containing the UTMI pad control registers.
+ Present if-and-only-if phy_type == utmi.
+ - phy_type : Should be one of "utmi", "ulpi" or "hsic".
+ - clocks : Defines the clocks listed in the clock-names property.
+ - clock-names : The following clock names must be present:
+ - reg: The clock needed to access the PHY's own registers. This is the
+ associated EHCI controller's clock. Always present.
+ - pll_u: PLL_U. Always present.
+ - timer: The timeout clock (clk_m). Present if phy_type == utmi.
+ - utmi-pads: The clock needed to access the UTMI pad control registers.
+ Present if phy_type == utmi.
+ - ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2).
+ Present if phy_type == ulpi, and ULPI link mode is in use.
+ - resets : Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+ - reset-names : Must include the following entries:
+ - usb: The PHY's own reset signal.
+ - utmi-pads: The reset of the PHY containing the chip-wide UTMI pad control
+ registers. Required even if phy_type == ulpi.
+
+Required properties for phy_type == ulpi:
+ - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
+
+Required PHY timing params for utmi phy, for all chips:
+ - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before
+ start of sync launches RxActive
+ - nvidia,elastic-limit : Variable FIFO Depth of elastic input store
+ - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait
+ before declare IDLE.
+ - nvidia,term-range-adj : Range adjusment on terminations
+ - Either one of the following for HS driver output control:
+ - nvidia,xcvr-setup : integer, uses the provided value.
+ - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read
+ from the on-chip fuses
+ If both are provided, nvidia,xcvr-setup-use-fuses takes precedence.
+ - nvidia,xcvr-lsfslew : LS falling slew rate control.
+ - nvidia,xcvr-lsrslew : LS rising slew rate control.
+
+Required PHY timing params for utmi phy, only on Tegra30 and above:
+ - nvidia,xcvr-hsslew : HS slew rate control.
+ - nvidia,hssquelch-level : HS squelch detector level.
+ - nvidia,hsdiscon-level : HS disconnect detector level.
+
+Optional properties:
+ - nvidia,has-legacy-mode : boolean indicates whether this controller can
+ operate in legacy mode (as APX 2500 / 2600). In legacy mode some
+ registers are accessed through the APB_MISC base address instead of
+ the USB controller.
+ - nvidia,is-wired : boolean. Indicates whether we can do certain kind of power
+ optimizations for the devices that are always connected. e.g. modem.
+ - dr_mode : dual role mode. Indicates the working mode for the PHY. Can be
+ "host", "peripheral", or "otg". Defaults to "host" if not defined.
+ host means this is a host controller
+ peripheral means it is device controller
+ otg means it can operate as either ("on the go")
+ - nvidia,has-utmi-pad-registers : boolean indicates whether this controller
+ contains the UTMI pad control registers common to all USB controllers.
+
+VBUS control (required for dr_mode == otg, optional for dr_mode == host):
+ - vbus-supply: regulator for VBUS
diff --git a/dts/Bindings/phy/phy-mt65xx-usb.txt b/dts/Bindings/phy/phy-mt65xx-usb.txt
new file mode 100644
index 0000000000..00100cf3e0
--- /dev/null
+++ b/dts/Bindings/phy/phy-mt65xx-usb.txt
@@ -0,0 +1,68 @@
+mt65xx USB3.0 PHY binding
+--------------------------
+
+This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+
+Required properties (controller (parent) node):
+ - compatible : should be "mediatek,mt8173-u3phy"
+ - reg : offset and length of register for phy, exclude port's
+ register.
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+ - clock-names : must contain
+ "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes : a sub-node is required for each port the controller
+ provides. Address range information including the usual
+ 'reg' property is used inside these nodes to describe
+ the controller's topology.
+
+Required properties (port (child) node):
+- reg : address and length of the register set for the port.
+- #phy-cells : should be 1 (See second example)
+ cell after port phandle is phy type from:
+ - PHY_TYPE_USB2
+ - PHY_TYPE_USB3
+
+Example:
+
+u3phy: usb-phy@11290000 {
+ compatible = "mediatek,mt8173-u3phy";
+ reg = <0 0x11290000 0 0x800>;
+ clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+ clock-names = "u3phya_ref";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "okay";
+
+ phy_port0: port@11290800 {
+ reg = <0 0x11290800 0 0x800>;
+ #phy-cells = <1>;
+ status = "okay";
+ };
+
+ phy_port1: port@11291000 {
+ reg = <0 0x11291000 0 0x800>;
+ #phy-cells = <1>;
+ status = "okay";
+ };
+};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb@11270000 {
+ ...
+ phys = <&phy_port0 PHY_TYPE_USB3>;
+ phy-names = "usb3-0";
+ ...
+};
diff --git a/dts/Bindings/phy/qcom,usb-8x16-phy.txt b/dts/Bindings/phy/qcom,usb-8x16-phy.txt
new file mode 100644
index 0000000000..2cb2168cef
--- /dev/null
+++ b/dts/Bindings/phy/qcom,usb-8x16-phy.txt
@@ -0,0 +1,76 @@
+Qualcomm's APQ8016/MSM8916 USB transceiver controller
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,usb-8x16-phy".
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: USB PHY base address and length of the register map
+
+- clocks:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: See clock-bindings.txt section "consumers". List of
+ two clock specifiers for interface and core controller
+ clocks.
+
+- clock-names:
+ Usage: required
+ Value type: <string>
+ Definition: Must contain "iface" and "core" strings.
+
+- vddcx-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: phandle to the regulator VDCCX supply node.
+
+- v1p8-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: phandle to the regulator 1.8V supply node.
+
+- v3p3-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: phandle to the regulator 3.3V supply node.
+
+- resets:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: See reset.txt section "consumers". PHY reset specifier.
+
+- reset-names:
+ Usage: required
+ Value type: <string>
+ Definition: Must contain "phy" string.
+
+- switch-gpio:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: Some boards are using Dual SPDT USB Switch, witch is
+ controlled by GPIO to de/multiplex D+/D- USB lines
+ between connectors.
+
+Example:
+ usb_phy: phy@78d9000 {
+ compatible = "qcom,usb-8x16-phy";
+ reg = <0x78d9000 0x400>;
+
+ vddcx-supply = <&pm8916_s1_corner>;
+ v1p8-supply = <&pm8916_l7>;
+ v3p3-supply = <&pm8916_l13>;
+
+ clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+ <&gcc GCC_USB_HS_SYSTEM_CLK>;
+ clock-names = "iface", "core";
+
+ resets = <&gcc GCC_USB2A_PHY_BCR>;
+ reset-names = "phy";
+
+ // D+/D- lines: 1 - Routed to HUB, 0 - Device connector
+ switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>;
+ };
+
diff --git a/dts/Bindings/phy/samsung-phy.txt b/dts/Bindings/phy/samsung-phy.txt
index 60c6f2a633..0289d3b078 100644
--- a/dts/Bindings/phy/samsung-phy.txt
+++ b/dts/Bindings/phy/samsung-phy.txt
@@ -44,6 +44,9 @@ Required properties:
- the "ref" clock is used to get the rate of the clock provided to the
PHY module
+Optional properties:
+- vbus-supply: power-supply phandle for vbus power source
+
The first phandle argument in the PHY specifier identifies the PHY, its
meaning is compatible dependent. For the currently supported SoCs (Exynos 4210
and Exynos 4212) it is as follows: