summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/phy
diff options
context:
space:
mode:
Diffstat (limited to 'dts/Bindings/phy')
-rw-r--r--dts/Bindings/phy/phy-mt65xx-usb.txt93
-rw-r--r--dts/Bindings/phy/phy-rockchip-inno-usb2.txt6
-rw-r--r--dts/Bindings/phy/qcom-qmp-phy.txt106
-rw-r--r--dts/Bindings/phy/qcom-qusb2-phy.txt43
-rw-r--r--dts/Bindings/phy/rockchip-usb-phy.txt1
-rw-r--r--dts/Bindings/phy/sun4i-usb-phy.txt1
6 files changed, 237 insertions, 13 deletions
diff --git a/dts/Bindings/phy/phy-mt65xx-usb.txt b/dts/Bindings/phy/phy-mt65xx-usb.txt
index 33a2b1ee3f..0acc5a99fb 100644
--- a/dts/Bindings/phy/phy-mt65xx-usb.txt
+++ b/dts/Bindings/phy/phy-mt65xx-usb.txt
@@ -6,12 +6,11 @@ This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
Required properties (controller (parent) node):
- compatible : should be one of
"mediatek,mt2701-u3phy"
+ "mediatek,mt2712-u3phy"
"mediatek,mt8173-u3phy"
- - reg : offset and length of register for phy, exclude port's
- register.
- - clocks : a list of phandle + clock-specifier pairs, one for each
- entry in clock-names
- - clock-names : must contain
+ - clocks : (deprecated, use port's clocks instead) a list of phandle +
+ clock-specifier pairs, one for each entry in clock-names
+ - clock-names : (deprecated, use port's one instead) must contain
"u3phya_ref": for reference clock of usb3.0 analog phy.
Required nodes : a sub-node is required for each port the controller
@@ -19,8 +18,19 @@ Required nodes : a sub-node is required for each port the controller
'reg' property is used inside these nodes to describe
the controller's topology.
+Optional properties (controller (parent) node):
+ - reg : offset and length of register shared by multiple ports,
+ exclude port's private register. It is needed on mt2701
+ and mt8173, but not on mt2712.
+
Required properties (port (child) node):
- reg : address and length of the register set for the port.
+- clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+- clock-names : must contain
+ "ref": 48M reference clock for HighSpeed analog phy; and 26M
+ reference clock for SuperSpeed analog phy, sometimes is
+ 24M, 25M or 27M, depended on platform.
- #phy-cells : should be 1 (See second example)
cell after port phandle is phy type from:
- PHY_TYPE_USB2
@@ -31,21 +41,31 @@ Example:
u3phy: usb-phy@11290000 {
compatible = "mediatek,mt8173-u3phy";
reg = <0 0x11290000 0 0x800>;
- clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
- clock-names = "u3phya_ref";
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "okay";
- phy_port0: port@11290800 {
- reg = <0 0x11290800 0 0x800>;
+ u2port0: usb-phy@11290800 {
+ reg = <0 0x11290800 0 0x100>;
+ clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+ clock-names = "ref";
#phy-cells = <1>;
status = "okay";
};
- phy_port1: port@11291000 {
- reg = <0 0x11291000 0 0x800>;
+ u3port0: usb-phy@11290900 {
+ reg = <0 0x11290800 0 0x700>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+
+ u2port1: usb-phy@11291000 {
+ reg = <0 0x11291000 0 0x100>;
+ clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+ clock-names = "ref";
#phy-cells = <1>;
status = "okay";
};
@@ -64,7 +84,54 @@ Example:
usb30: usb@11270000 {
...
- phys = <&phy_port0 PHY_TYPE_USB3>;
- phy-names = "usb3-0";
+ phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
+ phy-names = "usb2-0", "usb3-0";
...
};
+
+
+Layout differences of banks between mt8173/mt2701 and mt2712
+-------------------------------------------------------------
+mt8173 and mt2701:
+port offset bank
+shared 0x0000 SPLLC
+ 0x0100 FMREG
+u2 port0 0x0800 U2PHY_COM
+u3 port0 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+u2 port1 0x1000 U2PHY_COM
+u3 port1 0x1100 U3PHYD
+ 0x1200 U3PHYD_BANK2
+ 0x1300 U3PHYA
+ 0x1400 U3PHYA_DA
+u2 port2 0x1800 U2PHY_COM
+ ...
+
+mt2712:
+port offset bank
+u2 port0 0x0000 MISC
+ 0x0100 FMREG
+ 0x0300 U2PHY_COM
+u3 port0 0x0700 SPLLC
+ 0x0800 CHIP
+ 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+u2 port1 0x1000 MISC
+ 0x1100 FMREG
+ 0x1300 U2PHY_COM
+u3 port1 0x1700 SPLLC
+ 0x1800 CHIP
+ 0x1900 U3PHYD
+ 0x1a00 U3PHYD_BANK2
+ 0x1b00 U3PHYA
+ 0x1c00 U3PHYA_DA
+u2 port2 0x2000 MISC
+ ...
+
+ SPLLC shared by u3 ports and FMREG shared by u2 ports on
+mt8173/mt2701 are put back into each port; a new bank MISC for
+u2 ports and CHIP for u3 ports are added on mt2712.
diff --git a/dts/Bindings/phy/phy-rockchip-inno-usb2.txt b/dts/Bindings/phy/phy-rockchip-inno-usb2.txt
index 3c29c77a70..e71a8d23f4 100644
--- a/dts/Bindings/phy/phy-rockchip-inno-usb2.txt
+++ b/dts/Bindings/phy/phy-rockchip-inno-usb2.txt
@@ -2,6 +2,7 @@ ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
Required properties (phy (parent) node):
- compatible : should be one of the listed compatibles:
+ * "rockchip,rk3328-usb2phy"
* "rockchip,rk3366-usb2phy"
* "rockchip,rk3399-usb2phy"
- reg : the address offset of grf for usb-phy configuration.
@@ -11,6 +12,11 @@ Required properties (phy (parent) node):
Optional properties:
- clocks : phandle + phy specifier pair, for the input clock of phy.
- clock-names : input clock name of phy, must be "phyclk".
+ - assigned-clocks : phandle of usb 480m clock.
+ - assigned-clock-parents : parent of usb 480m clock, select between
+ usb-phy output 480m and xin24m.
+ Refer to clk/clock-bindings.txt for generic clock
+ consumer properties.
Required nodes : a sub-node is required for each port the phy provides.
The sub-node name is used to identify host or otg port,
diff --git a/dts/Bindings/phy/qcom-qmp-phy.txt b/dts/Bindings/phy/qcom-qmp-phy.txt
new file mode 100644
index 0000000000..e11c563a65
--- /dev/null
+++ b/dts/Bindings/phy/qcom-qmp-phy.txt
@@ -0,0 +1,106 @@
+Qualcomm QMP PHY controller
+===========================
+
+QMP phy controller supports physical layer functionality for a number of
+controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
+
+Required properties:
+ - compatible: compatible list, contains:
+ "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
+ "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996.
+
+ - reg: offset and length of register set for PHY's common serdes block.
+
+ - #clock-cells: must be 1
+ - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe
+ interface (for pipe based PHYs). These clock are then gate-controlled
+ by gcc.
+ - #address-cells: must be 1
+ - #size-cells: must be 1
+ - ranges: must be present
+
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: "cfg_ahb" for phy config clock,
+ "aux" for phy aux clock,
+ "ref" for 19.2 MHz ref clk,
+ For "qcom,msm8996-qmp-pcie-phy" must contain:
+ "aux", "cfg_ahb", "ref".
+ For "qcom,msm8996-qmp-usb3-phy" must contain:
+ "aux", "cfg_ahb", "ref".
+
+ - resets: a list of phandles and reset controller specifier pairs,
+ one for each entry in reset-names.
+ - reset-names: "phy" for reset of phy block,
+ "common" for phy common block reset,
+ "cfg" for phy's ahb cfg block reset (Optional).
+ For "qcom,msm8996-qmp-pcie-phy" must contain:
+ "phy", "common", "cfg".
+ For "qcom,msm8996-qmp-usb3-phy" must contain
+ "phy", "common".
+
+ - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
+ - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
+
+Optional properties:
+ - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
+ pll block.
+
+Required nodes:
+ - Each device node of QMP phy is required to have as many child nodes as
+ the number of lanes the PHY has.
+
+Required properties for child node:
+ - reg: list of offset and length pairs of register sets for PHY blocks -
+ tx, rx and pcs.
+
+ - #phy-cells: must be 0
+
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: Must contain following for pcie and usb qmp phys:
+ "pipe<lane-number>" for pipe clock specific to each lane.
+
+ - resets: a list of phandles and reset controller specifier pairs,
+ one for each entry in reset-names.
+ - reset-names: Must contain following for pcie qmp phys:
+ "lane<lane-number>" for reset specific to each lane.
+
+Example:
+ phy@34000 {
+ compatible = "qcom,msm8996-qmp-pcie-phy";
+ reg = <0x34000 0x488>;
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_CLKREF_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+
+ resets = <&gcc GCC_PCIE_PHY_BCR>,
+ <&gcc GCC_PCIE_PHY_COM_BCR>,
+ <&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
+ reset-names = "phy", "common", "cfg";
+
+ pciephy_0: lane@35000 {
+ reg = <0x35000 0x130>,
+ <0x35200 0x200>,
+ <0x35400 0x1dc>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ clock-names = "pipe0";
+ resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+ reset-names = "lane0";
+ };
+
+ pciephy_1: lane@36000 {
+ ...
+ ...
+ };
diff --git a/dts/Bindings/phy/qcom-qusb2-phy.txt b/dts/Bindings/phy/qcom-qusb2-phy.txt
new file mode 100644
index 0000000000..aa0fcb05ac
--- /dev/null
+++ b/dts/Bindings/phy/qcom-qusb2-phy.txt
@@ -0,0 +1,43 @@
+Qualcomm QUSB2 phy controller
+=============================
+
+QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
+
+Required properties:
+ - compatible: compatible list, contains "qcom,msm8996-qusb2-phy".
+ - reg: offset and length of the PHY register set.
+ - #phy-cells: must be 0.
+
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: must be "cfg_ahb" for phy config clock,
+ "ref" for 19.2 MHz ref clk,
+ "iface" for phy interface clock (Optional).
+
+ - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
+ - vdda-phy-dpdm-supply: Phandle to 3.1V regulator supply to Dp/Dm port signals.
+
+ - resets: Phandle to reset to phy block.
+
+Optional properties:
+ - nvmem-cells: Phandle to nvmem cell that contains 'HS Tx trim'
+ tuning parameter value for qusb2 phy.
+
+ - qcom,tcsr-syscon: Phandle to TCSR syscon register region.
+
+Example:
+ hsusb_phy: phy@7411000 {
+ compatible = "qcom,msm8996-qusb2-phy";
+ reg = <0x7411000 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_RX1_USB2_CLKREF_CLK>,
+ clock-names = "cfg_ahb", "ref";
+
+ vdda-pll-supply = <&pm8994_l12>;
+ vdda-phy-dpdm-supply = <&pm8994_l24>;
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+ nvmem-cells = <&qusb2p_hstx_trim>;
+ };
diff --git a/dts/Bindings/phy/rockchip-usb-phy.txt b/dts/Bindings/phy/rockchip-usb-phy.txt
index 57dc388e2f..4ed569046d 100644
--- a/dts/Bindings/phy/rockchip-usb-phy.txt
+++ b/dts/Bindings/phy/rockchip-usb-phy.txt
@@ -30,6 +30,7 @@ Optional Properties:
- reset-names: Only allow the following entries:
- phy-reset
- resets: Must contain an entry for each entry in reset-names.
+- vbus-supply: power-supply phandle for vbus power source
Example:
diff --git a/dts/Bindings/phy/sun4i-usb-phy.txt b/dts/Bindings/phy/sun4i-usb-phy.txt
index e423342581..005bc22938 100644
--- a/dts/Bindings/phy/sun4i-usb-phy.txt
+++ b/dts/Bindings/phy/sun4i-usb-phy.txt
@@ -15,6 +15,7 @@ Required properties:
- reg : a list of offset + length pairs
- reg-names :
* "phy_ctrl"
+ * "pmu0" for H3, V3s and A64
* "pmu1"
* "pmu2" for sun4i, sun6i or sun7i
- #phy-cells : from the generic phy bindings, must be 1
generated by cgit v1.2.3 (git 2.39.1) at 2024-04-27 21:32:10 +0000