diff options
Diffstat (limited to 'dts/Bindings/pinctrl/brcm,bcm11351-pinctrl.txt')
| -rw-r--r-- | dts/Bindings/pinctrl/brcm,bcm11351-pinctrl.txt | 461 |
1 files changed, 0 insertions, 461 deletions
diff --git a/dts/Bindings/pinctrl/brcm,bcm11351-pinctrl.txt b/dts/Bindings/pinctrl/brcm,bcm11351-pinctrl.txt deleted file mode 100644 index 4eaae32821..0000000000 --- a/dts/Bindings/pinctrl/brcm,bcm11351-pinctrl.txt +++ /dev/null @@ -1,461 +0,0 @@ -Broadcom BCM281xx Pin Controller - -This is a pin controller for the Broadcom BCM281xx SoC family, which includes -BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs. - -=== Pin Controller Node === - -Required Properties: - -- compatible: Must be "brcm,bcm11351-pinctrl" -- reg: Base address of the PAD Controller register block and the size - of the block. - -For example, the following is the bare minimum node: - - pinctrl@35004800 { - compatible = "brcm,bcm11351-pinctrl"; - reg = <0x35004800 0x430>; - }; - -As a pin controller device, in addition to the required properties, this node -should also contain the pin configuration nodes that client devices reference, -if any. - -=== Pin Configuration Node === - -Each pin configuration node is a sub-node of the pin controller node and is a -container of an arbitrary number of subnodes, called pin group nodes in this -document. - -Please refer to the pinctrl-bindings.txt in this directory for details of the -common pinctrl bindings used by client devices, including the definition of a -"pin configuration node". - -=== Pin Group Node === - -A pin group node specifies the desired pin mux and/or pin configuration for an -arbitrary number of pins. The name of the pin group node is optional and not -used. - -A pin group node only affects the properties specified in the node, and has no -effect on any properties that are omitted. - -The pin group node accepts a subset of the generic pin config properties. For -details generic pin config properties, please refer to pinctrl-bindings.txt -and <include/linux/pinctrl/pinconfig-generic.h>. - -Each pin controlled by this pin controller belong to one of three types: -Standard, I2C, and HDMI. Each type accepts a different set of pin config -properties. A list of pins and their types is provided below. - -Required Properties (applicable to all pins): - -- pins: Multiple strings. Specifies the name(s) of one or more pins to - be configured by this node. - -Optional Properties (for standard pins): - -- function: String. Specifies the pin mux selection. Values - must be one of: "alt1", "alt2", "alt3", "alt4" -- input-schmitt-enable: No arguments. Enable schmitt-trigger mode. -- input-schmitt-disable: No arguments. Disable schmitt-trigger mode. -- bias-pull-up: No arguments. Pull up on pin. -- bias-pull-down: No arguments. Pull down on pin. -- bias-disable: No arguments. Disable pin bias. -- slew-rate: Integer. Meaning depends on configured pin mux: - *_SCL or *_SDA: - 0: Standard(100kbps)& Fast(400kbps) mode - 1: Highspeed (3.4Mbps) mode - IC_DM or IC_DP: - 0: normal slew rate - 1: fast slew rate - Otherwise: - 0: fast slew rate - 1: normal slew rate -- input-enable: No arguments. Enable input (does not affect - output.) -- input-disable: No arguments. Disable input (does not affect - output.) -- drive-strength: Integer. Drive strength in mA. Valid values are - 2, 4, 6, 8, 10, 12, 14, 16 mA. - -Optional Properties (for I2C pins): - -- function: String. Specifies the pin mux selection. Values - must be one of: "alt1", "alt2", "alt3", "alt4" -- bias-pull-up: Integer. Pull up strength in Ohm. There are 3 - pull-up resisitors (1.2k, 1.8k, 2.7k) available - in parallel for I2C pins, so the valid values - are: 568, 720, 831, 1080, 1200, 1800, 2700 Ohm. -- bias-disable: No arguments. Disable pin bias. -- slew-rate: Integer. Meaning depends on configured pin mux: - *_SCL or *_SDA: - 0: Standard(100kbps)& Fast(400kbps) mode - 1: Highspeed (3.4Mbps) mode - IC_DM or IC_DP: - 0: normal slew rate - 1: fast slew rate - Otherwise: - 0: fast slew rate - 1: normal slew rate -- input-enable: No arguments. Enable input (does not affect - output.) -- input-disable: No arguments. Disable input (does not affect - output.) - -Optional Properties (for HDMI pins): - -- function: String. Specifies the pin mux selection. Values - must be one of: "alt1", "alt2", "alt3", "alt4" -- slew-rate: Integer. Controls slew rate. - 0: Standard(100kbps)& Fast(400kbps) mode - 1: Highspeed (3.4Mbps) mode -- input-enable: No arguments. Enable input (does not affect - output.) -- input-disable: No arguments. Disable input (does not affect - output.) - -Example: -// pin controller node -pinctrl@35004800 { - compatible = "brcm,bcm11351-pinctrl"; - reg = <0x35004800 0x430>; - - // pin configuration node - dev_a_default: dev_a_active { - //group node defining 1 standard pin - grp_1 { - pins = "std_pin1"; - function = "alt1"; - input-schmitt-enable; - bias-disable; - slew-rate = <1>; - drive-strength = <4>; - }; - - // group node defining 2 I2C pins - grp_2 { - pins = "i2c_pin1", "i2c_pin2"; - function = "alt2"; - bias-pull-up = <720>; - input-enable; - }; - - // group node defining 2 HDMI pins - grp_3 { - pins = "hdmi_pin1", "hdmi_pin2"; - function = "alt3"; - slew-rate = <1>; - }; - - // other pin group nodes - ... - }; - - // other pin configuration nodes - ... -}; - -In the example above, "dev_a_active" is a pin configuration node with a number -of sub-nodes. In the pin group node "grp_1", one pin, "std_pin1", is defined in -the "pins" property. Thus, the remaining properties in the "grp_1" node applies -only to this pin, including the following settings: - - setting pinmux to "alt1" - - enabling schmitt-trigger (hystersis) mode - - disabling pin bias - - setting the slew-rate to 1 - - setting the drive strength to 4 mA -Note that neither "input-enable" nor "input-disable" was specified - the pinctrl -subsystem will therefore leave this property unchanged from whatever state it -was in before applying these changes. - -The "pins" property in the pin group node "grp_2" specifies two pins - -"i2c_pin1" and "i2c_pin2"; the remaining properties in this pin group node, -therefore, applies to both of these pins. The properties include: - - setting pinmux to "alt2" - - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors - in parallel) - - enabling both pins' input -"slew-rate" is not specified in this pin group node, so the slew-rate for these -pins are left as-is. - -Finally, "grp_3" defines two HDMI pins. The following properties are applied to -both pins: - - setting pinmux to "alt3" - - setting slew-rate to 1; for HDMI pins, this corresponds to the 3.4 Mbps - Highspeed mode -The input is neither enabled or disabled, and is left untouched. - -=== Pin Names and Type === - -The following are valid pin names and their pin types: - - "adcsync", Standard - "bat_rm", Standard - "bsc1_scl", I2C - "bsc1_sda", I2C - "bsc2_scl", I2C - "bsc2_sda", I2C - "classgpwr", Standard - "clk_cx8", Standard - "clkout_0", Standard - "clkout_1", Standard - "clkout_2", Standard - "clkout_3", Standard - "clkreq_in_0", Standard - "clkreq_in_1", Standard - "cws_sys_req1", Standard - "cws_sys_req2", Standard - "cws_sys_req3", Standard - "digmic1_clk", Standard - "digmic1_dq", Standard - "digmic2_clk", Standard - "digmic2_dq", Standard - "gpen13", Standard - "gpen14", Standard - "gpen15", Standard - "gpio00", Standard - "gpio01", Standard - "gpio02", Standard - "gpio03", Standard - "gpio04", Standard - "gpio05", Standard - "gpio06", Standard - "gpio07", Standard - "gpio08", Standard - "gpio09", Standard - "gpio10", Standard - "gpio11", Standard - "gpio12", Standard - "gpio13", Standard - "gpio14", Standard - "gps_pablank", Standard - "gps_tmark", Standard - "hdmi_scl", HDMI - "hdmi_sda", HDMI - "ic_dm", Standard - "ic_dp", Standard - "kp_col_ip_0", Standard - "kp_col_ip_1", Standard - "kp_col_ip_2", Standard - "kp_col_ip_3", Standard - "kp_row_op_0", Standard - "kp_row_op_1", Standard - "kp_row_op_2", Standard - "kp_row_op_3", Standard - "lcd_b_0", Standard - "lcd_b_1", Standard - "lcd_b_2", Standard - "lcd_b_3", Standard - "lcd_b_4", Standard - "lcd_b_5", Standard - "lcd_b_6", Standard - "lcd_b_7", Standard - "lcd_g_0", Standard - "lcd_g_1", Standard - "lcd_g_2", Standard - "lcd_g_3", Standard - "lcd_g_4", Standard - "lcd_g_5", Standard - "lcd_g_6", Standard - "lcd_g_7", Standard - "lcd_hsync", Standard - "lcd_oe", Standard - "lcd_pclk", Standard - "lcd_r_0", Standard - "lcd_r_1", Standard - "lcd_r_2", Standard - "lcd_r_3", Standard - "lcd_r_4", Standard - "lcd_r_5", Standard - "lcd_r_6", Standard - "lcd_r_7", Standard - "lcd_vsync", Standard - "mdmgpio0", Standard - "mdmgpio1", Standard - "mdmgpio2", Standard - "mdmgpio3", Standard - "mdmgpio4", Standard - "mdmgpio5", Standard - "mdmgpio6", Standard - "mdmgpio7", Standard - "mdmgpio8", Standard - "mphi_data_0", Standard - "mphi_data_1", Standard - "mphi_data_2", Standard - "mphi_data_3", Standard - "mphi_data_4", Standard - "mphi_data_5", Standard - "mphi_data_6", Standard - "mphi_data_7", Standard - "mphi_data_8", Standard - "mphi_data_9", Standard - "mphi_data_10", Standard - "mphi_data_11", Standard - "mphi_data_12", Standard - "mphi_data_13", Standard - "mphi_data_14", Standard - "mphi_data_15", Standard - "mphi_ha0", Standard - "mphi_hat0", Standard - "mphi_hat1", Standard - "mphi_hce0_n", Standard - "mphi_hce1_n", Standard - "mphi_hrd_n", Standard - "mphi_hwr_n", Standard - "mphi_run0", Standard - "mphi_run1", Standard - "mtx_scan_clk", Standard - "mtx_scan_data", Standard - "nand_ad_0", Standard - "nand_ad_1", Standard - "nand_ad_2", Standard - "nand_ad_3", Standard - "nand_ad_4", Standard - "nand_ad_5", Standard - "nand_ad_6", Standard - "nand_ad_7", Standard - "nand_ale", Standard - "nand_cen_0", Standard - "nand_cen_1", Standard - "nand_cle", Standard - "nand_oen", Standard - "nand_rdy_0", Standard - "nand_rdy_1", Standard - "nand_wen", Standard - "nand_wp", Standard - "pc1", Standard - "pc2", Standard - "pmu_int", Standard - "pmu_scl", I2C - "pmu_sda", I2C - "rfst2g_mtsloten3g", Standard - "rgmii_0_rx_ctl", Standard - "rgmii_0_rxc", Standard - "rgmii_0_rxd_0", Standard - "rgmii_0_rxd_1", Standard - "rgmii_0_rxd_2", Standard - "rgmii_0_rxd_3", Standard - "rgmii_0_tx_ctl", Standard - "rgmii_0_txc", Standard - "rgmii_0_txd_0", Standard - "rgmii_0_txd_1", Standard - "rgmii_0_txd_2", Standard - "rgmii_0_txd_3", Standard - "rgmii_1_rx_ctl", Standard - "rgmii_1_rxc", Standard - "rgmii_1_rxd_0", Standard - "rgmii_1_rxd_1", Standard - "rgmii_1_rxd_2", Standard - "rgmii_1_rxd_3", Standard - "rgmii_1_tx_ctl", Standard - "rgmii_1_txc", Standard - "rgmii_1_txd_0", Standard - "rgmii_1_txd_1", Standard - "rgmii_1_txd_2", Standard - "rgmii_1_txd_3", Standard - "rgmii_gpio_0", Standard - "rgmii_gpio_1", Standard - "rgmii_gpio_2", Standard - "rgmii_gpio_3", Standard - "rtxdata2g_txdata3g1", Standard - "rtxen2g_txdata3g2", Standard - "rxdata3g0", Standard - "rxdata3g1", Standard - "rxdata3g2", Standard - "sdio1_clk", Standard - "sdio1_cmd", Standard - "sdio1_data_0", Standard - "sdio1_data_1", Standard - "sdio1_data_2", Standard - "sdio1_data_3", Standard - "sdio4_clk", Standard - "sdio4_cmd", Standard - "sdio4_data_0", Standard - "sdio4_data_1", Standard - "sdio4_data_2", Standard - "sdio4_data_3", Standard - "sim_clk", Standard - "sim_data", Standard - "sim_det", Standard - "sim_resetn", Standard - "sim2_clk", Standard - "sim2_data", Standard - "sim2_det", Standard - "sim2_resetn", Standard - "sri_c", Standard - "sri_d", Standard - "sri_e", Standard - "ssp_extclk", Standard - "ssp0_clk", Standard - "ssp0_fs", Standard - "ssp0_rxd", Standard - "ssp0_txd", Standard - "ssp2_clk", Standard - "ssp2_fs_0", Standard - "ssp2_fs_1", Standard - "ssp2_fs_2", Standard - "ssp2_fs_3", Standard - "ssp2_rxd_0", Standard - "ssp2_rxd_1", Standard - "ssp2_txd_0", Standard - "ssp2_txd_1", Standard - "ssp3_clk", Standard - "ssp3_fs", Standard - "ssp3_rxd", Standard - "ssp3_txd", Standard - "ssp4_clk", Standard - "ssp4_fs", Standard - "ssp4_rxd", Standard - "ssp4_txd", Standard - "ssp5_clk", Standard - "ssp5_fs", Standard - "ssp5_rxd", Standard - "ssp5_txd", Standard - "ssp6_clk", Standard - "ssp6_fs", Standard - "ssp6_rxd", Standard - "ssp6_txd", Standard - "stat_1", Standard - "stat_2", Standard - "sysclken", Standard - "traceclk", Standard - "tracedt00", Standard - "tracedt01", Standard - "tracedt02", Standard - "tracedt03", Standard - "tracedt04", Standard - "tracedt05", Standard - "tracedt06", Standard - "tracedt07", Standard - "tracedt08", Standard - "tracedt09", Standard - "tracedt10", Standard - "tracedt11", Standard - "tracedt12", Standard - "tracedt13", Standard - "tracedt14", Standard - "tracedt15", Standard - "txdata3g0", Standard - "txpwrind", Standard - "uartb1_ucts", Standard - "uartb1_urts", Standard - "uartb1_urxd", Standard - "uartb1_utxd", Standard - "uartb2_urxd", Standard - "uartb2_utxd", Standard - "uartb3_ucts", Standard - "uartb3_urts", Standard - "uartb3_urxd", Standard - "uartb3_utxd", Standard - "uartb4_ucts", Standard - "uartb4_urts", Standard - "uartb4_urxd", Standard - "uartb4_utxd", Standard - "vc_cam1_scl", I2C - "vc_cam1_sda", I2C - "vc_cam2_scl", I2C - "vc_cam2_sda", I2C - "vc_cam3_scl", I2C - "vc_cam3_sda", I2C |