diff options
Diffstat (limited to 'dts/Bindings/pinctrl/mediatek,pinctrl-mt6795.yaml')
| -rw-r--r-- | dts/Bindings/pinctrl/mediatek,pinctrl-mt6795.yaml | 224 |
1 files changed, 224 insertions, 0 deletions
diff --git a/dts/Bindings/pinctrl/mediatek,pinctrl-mt6795.yaml b/dts/Bindings/pinctrl/mediatek,pinctrl-mt6795.yaml new file mode 100644 index 0000000000..73ae6e1141 --- /dev/null +++ b/dts/Bindings/pinctrl/mediatek,pinctrl-mt6795.yaml @@ -0,0 +1,224 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/mediatek,pinctrl-mt6795.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT6795 Pin Controller + +maintainers: + - AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> + - Sean Wang <sean.wang@kernel.org> + +description: | + The Mediatek's Pin controller is used to control SoC pins. + +properties: + compatible: + const: mediatek,mt6795-pinctrl + + gpio-controller: true + + '#gpio-cells': + description: | + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + const: 2 + + gpio-ranges: + description: GPIO valid number range. + maxItems: 1 + + reg: + description: + Physical address base for gpio base and eint registers. + minItems: 2 + + reg-names: + items: + - const: base + - const: eint + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + interrupts: + description: The interrupt outputs to sysirq. + maxItems: 1 + +# PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + additionalProperties: false + patternProperties: + '^pins': + type: object + additionalProperties: false + description: | + A pinctrl node should contain at least one subnodes representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive strength, input enable/disable and + input schmitt. + An example of using macro: + pincontroller { + /* GPIO0 set as multifunction GPIO0 */ + gpio-pins { + pins { + pinmux = <PINMUX_GPIO0__FUNC_GPIO0>; + } + }; + /* GPIO45 set as multifunction SDA0 */ + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO45__FUNC_SDA0>; + } + }; + }; + $ref: "pinmux-node.yaml" + + properties: + pinmux: + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h + directly. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + + bias-pull-down: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt6795 pull down PUPD/R0/R1 type define value. + description: | + For normal pull down type, it is not necessary to specify R1R0 + values; When pull down type is PUPD/R0/R1, adding R1R0 defines + will set different resistance values. + + bias-pull-up: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt6795 pull up PUPD/R0/R1 type define value. + description: | + For normal pull up type, it is not necessary to specify R1R0 + values; When pull up type is PUPD/R0/R1, adding R1R0 defines + will set different resistance values. + + bias-disable: true + + output-high: true + + output-low: true + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + mediatek,pull-up-adv: + description: | + Pull up setings for 2 pull resistors, R0 and R1. User can + configure those special pins. Valid arguments are described as below: + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + + mediatek,pull-down-adv: + description: | + Pull down settings for 2 pull resistors, R0 and R1. User can + configure those special pins. Valid arguments are described as below: + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + + required: + - pinmux + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/pinctrl/mt6795-pinfunc.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + pio: pinctrl@10005000 { + compatible = "mediatek,mt6795-pinctrl"; + reg = <0 0x10005000 0 0x1000>, <0 0x1000b000 0 0x1000>; + reg-names = "base", "eint"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pio 0 0 196>; + interrupt-controller; + interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <2>; + + i2c0-pins { + pins-sda-scl { + pinmux = <PINMUX_GPIO45__FUNC_SDA0>, + <PINMUX_GPIO46__FUNC_SCL0>; + }; + }; + + mmc0-pins { + pins-cmd-dat { + pinmux = <PINMUX_GPIO154__FUNC_MSDC0_DAT0>, + <PINMUX_GPIO155__FUNC_MSDC0_DAT1>, + <PINMUX_GPIO156__FUNC_MSDC0_DAT2>, + <PINMUX_GPIO157__FUNC_MSDC0_DAT3>, + <PINMUX_GPIO158__FUNC_MSDC0_DAT4>, + <PINMUX_GPIO159__FUNC_MSDC0_DAT5>, + <PINMUX_GPIO160__FUNC_MSDC0_DAT6>, + <PINMUX_GPIO161__FUNC_MSDC0_DAT7>, + <PINMUX_GPIO162__FUNC_MSDC0_CMD>; + input-enable; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; + }; + + pins-clk { + pinmux = <PINMUX_GPIO163__FUNC_MSDC0_CLK>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; + }; + + pins-rst { + pinmux = <PINMUX_GPIO165__FUNC_MSDC0_RSTB>; + bias-pull-up = <MTK_PUPD_SET_R1R0_10>; + }; + }; + }; + }; |