diff options
Diffstat (limited to 'dts/Bindings/pinctrl/pinctrl-bindings.txt')
| -rw-r--r-- | dts/Bindings/pinctrl/pinctrl-bindings.txt | 190 |
1 files changed, 190 insertions, 0 deletions
diff --git a/dts/Bindings/pinctrl/pinctrl-bindings.txt b/dts/Bindings/pinctrl/pinctrl-bindings.txt new file mode 100644 index 0000000000..4414163e76 --- /dev/null +++ b/dts/Bindings/pinctrl/pinctrl-bindings.txt @@ -0,0 +1,190 @@ +== Introduction == + +Hardware modules that control pin multiplexing or configuration parameters +such as pull-up/down, tri-state, drive-strength etc are designated as pin +controllers. Each pin controller must be represented as a node in device tree, +just like any other hardware module. + +Hardware modules whose signals are affected by pin configuration are +designated client devices. Again, each client device must be represented as a +node in device tree, just like any other hardware module. + +For a client device to operate correctly, certain pin controllers must +set up certain specific pin configurations. Some client devices need a +single static pin configuration, e.g. set up during initialization. Others +need to reconfigure pins at run-time, for example to tri-state pins when the +device is inactive. Hence, each client device can define a set of named +states. The number and names of those states is defined by the client device's +own binding. + +The common pinctrl bindings defined in this file provide an infrastructure +for client device device tree nodes to map those state names to the pin +configuration used by those states. + +Note that pin controllers themselves may also be client devices of themselves. +For example, a pin controller may set up its own "active" state when the +driver loads. This would allow representing a board's static pin configuration +in a single place, rather than splitting it across multiple client device +nodes. The decision to do this or not somewhat rests with the author of +individual board device tree files, and any requirements imposed by the +bindings for the individual client devices in use by that board, i.e. whether +they require certain specific named states for dynamic pin configuration. + +== Pinctrl client devices == + +For each client device individually, every pin state is assigned an integer +ID. These numbers start at 0, and are contiguous. For each state ID, a unique +property exists to define the pin configuration. Each state may also be +assigned a name. When names are used, another property exists to map from +those names to the integer IDs. + +Each client device's own binding determines the set of states the must be +defined in its device tree node, and whether to define the set of state +IDs that must be provided, or whether to define the set of state names that +must be provided. + +Required properties: +pinctrl-0: List of phandles, each pointing at a pin configuration + node. These referenced pin configuration nodes must be child + nodes of the pin controller that they configure. Multiple + entries may exist in this list so that multiple pin + controllers may be configured, or so that a state may be built + from multiple nodes for a single pin controller, each + contributing part of the overall configuration. See the next + section of this document for details of the format of these + pin configuration nodes. + + In some cases, it may be useful to define a state, but for it + to be empty. This may be required when a common IP block is + used in an SoC either without a pin controller, or where the + pin controller does not affect the HW module in question. If + the binding for that IP block requires certain pin states to + exist, they must still be defined, but may be left empty. + +Optional properties: +pinctrl-1: List of phandles, each pointing at a pin configuration + node within a pin controller. +... +pinctrl-n: List of phandles, each pointing at a pin configuration + node within a pin controller. +pinctrl-names: The list of names to assign states. List entry 0 defines the + name for integer state ID 0, list entry 1 for state ID 1, and + so on. + +For example: + + /* For a client device requiring named states */ + device { + pinctrl-names = "active", "idle"; + pinctrl-0 = <&state_0_node_a>; + pinctrl-1 = <&state_1_node_a &state_1_node_b>; + }; + + /* For the same device if using state IDs */ + device { + pinctrl-0 = <&state_0_node_a>; + pinctrl-1 = <&state_1_node_a &state_1_node_b>; + }; + + /* + * For an IP block whose binding supports pin configuration, + * but in use on an SoC that doesn't have any pin control hardware + */ + device { + pinctrl-names = "active", "idle"; + pinctrl-0 = <>; + pinctrl-1 = <>; + }; + +== Pin controller devices == + +Pin controller devices should contain the pin configuration nodes that client +devices reference. + +For example: + + pincontroller { + ... /* Standard DT properties for the device itself elided */ + + state_0_node_a { + ... + }; + state_1_node_a { + ... + }; + state_1_node_b { + ... + }; + } + +The contents of each of those pin configuration child nodes is defined +entirely by the binding for the individual pin controller device. There +exists no common standard for this content. + +The pin configuration nodes need not be direct children of the pin controller +device; they may be grandchildren, for example. Whether this is legal, and +whether there is any interaction between the child and intermediate parent +nodes, is again defined entirely by the binding for the individual pin +controller device. + +== Generic pin configuration node content == + +Many data items that are represented in a pin configuration node are common +and generic. Pin control bindings should use the properties defined below +where they are applicable; not all of these properties are relevant or useful +for all hardware or binding structures. Each individual binding document +should state which of these generic properties, if any, are used, and the +structure of the DT nodes that contain these properties. + +Supported generic properties are: + +pins - the list of pins that properties in the node + apply to +function - the mux function to select +bias-disable - disable any pin bias +bias-high-impedance - high impedance mode ("third-state", "floating") +bias-bus-hold - latch weakly +bias-pull-up - pull up the pin +bias-pull-down - pull down the pin +bias-pull-pin-default - use pin-default pull state +drive-push-pull - drive actively high and low +drive-open-drain - drive with open drain +drive-open-source - drive with open source +drive-strength - sink or source at most X mA +input-enable - enable input on pin (no effect on output) +input-disable - disable input on pin (no effect on output) +input-schmitt-enable - enable schmitt-trigger mode +input-schmitt-disable - disable schmitt-trigger mode +input-debounce - debounce mode with debound time X +low-power-enable - enable low power mode +low-power-disable - disable low power mode +output-low - set the pin to output mode with low level +output-high - set the pin to output mode with high level +slew-rate - set the slew rate + +Some of the generic properties take arguments. For those that do, the +arguments are described below. + +- pins takes a list of pin names or IDs as a required argument. The specific + binding for the hardware defines: + - Whether the entries are integers or strings, and their meaning. + +- function takes a list of function names/IDs as a required argument. The + specific binding for the hardware defines: + - Whether the entries are integers or strings, and their meaning. + - Whether only a single entry is allowed (which is applied to all entries + in the pins property), or whether there may alternatively be one entry per + entry in the pins property, in which case the list lengths must match, and + for each list index i, the function at list index i is applied to the pin + at list index i. + +- bias-pull-up, -down and -pin-default take as optional argument on hardware + supporting it the pull strength in Ohm. bias-disable will disable the pull. + +- drive-strength takes as argument the target strength in mA. + +- input-debounce takes the debounce time in usec as argument + or 0 to disable debouncing + +More in-depth documentation on these parameters can be found in +<include/linux/pinctrl/pinconfig-generic.h> |