diff options
Diffstat (limited to 'dts/Bindings/pinctrl')
| -rw-r--r-- | dts/Bindings/pinctrl/atmel,at91-pinctrl.txt | 22 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt | 14 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/pinctrl-bindings.txt | 50 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/qcom,apq8064-pinctrl.txt | 2 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/qcom,apq8084-pinctrl.txt | 179 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/rockchip,pinctrl.txt | 6 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/ti,omap-pinctrl.txt | 13 |
7 files changed, 261 insertions, 25 deletions
diff --git a/dts/Bindings/pinctrl/atmel,at91-pinctrl.txt b/dts/Bindings/pinctrl/atmel,at91-pinctrl.txt index 02ab5ab198..b7a93e80a3 100644 --- a/dts/Bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/dts/Bindings/pinctrl/atmel,at91-pinctrl.txt @@ -19,6 +19,7 @@ such as pull-up, multi drive, etc. Required properties for iomux controller: - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl" + or "atmel,sama5d3-pinctrl" - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be configured in this periph mode. All the periph and bank need to be describe. @@ -85,13 +86,20 @@ Required properties for pin configuration node: PIN_BANK 0 is pioA, PIN_BANK 1 is pioB... Bits used for CONFIG: -PULL_UP (1 << 0): indicate this pin need a pull up. -MULTIDRIVE (1 << 1): indicate this pin need to be configured as multidrive. -DEGLITCH (1 << 2): indicate this pin need deglitch. -PULL_DOWN (1 << 3): indicate this pin need a pull down. -DIS_SCHMIT (1 << 4): indicate this pin need to disable schmit trigger. -DEBOUNCE (1 << 16): indicate this pin need debounce. -DEBOUNCE_VAL (0x3fff << 17): debounce val. +PULL_UP (1 << 0): indicate this pin needs a pull up. +MULTIDRIVE (1 << 1): indicate this pin needs to be configured as multi-drive. + Multi-drive is equivalent to open-drain type output. +DEGLITCH (1 << 2): indicate this pin needs deglitch. +PULL_DOWN (1 << 3): indicate this pin needs a pull down. +DIS_SCHMIT (1 << 4): indicate this pin needs to the disable schmitt trigger. +DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the + following values: + 00 - No change (reset state value kept) + 01 - Low + 10 - Medium + 11 - High +DEBOUNCE (1 << 16): indicate this pin needs debounce. +DEBOUNCE_VAL (0x3fff << 17): debounce value. NOTE: Some requirements for using atmel,at91rm9200-pinctrl binding: diff --git a/dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt b/dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt index 6464bf7694..189814e7cd 100644 --- a/dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt +++ b/dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt @@ -10,6 +10,7 @@ Required properties: - reg: Should contain a list of base address and size pairs for: -- first entry - the drive strength and pad control registers. -- second entry - the pinmux registers + -- third entry - the MIPI_PAD_CTRL register Tegra124 adds the following optional properties for pin configuration subnodes. The macros for options are defined in the @@ -91,6 +92,12 @@ Valid values for pin and group names are: dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg, gmh, owr, uda, gpv, dev3, cec, usb_vbus_en, ao3, ao0, hv0, sdio4, ao4. + MIPI pad control groups: + + These support only the nvidia,function property. + + dsi_b + Valid values for nvidia,functions are: blink, cec, cldvfs, clk12, cpu, dap, dap1, dap2, dev3, displaya, @@ -101,14 +108,15 @@ Valid values for nvidia,functions are: sdmmc4, soc, spdif, spi1, spi2, spi3, spi4, spi5, spi6, trace, uarta, uartb, uartc, uartd, ulpi, usb, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6, vi, vi_alt1, vi_alt3, vimclk2, vimclk2_alt, sata, ccla, pe0, pe, pe1, - dp, rtck, sys, clk tmds. + dp, rtck, sys, clk tmds, csi, dsi_b Example: pinmux: pinmux { compatible = "nvidia,tegra124-pinmux"; - reg = <0x70000868 0x164 /* Pad control registers */ - 0x70003000 0x434>; /* PinMux registers */ + reg = <0x0 0x70000868 0x0 0x164>, /* Pad control registers */ + <0x0 0x70003000 0x0 0x434>, /* Mux registers */ + <0x0 0x70000820 0x0 0x8>; /* MIPI pad control */ }; Example pinmux entries: diff --git a/dts/Bindings/pinctrl/pinctrl-bindings.txt b/dts/Bindings/pinctrl/pinctrl-bindings.txt index fa40a17716..98eb94d91a 100644 --- a/dts/Bindings/pinctrl/pinctrl-bindings.txt +++ b/dts/Bindings/pinctrl/pinctrl-bindings.txt @@ -127,6 +127,24 @@ whether there is any interaction between the child and intermediate parent nodes, is again defined entirely by the binding for the individual pin controller device. +== Generic pin multiplexing node content == + +pin multiplexing nodes: + +function - the mux function to select +groups - the list of groups to select with this function + +Example: + +state_0_node_a { + function = "uart0"; + groups = "u0rxtx", "u0rtscts"; +}; +state_1_node_a { + function = "spi0"; + groups = "spi0pins"; +}; + == Generic pin configuration node content == Many data items that are represented in a pin configuration node are common @@ -139,8 +157,12 @@ structure of the DT nodes that contain these properties. Supported generic properties are: pins - the list of pins that properties in the node - apply to -function - the mux function to select + apply to (either this or "group" has to be + specified) +group - the group to apply the properties to, if the driver + supports configuration of whole groups rather than + individual pins (either this or "pins" has to be + specified) bias-disable - disable any pin bias bias-high-impedance - high impedance mode ("third-state", "floating") bias-bus-hold - latch weakly @@ -163,6 +185,21 @@ output-low - set the pin to output mode with low level output-high - set the pin to output mode with high level slew-rate - set the slew rate +For example: + +state_0_node_a { + pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */ + bias-pull-up; +}; +state_1_node_a { + pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */ + output-high; +}; +state_2_node_a { + group = "foo-group"; + bias-pull-up; +}; + Some of the generic properties take arguments. For those that do, the arguments are described below. @@ -170,15 +207,6 @@ arguments are described below. binding for the hardware defines: - Whether the entries are integers or strings, and their meaning. -- function takes a list of function names/IDs as a required argument. The - specific binding for the hardware defines: - - Whether the entries are integers or strings, and their meaning. - - Whether only a single entry is allowed (which is applied to all entries - in the pins property), or whether there may alternatively be one entry per - entry in the pins property, in which case the list lengths must match, and - for each list index i, the function at list index i is applied to the pin - at list index i. - - bias-pull-up, -down and -pin-default take as optional argument on hardware supporting it the pull strength in Ohm. bias-disable will disable the pull. diff --git a/dts/Bindings/pinctrl/qcom,apq8064-pinctrl.txt b/dts/Bindings/pinctrl/qcom,apq8064-pinctrl.txt index 92fae82f35..2fb90b37aa 100644 --- a/dts/Bindings/pinctrl/qcom,apq8064-pinctrl.txt +++ b/dts/Bindings/pinctrl/qcom,apq8064-pinctrl.txt @@ -50,7 +50,7 @@ Valid values for function are: gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1, gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm, - riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, + riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, ps_hold Example: diff --git a/dts/Bindings/pinctrl/qcom,apq8084-pinctrl.txt b/dts/Bindings/pinctrl/qcom,apq8084-pinctrl.txt new file mode 100644 index 0000000000..ffafa1990a --- /dev/null +++ b/dts/Bindings/pinctrl/qcom,apq8084-pinctrl.txt @@ -0,0 +1,179 @@ +Qualcomm APQ8084 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8960 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,apq8084-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio146, + sdc1_clk, + sdc1_cmd, + sdc1_data + sdc2_clk, + sdc2_cmd, + sdc2_data + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + adsp_ext, audio_ref, blsp_i2c1, blsp_i2c2, blsp_i2c3, + blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8, + blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12, + blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, + blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10, + blsp_spi11, blsp_spi12, blsp_uart1, blsp_uart2, blsp_uart3, + blsp_uart4, blsp_uart5, blsp_uart6, blsp_uart7, blsp_uart8, + blsp_uart9, blsp_uart10, blsp_uart11, blsp_uart12, + blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim4, blsp_uim5, + blsp_uim6, blsp_uim7, blsp_uim8, blsp_uim9, blsp_uim10, + blsp_uim11, blsp_uim12, cam_mclk0, cam_mclk1, cam_mclk2, + cam_mclk3, cci_async, cci_async_in0, cci_i2c0, cci_i2c1, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, + edp_hpd, gcc_gp1, gcc_gp2, gcc_gp3, gcc_obt, gcc_vtt,i + gp_mn, gp_pdm0, gp_pdm1, gp_pdm2, gp0_clk, gp1_clk, gpio, + hdmi_cec, hdmi_ddc, hdmi_dtest, hdmi_hpd, hdmi_rcv, hsic, + ldo_en, ldo_update, mdp_vsync, pci_e0, pci_e0_n, pci_e0_rst, + pci_e1, pci_e1_rst, pci_e1_rst_n, pci_e1_clkreq_n, pri_mi2s, + qua_mi2s, sata_act, sata_devsleep, sata_devsleep_n, + sd_write, sdc_emmc_mode, sdc3, sdc4, sec_mi2s, slimbus, + spdif_tx, spkr_i2s, spkr_i2s_ws, spss_geni, ter_mi2s, tsif1, + tsif2, uim, uim_batt_alarm + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@fd510000 { + compatible = "qcom,apq8084-pinctrl"; + reg = <0xfd510000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 208 0>; + + uart2: uart2-default { + mux { + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; + }; + + tx { + pins = "gpio4"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/dts/Bindings/pinctrl/rockchip,pinctrl.txt b/dts/Bindings/pinctrl/rockchip,pinctrl.txt index 4658b69d4f..388b213249 100644 --- a/dts/Bindings/pinctrl/rockchip,pinctrl.txt +++ b/dts/Bindings/pinctrl/rockchip,pinctrl.txt @@ -2,8 +2,8 @@ The Rockchip Pinmux Controller, enables the IC to share one PAD to several functional blocks. The sharing is done by -multiplexing the PAD input/output signals. For each PAD there are up to -4 muxing options with option 0 being the use as a GPIO. +multiplexing the PAD input/output signals. For each PAD there are several +muxing options with option 0 being the use as a GPIO. Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the @@ -58,7 +58,7 @@ Deprecated properties for gpio sub nodes: Required properties for pin configuration node: - rockchip,pins: 3 integers array, represents a group of pins mux and config setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>. - The MUX 0 means gpio and MUX 1 to 3 mean the specific device function. + The MUX 0 means gpio and MUX 1 to N mean the specific device function. The phandle of a node containing the generic pinconfig options to use, as described in pinctrl-bindings.txt in this directory. diff --git a/dts/Bindings/pinctrl/ti,omap-pinctrl.txt b/dts/Bindings/pinctrl/ti,omap-pinctrl.txt new file mode 100644 index 0000000000..88c80273da --- /dev/null +++ b/dts/Bindings/pinctrl/ti,omap-pinctrl.txt @@ -0,0 +1,13 @@ +OMAP Pinctrl definitions + +Required properties: +- compatible : Should be one of: + "ti,omap2420-padconf" - OMAP2420 compatible pinctrl + "ti,omap2430-padconf" - OMAP2430 compatible pinctrl + "ti,omap3-padconf" - OMAP3 compatible pinctrl + "ti,omap4-padconf" - OMAP4 compatible pinctrl + "ti,omap5-padconf" - OMAP5 compatible pinctrl + "ti,dra7-padconf" - DRA7 compatible pinctrl + "ti,am437-padconf" - AM437x compatible pinctrl + +See Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt for further details. |