diff options
Diffstat (limited to 'dts/Bindings/pinctrl')
| -rw-r--r-- | dts/Bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt | 3 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt | 4 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/qcom,msm8916-pinctrl.txt | 186 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/renesas,pfc-pinctrl.txt | 9 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/samsung-pinctrl.txt | 12 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/ste,nomadik.txt | 35 | ||||
| -rw-r--r-- | dts/Bindings/pinctrl/xlnx,zynq-pinctrl.txt | 104 |
8 files changed, 332 insertions, 22 deletions
diff --git a/dts/Bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/dts/Bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 93ce12eb42..fdd8046e65 100644 --- a/dts/Bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/dts/Bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -11,6 +11,7 @@ Required properties: "allwinner,sun5i-a10s-pinctrl" "allwinner,sun5i-a13-pinctrl" "allwinner,sun6i-a31-pinctrl" + "allwinner,sun6i-a31s-pinctrl" "allwinner,sun6i-a31-r-pinctrl" "allwinner,sun7i-a20-pinctrl" "allwinner,sun8i-a23-pinctrl" diff --git a/dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt b/dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt index 189814e7cd..ecb5c0d252 100644 --- a/dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt +++ b/dts/Bindings/pinctrl/nvidia,tegra124-pinmux.txt @@ -6,7 +6,8 @@ nvidia,tegra30-pinmux.txt. In fact, this document assumes that binding as a baseline, and only documents the differences between the two bindings. Required properties: -- compatible: "nvidia,tegra124-pinmux" +- compatible: For Tegra124, must contain "nvidia,tegra124-pinmux". For + Tegra132, must contain '"nvidia,tegra132-pinmux", "nvidia-tegra124-pinmux"'. - reg: Should contain a list of base address and size pairs for: -- first entry - the drive strength and pad control registers. -- second entry - the pinmux registers diff --git a/dts/Bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt b/dts/Bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt index 2f9c0bd664..30676ded85 100644 --- a/dts/Bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt +++ b/dts/Bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt @@ -13,7 +13,9 @@ how to describe and reference PHYs in device trees. Required properties: -------------------- -- compatible: should be "nvidia,tegra124-xusb-padctl" +- compatible: For Tegra124, must contain "nvidia,tegra124-xusb-padctl". + Otherwise, must contain '"nvidia,<chip>-xusb-padctl", + "nvidia-tegra124-xusb-padctl"', where <chip> is tegra132 or tegra210. - reg: Physical base address and length of the controller's registers. - resets: Must contain an entry for each entry in reset-names. See ../reset/reset.txt for details. diff --git a/dts/Bindings/pinctrl/qcom,msm8916-pinctrl.txt b/dts/Bindings/pinctrl/qcom,msm8916-pinctrl.txt new file mode 100644 index 0000000000..498caff602 --- /dev/null +++ b/dts/Bindings/pinctrl/qcom,msm8916-pinctrl.txt @@ -0,0 +1,186 @@ +Qualcomm MSM8916 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8916 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,msm8916-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. Valid pins are: + gpio0-gpio121, + sdc1_clk, + sdc1_cmd, + sdc1_data + sdc2_clk, + sdc2_cmd, + sdc2_data, + qdsd_cmd, + qdsd_data0, + qdsd_data1, + qdsd_data2, + qdsd_data3 + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, atest_char0, + atest_char1, atest_char2, atest_char3, atest_combodac, atest_gpsadc0, + atest_gpsadc1, atest_tsens, atest_wlan0, atest_wlan1, backlight_en, + bimc_dte0,bimc_dte1, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, + blsp_i2c5, blsp_i2c6, blsp_spi1, blsp_spi1_cs1, blsp_spi1_cs2, + blsp_spi1_cs3, blsp_spi2, blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, + blsp_spi3, blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, + blsp_spi5, blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, + cam1_rst, cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, + cci_timer0, cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, + display_5v, dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, + ext_lpass, flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, gsm0_tx1, + gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, ldo_en, + ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, nav_pps, nav_tsync, + pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, pri_mi2s_ws, prng_rosc, + pwr_crypto_enabled_a, pwr_crypto_enabled_b, pwr_modem_enabled_a, + pwr_modem_enabled_b, pwr_nav_enabled_a, pwr_nav_enabled_b, + qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, qdss_ctitrig_in_b0, + qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, qdss_ctitrig_out_a1, + qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, qdss_traceclk_a, + qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a, + qdss_tracedata_b, reset_n, sd_card, sd_write, sec_mi2s, smb_int, + ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3, uim_batt, wcss_bt, wcss_fm, + wcss_wlan, webcam1_rst + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@1000000 { + compatible = "qcom,msm8916-pinctrl"; + reg = <0x1000000 0x300000>; + interrupts = <0 208 0>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + uart2: uart2-default { + mux { + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; + }; + + tx { + pins = "gpio4"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; diff --git a/dts/Bindings/pinctrl/renesas,pfc-pinctrl.txt b/dts/Bindings/pinctrl/renesas,pfc-pinctrl.txt index daef6fad6a..bfe72ec055 100644 --- a/dts/Bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/dts/Bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -1,7 +1,7 @@ * Renesas Pin Function Controller (GPIO and Pin Mux/Config) -The Pin Function Controller (PFC) is a Pin Mux/Config controller. On SH7372, -SH73A0, R8A73A4 and R8A7740 it also acts as a GPIO controller. +The Pin Function Controller (PFC) is a Pin Mux/Config controller. On SH73A0, +R8A73A4 and R8A7740 it also acts as a GPIO controller. Pin Control @@ -10,13 +10,13 @@ Pin Control Required Properties: - compatible: should be one of the following. + - "renesas,pfc-emev2": for EMEV2 (EMMA Mobile EV2) compatible pin-controller. - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller. - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller. - "renesas,pfc-r8a7778": for R8A7778 (R-Mobile M1) compatible pin-controller. - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2) compatible pin-controller. - - "renesas,pfc-sh7372": for SH7372 (SH-Mobile AP4) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. - reg: Base address and length of each memory resource used by the pin @@ -75,8 +75,7 @@ bias-disable, bias-pull-up and bias-pull-down. GPIO ---- -On SH7372, SH73A0, R8A73A4 and R8A7740 the PFC node is also a GPIO controller -node. +On SH73A0, R8A73A4 and R8A7740 the PFC node is also a GPIO controller node. Required Properties: diff --git a/dts/Bindings/pinctrl/samsung-pinctrl.txt b/dts/Bindings/pinctrl/samsung-pinctrl.txt index 8425838a6d..9d2a995293 100644 --- a/dts/Bindings/pinctrl/samsung-pinctrl.txt +++ b/dts/Bindings/pinctrl/samsung-pinctrl.txt @@ -171,6 +171,18 @@ Aliases: All the pin controller nodes should be represented in the aliases node using the following format 'pinctrl{n}' where n is a unique number for the alias. +Aliases for controllers compatible with "samsung,exynos7-pinctrl": +- pinctrl0: pin controller of ALIVE block, +- pinctrl1: pin controller of BUS0 block, +- pinctrl2: pin controller of NFC block, +- pinctrl3: pin controller of TOUCH block, +- pinctrl4: pin controller of FF block, +- pinctrl5: pin controller of ESE block, +- pinctrl6: pin controller of FSYS0 block, +- pinctrl7: pin controller of FSYS1 block, +- pinctrl8: pin controller of BUS1 block, +- pinctrl9: pin controller of AUDIO block, + Example: A pin-controller node with pin banks: pinctrl_0: pinctrl@11400000 { diff --git a/dts/Bindings/pinctrl/ste,nomadik.txt b/dts/Bindings/pinctrl/ste,nomadik.txt index 6b33b9f18e..f63fcb3ed3 100644 --- a/dts/Bindings/pinctrl/ste,nomadik.txt +++ b/dts/Bindings/pinctrl/ste,nomadik.txt @@ -16,17 +16,22 @@ mux function to select on those pin(s)/group(s), and various pin configuration parameters, such as input, output, pull up, pull down... The name of each subnode is not important; all subnodes should be enumerated -and processed purely based on their content. +and processed purely based on their content. The subnodes use the generic +pin multiplexing node layout from the standard pin control bindings +(see pinctrl-bindings.txt): -Required subnode-properties: -- ste,pins : An array of strings. Each string contains the name of a pin or - group. - -Optional subnode-properties: -- ste,function: A string containing the name of the function to mux to the +Required pin multiplexing subnode properties: +- function: A string containing the name of the function to mux to the pin or group. +- groups : An array of strings. Each string contains the name of a pin + group that will be combined with the function to form a multiplexing + set-up. -- ste,config: Handle of pin configuration node (e.g. ste,config = <&slpm_in_wkup_pdis>) +Required pin configuration subnode properties: +- pins: A string array describing the pins affected by the configuration + in the node. +- ste,config: Handle of pin configuration node + (e.g. ste,config = <&slpm_in_wkup_pdis>) - ste,input : <0/1/2> 0: input with no pull @@ -97,32 +102,32 @@ Example board file extract: uart0 { uart0_default_mux: uart0_mux { u0_default_mux { - ste,function = "u0"; - ste,pins = "u0_a_1"; + function = "u0"; + pins = "u0_a_1"; }; }; uart0_default_mode: uart0_default { uart0_default_cfg1 { - ste,pins = "GPIO0", "GPIO2"; + pins = "GPIO0", "GPIO2"; ste,input = <1>; }; uart0_default_cfg2 { - ste,pins = "GPIO1", "GPIO3"; + pins = "GPIO1", "GPIO3"; ste,output = <1>; }; }; uart0_sleep_mode: uart0_sleep { uart0_sleep_cfg1 { - ste,pins = "GPIO0", "GPIO2"; + pins = "GPIO0", "GPIO2"; ste,config = <&slpm_in_wkup_pdis>; }; uart0_sleep_cfg2 { - ste,pins = "GPIO1"; + pins = "GPIO1"; ste,config = <&slpm_out_hi_wkup_pdis>; }; uart0_sleep_cfg3 { - ste,pins = "GPIO3"; + pins = "GPIO3"; ste,config = <&slpm_out_wkup_pdis>; }; }; diff --git a/dts/Bindings/pinctrl/xlnx,zynq-pinctrl.txt b/dts/Bindings/pinctrl/xlnx,zynq-pinctrl.txt new file mode 100644 index 0000000000..b7b55a964f --- /dev/null +++ b/dts/Bindings/pinctrl/xlnx,zynq-pinctrl.txt @@ -0,0 +1,104 @@ + Binding for Xilinx Zynq Pinctrl + +Required properties: +- compatible: "xlnx,zynq-pinctrl" +- syscon: phandle to SLCR +- reg: Offset and length of pinctrl space in SLCR + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Zynq's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, slew rate, etc. + +Each configuration node can consist of multiple nodes describing the pinmux and +pinconf options. Those nodes can be pinmux nodes or pinconf nodes. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Required properties for pinmux nodes are: + - groups: A list of pinmux groups. + - function: The name of a pinmux function to activate for the specified set + of groups. + +Required properties for configuration nodes: +One of: + - pins: a list of pin names + - groups: A list of pinmux groups. + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pinmux subnode: + groups, function + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pinconf subnode: + groups, pins, bias-disable, bias-high-impedance, bias-pull-up, slew-rate, + low-power-disable, low-power-enable + + Valid arguments for 'slew-rate' are '0' and '1' to select between slow and fast + respectively. + + Valid values for groups are: + ethernet0_0_grp, ethernet1_0_grp, mdio0_0_grp, mdio1_0_grp, + qspi0_0_grp, qspi1_0_grp, qspi_fbclk, qspi_cs1_grp, spi0_0_grp, + spi0_1_grp - spi0_2_grp, spi1_0_grp - spi1_3_grp, sdio0_0_grp - sdio0_2_grp, + sdio1_0_grp - sdio1_3_grp, sdio0_emio_wp, sdio0_emio_cd, sdio1_emio_wp, + sdio1_emio_cd, smc0_nor, smc0_nor_cs1_grp, smc0_nor_addr25_grp, smc0_nand, + can0_0_grp - can0_10_grp, can1_0_grp - can1_11_grp, uart0_0_grp - uart0_10_grp, + uart1_0_grp - uart1_11_grp, i2c0_0_grp - i2c0_10_grp, i2c1_0_grp - i2c1_10_grp, + ttc0_0_grp - ttc0_2_grp, ttc1_0_grp - ttc1_2_grp, swdt0_0_grp - swdt0_4_grp, + gpio0_0_grp - gpio0_53_grp, usb0_0_grp, usb1_0_grp + + Valid values for pins are: + MIO0 - MIO53 + + Valid values for function are: + ethernet0, ethernet1, mdio0, mdio1, qspi0, qspi1, qspi_fbclk, qspi_cs1, + spi0, spi1, sdio0, sdio0_pc, sdio0_cd, sdio0_wp, + sdio1, sdio1_pc, sdio1_cd, sdio1_wp, + smc0_nor, smc0_nor_cs1, smc0_nor_addr25, smc0_nand, can0, can1, uart0, uart1, + i2c0, i2c1, ttc0, ttc1, swdt0, gpio0, usb0, usb1 + +The following driver-specific properties as defined here are valid to specify in +a pin configuration subnode: + - io-standard: Configure the pin to use the selected IO standard according to + this mapping: + 1: LVCMOS18 + 2: LVCMOS25 + 3: LVCMOS33 + 4: HSTL + +Example: + pinctrl0: pinctrl@700 { + compatible = "xlnx,pinctrl-zynq"; + reg = <0x700 0x200>; + syscon = <&slcr>; + + pinctrl_uart1_default: uart1-default { + mux { + groups = "uart1_10_grp"; + function = "uart1"; + }; + + conf { + groups = "uart1_10_grp"; + slew-rate = <0>; + io-standard = <1>; + }; + + conf-rx { + pins = "MIO49"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO48"; + bias-disable; + }; + }; + }; |