diff options
Diffstat (limited to 'dts/Bindings/power/power_domain.txt')
| -rw-r--r-- | dts/Bindings/power/power_domain.txt | 65 |
1 files changed, 65 insertions, 0 deletions
diff --git a/dts/Bindings/power/power_domain.txt b/dts/Bindings/power/power_domain.txt index 14bd9e945f..f3355313c0 100644 --- a/dts/Bindings/power/power_domain.txt +++ b/dts/Bindings/power/power_domain.txt @@ -40,6 +40,12 @@ Optional properties: domain's idle states. In the absence of this property, the domain would be considered as capable of being powered-on or powered-off. +- operating-points-v2 : Phandles to the OPP tables of power domains provided by + a power domain provider. If the provider provides a single power domain only + or all the power domains provided by the provider have identical OPP tables, + then this shall contain a single phandle. Refer to ../opp/opp.txt for more + information. + Example: power: power-controller@12340000 { @@ -120,4 +126,63 @@ The node above defines a typical PM domain consumer device, which is located inside a PM domain with index 0 of a power controller represented by a node with the label "power". +Optional properties: +- required-opp: This contains phandle to an OPP node in another device's OPP + table. It may contain an array of phandles, where each phandle points to an + OPP of a different device. It should not contain multiple phandles to the OPP + nodes in the same OPP table. This specifies the minimum required OPP of the + device(s), whose OPP's phandle is present in this property, for the + functioning of the current device at the current OPP (where this property is + present). + +Example: +- OPP table for domain provider that provides two domains. + + domain0_opp_table: opp-table0 { + compatible = "operating-points-v2"; + + domain0_opp_0: opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <975000 970000 985000>; + }; + domain0_opp_1: opp-1100000000 { + opp-hz = /bits/ 64 <1100000000>; + opp-microvolt = <1000000 980000 1010000>; + }; + }; + + domain1_opp_table: opp-table1 { + compatible = "operating-points-v2"; + + domain1_opp_0: opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <975000 970000 985000>; + }; + domain1_opp_1: opp-1300000000 { + opp-hz = /bits/ 64 <1300000000>; + opp-microvolt = <1000000 980000 1010000>; + }; + }; + + power: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <1>; + operating-points-v2 = <&domain0_opp_table>, <&domain1_opp_table>; + }; + + leaky-device0@12350000 { + compatible = "foo,i-leak-current"; + reg = <0x12350000 0x1000>; + power-domains = <&power 0>; + required-opp = <&domain0_opp_0>; + }; + + leaky-device1@12350000 { + compatible = "foo,i-leak-current"; + reg = <0x12350000 0x1000>; + power-domains = <&power 1>; + required-opp = <&domain1_opp_1>; + }; + [1]. Documentation/devicetree/bindings/power/domain-idle-state.txt |